Raidon iR2623 User manual

V1.3 (Jan. 2019)
1. 2.5" 硬碟讀取燈
2. 2.5" 硬碟鑰匙孔
3. 2.5" 硬碟抽取盒
4. 液晶顯示面板
5. 故障顯示燈
6. 主硬碟狀態指示燈
7. 次硬碟狀態指示燈
8. 靜音按鍵
9. 3.5" 硬碟抽盒把手
10. 硬碟卡榫按鍵
11. 主硬碟讀取燈
12. 次硬碟讀取燈
13. 散熱風扇
14. RAID 模式設定
15. RS232 埠
16. 3.5" 硬碟 SATA 連接埠
17. SATA 15Pin 電源輸入埠
18. 4Pin 電源輸入埠
19. 2.5" 硬碟 SATA 連接埠
iR2623-S3 快速安裝導引
產品示意圖與配件表
iR2623-S3 配件內容
iR2623-S3 產品本體X1(內含抽取盒x3)
內接RS232線 x1
外接RS232線 x1
SATA線 x1
快速安裝導引 x 1
螺絲及鑰匙
打開包裝外盒後，包裝內容應包含下列組件 :
1. 電腦或伺服器具備SATA I、SATA II或SATA III介面。
2. 具備SATA I、SATA II或SATA III介面的硬碟。
3. 強烈建議使用iR2623-S3前先設定好RAID模式(預設值是RAID 1)。
4. 在新增或變更RAID模式後需重新啟動產品，以確保完成更新為新的RAID模式。
5. 本系統允許使用不同廠牌的硬碟。但如果要獲得更好的效能，我們強烈建議使用相同廠牌型號
的硬碟。
6. 安裝硬碟前請先確認所使用的硬碟並無壞軌或是其他問題，以免導致系統損毀或資料遺失。
7. 硬碟格式化後，iR2623-S3的總使用儲存容量或許會與硬碟容量加總後的有所不同。
8. 強烈建議除了使用iR2623-S3的資料儲存功能外，請針對重要資料備份到另一個儲存裝置上或
遠端備份，雙重備援您重要的資料。若您儲存在iR2623-S3的資料損毀或遺失，RAIDON將不負任
何的責任。
1. 開機與正常待機狀態.
iR2623
RAID-1 vxxxxxx.x
產品使用注意事項
硬碟安裝
設定RAID 層級
請參照以下步驟完成硬體安裝
步驟1 拆開外包裝並取出產品本體。
步驟 2 將系統擺放於穩固平台，並確認散熱風風扇口沒有被其他物體擋住，系統四周有適當的散熱
空 間。
(擺放環境請避免接近潮濕或其他易對產品造成損傷的環境。)
步驟 3 請使用零件包內附的頂針插入鑰匙孔後，抽取盒門閂將會輕彈開啟，即可將硬碟抽取盒取出。
步驟 4 將硬碟安裝到抽取盒上，並以零件包內附的螺絲加以固定，以避免不必要的移動對硬碟造成
傷 害。
步驟 5 硬碟安裝完成後請將抽取盒平移放入主機內並關上把手。
步驟 6 將附件中的連接線分別接到電腦與iR2623-S3的相關連接埠。(參照以下圖)
請透過機器後面的jumper來設定RAID層級。出廠預設值是RAID 1。機器背面有三根pin腳用來設
定RAID層級，若要設定RAID 0模式，請選用下面兩根；若要設定RAID 1模式，請選用上面兩根。
1. RAID 1 模式
1). 將新的硬碟放入iR2623-S3中。強烈建議您使用兩顆相同的硬碟，以便取得對等的容量。
如果兩顆硬碟的容量不同，iR2623-S3將會以小容量的硬碟為依據。
2). RAID 1模式下，兩顆硬碟是鏡射關係因此擁有相同的資料，因此有一顆硬碟損毀仍然可以正
常運作。當放入新硬碟取代損毀硬碟後，系統會自動將資料重建到新的硬碟。
2. RAID 0 模式
1). 將新的硬碟放入iR2623-S3中。強烈建議您使用兩顆相同的硬碟，以便取得對等的容量。
如果兩顆硬碟的容量不同，iR2623-S3將會以小容量的硬碟為依據。
2). RAID 0模式下，兩顆硬碟的容量會被加總成一個大儲存容量，並且提供更佳的存取效能。
當iR2623的硬體安裝完成，即可準備進行行開機動作。
硬體安裝完成後，將BIOS的硬碟偵測設定為自動，iR2623-S3將會被視為如同一顆硬碟一般。當電
腦開機後，系統會顯示下列偵測訊息：
1. 安裝在iR2623-S3中的硬碟能夠被Windows的裝置管理員偵測到。
2. 使用iR2623-S3前，使用者可以透過磁碟管理選擇硬碟的格式。
到此完成整個安裝程序。使用者可以如同存取一般硬碟般的使用iR2623-S3。
硬碟格式化及磁碟機建立
LCD螢幕顯示與LED燈號說明
SATA
SATA
45cm SATA連接線
COM1
COM2
電源連接線
電源
主機版 SATA連接埠
iR2623-S3
內接主機殼示意圖
內接RS232連接線
外接RS232連接線
1
1
2
2
3
3
4
4
Pri HDD : OK
Sec HDD : OK
前視圖 背視圖
FAIL LED
PRI HDD MUTE
SEC HDD
2
3
4
5
7
8
10
1
9
10
9
6
11
12
13
14
16
19
18
17
15
狀態
面板燈號 3.5" 硬碟讀取燈
2.5" 硬碟
讀取燈 蜂鳴器
故障顯示燈 主硬碟
狀態指示燈
次硬碟
狀態指示燈
主硬碟
讀取燈
次硬碟
讀取燈
開機 — — 橘燈恆亮 藍紫燈閃爍 藍燈恆亮 — —
待機 — — 橘燈恆亮 藍燈恆亮 藍燈恆亮 — —
硬碟故障
（RAID降級）紅燈恆亮 — — 紅燈恆亮 藍燈恆亮 鳴叫
