Raidon intank ir2622 User manual

InTANK
iR2622
User Manual
Your Data Security Guardian

iR2622 User Manual
!
!2
» InTANK iR2622 User Manual ……………………………………………….3
» InTANK iR2622 產品使說明 ….…………………………..………………14

iR2622 User Manual
!
Thank you for purchasing RAIDON products. This manual will introduce the InTANK iR2622 Series.
Before using your InTANK iR2622, please read this manual thoroughly. Although all information
contained in this user manual has been carefully verified before publishing, however, the actual
product specification will be based on the time of delivery from RAIDON. Any updates to the product
specifications or relevant information may be found on www.raidon.com.tw. Products are subject to
change without prior notifications.
If you have any questions regarding the products of RAIDON, or you would like to know the latest
product information, user manual update, or firmware update, please contact your local supplier or
visit www.raidon.com.tw for further information.
Copyright © RAIDON TECHNOLOGY, INC. All rights reserved.
!
1. Package Contents and Product Views
2. Operating Information
3. Hardware Requirements and Precautions
4. Hardware Installation Procedure
5. Setting RAID Mode
6. Computer Set Up
7. Hard Disk status on LCD screen
8. Data Rebuilding Operation
9. GUI Monitoring Software and Firmware Update GUI
10. Frequently Asked Questions
!
Open the package and you should find the following:
Please make sure that the contents listed above are not damaged or missing. If you should find
damages or missing contents, please contact your supplier immediately.
Introduction
Table of Contents
1. Package Contents and Product Views
iR2622
iR2622ｘ1( with removable drive tray enclosed x2)
Internal RS232 Cable x 1
External RS232 Cable ｘ1
SATA Cable ｘ1
CD-Rom ｘ1
Accessories Kit bag ｘ2
Quick Installation Guide x 1
!3

iR2622 User Manual
Product View
!
1. LCD Display
2. LED of failure Alarm
3. Pri. HDD status indicator
4. Sec. HDD status indicator
5. Mute Button
6. Removable drive tray
7. HDD tray key lock
8. HDD Access
9. Cooling fan
10. RAID mode switch
11. RS232 Port
12. SATA Port
13. 15 PIN Power Connector
14. 4Pin Power Connector
LED Indicators :
Status
Fail LED
HDD 1
HDD 2
TRAY 1
TRAY 2
Buzzer
Stand by
——
Orange / light on
Blue / light on
——
HDD Failure
Red / light on
——
Red / light on
On
Access
——
Orange / light on
Blue and Purple / blinking
——
Rebuilding(Source)
——
Orange / light on
Blue / light on
——
Rebuilding(Target)
——
——
Red / blinking
——
Fan Failure
Red / light on
——
——
On
Over Heat(≥50 "C)
Red / light on
——
——
On
!4

iR2622 User Manual
!
Operating Temperature : 0 ~ 40 "C (32 ~ 104 "F)
Storage Temperature : -10 ~ 70 "C (14 ~ 158 "F)
Line Voltage : 100 ~ 240V AC
!
1. Computers or servers with SATA I & SATA II & SATA III.
2. Hard drive with SATA I & SATA II & SATA III
3. You are strongly advised to set the storage mode (the default is the Independent mode) before
using the iR2622.
4. The product allows the user to simultaneously utilize two hard drives manufactured by different
companies. However, if the user expects better efficiency, we strongly recommend the users to
use hard drives manufactured by the same manufacturer.
5. Please make sure that the two hard drives are free from bad blocks or defects prior to
installation in order to avoid system crashes or data loss.
6. The actual storage capacity of iR2622 recognized by the system may differ from the total
capacity stated on the hard drives combined once the drives have been formatted.
7. It is highly recommended for users to back up important data contained within the iR2622 unit
on a regular basis or whenever the user feels necessary to a remote or a separate storage
device. Stardom will not be responsible for any lost of data caused during the use of the unit or
the recovery of the data lost.
!
!
Please follow the instructions below to complete the hardware installation.
Step 1 Open the package and take out the product making sure that all the enclosed contents are
not damaged or missing. Should you find damages or missing contents, please contact your
supplier immediately.
Step 2 Place the system on a stable surface. Ensure that it is well ventilated without blockage to the
vent and kept away from areas near water and damage prone areas.
Step 3 Use the key included in the accessory kit and inserted into the key access opening to eject
the removable drive tray latch and extract the removable drive tray.
Step 4 Mount your hard drives onto the removable drive tray and secure it with the screws included
in the accessory kit to avoid any damage to the hard drive due to accidental movements.
Step 5 When the hard drive installation has been completed, insert the hard drive tray into the
system horizontally and secure the latch into place.
Step 6 Use the preferred cable included to connect your computer to the relative interface
connection on the iR2622 unit.
2. Operating Information
3. Hardware Requirements and Precautions
Note：
Once the drive mode configuration has been completed, re-configuration using the same hard drives to set
the drive mode will result in complete data loss. If you must change the drive mode, make sure to backup all
data prior to the mode change.
4. Hardware Installation Procedure
!5