資料存取 — — 橘燈恆亮 藍紫燈閃爍 藍燈閃爍 — —
資料重建
(Source) —— 橘燈恆亮 藍燈恆亮 藍燈恆亮 — —
資料重建
(Target) —— — — 紅燈閃爍 藍燈恆亮 — —
風扇故障 紅燈恆亮 橘燈恆亮 藍燈恆亮 藍燈恆亮 鳴叫
溫度過高 紅燈恆亮 橘燈恆亮 藍燈恆亮 藍燈恆亮 鳴叫
請先確認相關配件與產品本身是否有受損或是缺少配件，若有任何疑問，請與您的經銷商或
業務人員聯絡。
請前往官網 (www.raidon.com.tw) 下載說明書、驅動程式以及其餘相關資源。
˙
˙

1. 2.5" HDD status indicator LED
2. 2.5" HDD tray ejector opening
3. 2.5" HDD removable tray
4. LCD Display
5. LED of failure Alarm
6. Pri HDD status indicator
7. Sec HDD status indicator
8. Mute Button
9. 3.5" Removable drive tray
10. HDD tray key lock
11. Pri HDD tray access light
12. Sec HDD tray access light
13. Cooling fan
14. RAID mode switch
15. RS232 Port
16. 3.5" SATA Port
17. 15 PIN SATA Port
18. 4Pin Power socket
19. 2.5" SATA Port
iR2623-S3 Quick Installation Guide
Package Contents and Product Views
iR2623-S3
iR2623-S3 X1(with removable drive tray enclosed x 3)
Internal RS232 Cable x 1
External RS232 Cable ｘ1
SATA Cable ｘ1
Quick Setup Guide x 1
Screws and keys
Open the package and you should find the following:
1. Computers or servers with SATA I & SATA II & SATA III.
2. Hard drive with SATA I & SATA II & SATA III.
3. You are strongly advised to set the storage mode (the default is the Independent mode) before using the
iR2623-S3.
4. The product needs to be restarted after adding or changing the RAID mode, and the update is
guaranteed to be the new RAID mode.
5. The product allows the user to simultaneously utilize two hard drives manu factured by different
companies. However, if the user expects better efficiency, we strongly recommend the users to use hard
drives manufactured by the same manufacturer.
6. Please make sure that the two hard drives are free from bad blocks or defects prior to installation in
order to avoid system crashes or data loss.
7. The actual storage capacity of iR2623-S3 recognized by the system may differ from the total capacity
stated on the hard drives combined once the drives have been formatted.
8. It is highly recommended for users to back up important data contained within the iR2623-S3 on a
regular basis or whenever the user feels necessary to a remote or a separate storage device. Stardom will
not be responsible for any lost of data caused during the use of the unit or the recovery of the data lost.
1. Booting and Normal status.
iR2623
RAID-1 vxxxxxx.x
Hardware Requirements and Precautions
Hardware Installation Procedure
Setting the Hard Drive Array Mode
Please follow the instructions below to complete the hardware installation.
Step 1 Open the package and take out the product making sure that all the enclosed contents are not
damaged or missing. Should you find damages or missing contents, please contact your supplier
immediately.
Step 2 Place the system on a stable surface. Ensure that it is well ventilated without blockage to the vent
and kept away from areas near water and damage prone areas.
Step 3 Use the key included in the accessory kit and inserted into the key access opening to eject the
removable drive tray latch and extract the removable drive tray.
Step 4 Mount your hard drives onto the removable drive tray and secure it with the screws included in
the accessory kit to avoid any damage to the hard drive due to accidental movements.
Step 5 When the hard drive installation has been completed, insert the hard drive tray into the system
horizontally and secure the latch into place.
Step 6 Use the preferred cable included to connect your computer to the relative interface connection on
the iR2623-S3 unit.
Please select the RAID mode with the jumper located at the back panel. The original default is RAID 1,
still there are three pins at the back panel for RAID mode selection: RAID 0 mode by setting the jumper
on the bottom of the two pins. RAID 1 mode by setting the jumper on the top of the two pins.
1. RAID 1 Mode
1). Place two new hard drives into iR2623-S3 and strongly suggest you to use two identical hard drives
to get the equal capacity. If the capacity is different, iR2623-S3 is downward to the small hard drive
capacity.
2). Under RAID 1 mode, two hard drives has the identical information as one to mirror to the other one,
therefore each of the hard drive failed is still able to function normally. When you replace the failed
hard disk to the new one the system automatically rebuilding the data to the newly place hard disk.
2. RAID 0 Mode
1). Place two new hard drives into iR2623-S3 and strongly suggest you to use two identical hard drives
to get the equal capacity. If the capacity is different, iR2623-S3 is downward to the small hard drive
capacity.
2). Under RAID 0 mode, capacity is add up to a one big volume, also with the feature of faster read/write
performance efficient.
When the hardware setup for iR2623-S3 is complete, you are now ready to turn the machine on.
After the hardware installation is complete, the iR2623-S3 will be treated as one single hard drive. Set
the hard drive to AUTO in the computer’s BIOS. When the computer is turned on, the system will
retrieve the following information:
1. In iR2623-S3, the installed hard drive can be detected by the Device Manager of Computer
Management for Windows.
2. Customers can choose to format the hard drive by using the Disk Management tool of the operating
system before using the iR2623-S3.
At this point, the installation process is completely finished.
The user can freely retrieve and save data to iR2623-S3 just like retrieving and saving data to a regular hard
drive.
Computer Set Up
LCD Display and LED Indicators
SATA
SATA
45cm SATA Cable
COM1
COM2
Power Supply Connector
Power Supply
Motherboard SATA Ports
iR2623-S3
Internal Case
Internal RS232 Cable
External RS232 Cable
1
1
2
2
3
3
4
4
Pri HDD : OK
Sec HDD : OK
Front View Rear View
FAIL LED
PRI HDD MUTE
SEC HDD
2
3
4
5
7
8
10
1
9
10
9
6
11
12
13
14
16
19
18
17
15
Status
Panel light 3.5" HDD tray access light 2.5"
HDD tray
access light
Buzzer
Fail LED Pri HDD
status indicator
Sec HDD
status indicator
Pri HDD tray
access light
Sec HDD tray
access light
Power On — — Orange light
always on
Blue light
always on — —
Stabdby — — Orange light
always on
Blue light
always on
Blue light
always on — —
HDD
Failure
Red light
always on — — Red light always on
Blue light
always on On
Access — — Orange light
always on
Blue light — —
Rebuilding
(Source) — — Orange light always on
Blue light
always on
Blue light
always on — —
Rebuilding
(Target) — — — — Red light Blue light
always on — —
Fan Failure Red light
always on
Orange light
always on
Blue light
always on
Blue light
always on On
Over Heat
（≥50℃)
Red light
always on
Orange light
always on
Blue light
always on
Blue light
always on On
Please check the product and accessories for any defect or missing parts. If you have
any questions, please contact your product supplier.
Please visit the official website (www.raidon.com.tw) to download user manuals, drivers
and other related resources.
˙
˙
V1.3 (Jan. 2019)
V1.3