iR2622 User Manual
※Note :
1. RS232 Port and RS232 Cable: Provides hardware status monitoring to industrial control system or IPC via RS232.
2. We do not recommend users to disassemble the device without proper instructions and authorization. The manufacture warranty
will not cover the damages caused by unauthorized disassembling.
3. To prevent the device from malfunction, please make sure the device is connected with a direct and dedicated power connection of
a stable power input.
!
Please select the RAID mode with the jumper located at the back panel. The original default is RAID
1, still there are three pins at the back panel for RAID mode selection: RAID 0 mode by setting the
jumper on the bottom of the two pins. RAID 1 mode by setting the jumper on the top of the two pins.
1. RAID 1 Mode
1). Place two new hard drives into iR2622 and strongly suggest you to use two identical hard
drives to get the equal capacity. If the capacity is different, iR2622 is downward to the small hard
drive capacity.
2). Under RAID 1 mode, two hard drives has the identical information as one to mirror to the other
one, therefore each of the hard drive failed is still able to function normally. When you replace the
failed hard disk to the new one the system automatically rebuilding the data to the newly place
hard disk.
2. RAID 0 Mode
1). Place two new hard drives into iR2622 and strongly suggest you to use two identical hard
drives to get the equal capacity. If the capacity is different, iR2622 is downward to the small hard
drive capacity.
2). Under RAID 0 mode, capacity is add up to a one big volume, also with the feature of faster
read/write performance efficient.
5. Setting the Hard Drive Array Mode
!6
SATA
SATA
45cm SATA Cable
Power Supply Connector
Internal Case
Internal RS232 Cable
External RS232 Cable
1
2
3
4
iR2622
COM1
COM2
1
2
3
4

iR2622 User Manual
!
When the hardware setup for iR2622 is complete, you are now ready to turn the machine on.
After the hardware installation is complete, the iR2622 will be treated as one single hard drive. Set
the hard drive to AUTO in the computer’s BIOS. When the computer is turned on, the system will
retrieve the following information:
1. In iR2622, the installed hard drive can be detected by the Device Manager of Computer
Management for Windows.
2. Customers can choose to format the hard drive by using the Disk Management tool of the
operating system before using the iR2622.
At this point, the installation process is completely finished. The user can freely retrieve and save
data to iR2622 just like retrieving and saving data to a regular hard drive. If the user experiences
any abnormality during the operation, please refer to the trouble shooting Q&A section in Appendix.
6. Computer Set Up
!7

iR2622 User Manual
!
1. Booting and Normal status.
2. Over Temperature (≥50 "C)
!
3. Fan Failure.
!
4. RAID 1 Degraded. Primary hard drive is failure, but secondary hard drive is normal.
!
5. RAID 1 Failure. Primary and secondary hard drives are failure.
!
6. RAID 1 Failure. (Double Source)
!
7. RAID 0 Failure. Primary hard drive is missing, but secondary hard drive is normal.
!
8. Rebuilding
!
7. Hard Disk status on LCD screen
Pri HDD : OK
Sec HDD : OK T
Pri HDD : OK F
Sec HDD : OK
RAID-1 degraded
Pri : X Sec : O
RAID-1 failure
Pri : X Sec : X
RAID-1 failure
Double Source
RAID-0 failure
Pri : M Sec :O
Rebuilding
Sec→Pri 32%
!8
iR2622
RAID-1 vxxxxxx.x
Pri HDD : OK
Sec HDD : OK

iR2622 User Manual
#
The hard drive Hot Swap and Auto Rebuilding functions are available.
Off-line Back up When the data is stored within iR2622, the user can remove one of the hard drives
from iR2622 as back up drive for data such as system operation file, secured files, seldom modified
files or image and music files. The user can periodically insert the hard drive back into iR2622 to
execute automatic backup to protect the system from being hit by computer virus or to avoid risk of
having both hard drives failing at the same time.
When one of the two hard drives fails in the iR2622 system, the system will alarm the hard drive
failure message both on the LCD display screen and in the monitoring software. The user can
remove the failed hard drive from the system while the system is still in operation without shutting
down the machine. If the failed hard drive is replaced shortly, the system will automatically execute
the Auto Rebuilding function without affecting the system operation and without any operation
command from the user.
When the iR2622 detects a hard drive missing or a hard drive failure, the Buzzer will start and the
LCD display screen will display the following messages:
!
After removing the failed hard drive and replacing with a new hard drive, if the hard drive is properly
installed, the LCD display screen will display the following messages:
!!
After few seconds of installing the new hard drive, the LCD display screen will display the data
rebuilding progress:
#
!!
When the rebuilding is fully completed, the LCD display screen will again display the following
messages:
!
RAID-1 degraded
Pri : X Sec : O
Pri HDD : OK
Sec HDD : Insert
Pri HDD :Insert
Sec HDD : OK
Rebuilding
Sec→Pri 32%
Rebuilding
Pri→Sec 32%
Pri HDD : OK
Sec HDD : OK
!9
8. Data Rebuilding Operation

iR2622 User Manual
!
You can install GUI software to monitor the status of iR2622. This can be done by installing software
from CD.
※The HDD1 equals to Pri HDD and HDD2 equals to Sec HDD.
1. System Status
This GUI will auto detects the connected iR2622 and reveals relative information accordingly.
2. Firmware Upgrade
You may update the Firmware via this GUI, simply click on “Load” button to locate the firmware
file to proceed. After update is finished, you may restart the power properly to operate with newly
updated firmware.#
※Caution : Any random firmware updates may cause device in malfunction, it is strongly suggested not to update device firmware if
device is operating properly.
9. GUI Monitoring Software and Firmware Update
!10