Ranger design 1525-FTR User manual

INSTALLATION GUIDE
1525-FTR Combination Ladder Rack
Regular Ford Transit 130” Wheelbase ( Aluminum )

QUICK START GUIDE
REQUIRED ITEMS
2
PERSONS
q1.1 Setup...............................................................................................................................................
q1.2 Ladder Rack Assembly....................................................................................................................
3 - 5
5 - 16
q2.1 Mounting Tracks Installation............................................................................................................
q2.2 Ladder Rack Installation..................................................................................................................
q2.3 Note.................................................................................................................................................
17
18 - 22
23
Phase 1 - Assembly
Phase 2 - Installation
NOTE: Use Sawhorses if possible, or use the box as a at protective surface on the ground or table.
qCordless Impact
qRatchet
qTape Measure
qMallet
qMarker
qLadder
qCutter
q1/2" Socket
q13mm Socket
qSawhorse ( Optional )
qBox
qKnife
q1/2" Wrench
qSilicone

For technical support, contact us at 1-800-565-5321 1525-FTR Installation Guide |REV. B3 | Page 3
PHASE 1 – ASSEMBLY
1.1 SETUP
1.1.1 Unpack components; compare with the bill of materials.
1.1.2 Verify all parts are present.
Item No. Description Qty.
10-149 Clamp Handle Support 2
10-460 “V” Foot 4
10-545 Ski Plastic Plug 4
10-548 Hook Protector ( 4 - 3/8" L ) 2
10-712 Mounting Track 2
18-053 Spacer 6
15-2584 Front Crossbow 2
15-2594 Rear Crossbow 1
15-3003 Ladder Clamp Hasp 2
15-3004 Ladder Clamp Rear Hook 2
15-3005 Ladder Clamp Bar ( Driver Side ) 1
15-3006 Ladder Clamp Bar ( Passenger Side ) 1
15-3010 Ski ( Left ) 1
15-3011 Ski ( Right ) 1
15-4290 Front Hook 2
94-1009 Assembly Fastener Kit 1
96-1003 Install Fastener Kit 1
BILL OF MATERIALS
15-300615-3005
15-259415-2584
15-3011
15-3010
15-3004 15-429015-3003
10-460 10-545
10-149
10-548
10-712
18-053

For technical support, contact us at 1-800-565-5321 1525-FTR Installation Guide |REV. B3 | Page 4
94-1009 Fastener Kit Fastener Assembly
1.1.3 Fastener kits.
4×4×
#90-487 Carriage Bolt 5/16" × 3/4"
#98-123 Lock Washer
#94-105 Hex Nut
#98-117 Flat Washer
24×24×
#90-491 Carriage Bolt 5/16" × 1"
#98-123 Lock Washer
#94-105 Hex Nut
#98-117 Flat Washer
4×4×
#98-123 Lock Washer
#94-105 Hex Nut
#98-117 Flat Washer
2×2×
#90-491 Carriage Bolt 5/16" × 1"
#98-123 Lock Washer
#94-105 Hex Nut
#98-117 Flat Washer
#98-160 Spacer
# 90-487
4×4×
Carriage Bolt
5/16"-18 × 3/4"
SS304
# 90-491
26×26×
Carriage Bolt
5/16"-18 × 1"
SS304
# 98-117
Flat Washer
5/16", O.D 3/4"
SS18-8
34×34×
# 98-123
Lock Washer
Regular 5/16"
SS304
34×34×
# 94-105
Hex Nut
5/16"-18
SS316wax
34×34×
# 98-160 Spacer
SS18-8
2×2×

For technical support, contact us at 1-800-565-5321 1525-FTR Installation Guide |REV. B3 | Page 5
PHASE 1 – ASSEMBLY
1.2 LADDER RACK ASSEMBLY
1.2.1 Peel the backer off of the adhesive on the hook protector, then attach the hook protector
to the upper rear hook.
TOOLS
qKnife
REMOVE
2×
96 - 1003 Fastener Kit Fastener Assembly
# 98-117
14×14×
Flat Washer
5/16", OD 3/4"
SS18-8
# 98-123
14×14×
Lock Washer
5/16"
SS304
# 90-209
8×8×
Hex Bolt
5/16"-18 × 1"
SS304
# 94-150 Channel Nut
5/16"
8×8×
# 90-004
6×6×
Hex Bolt
M8-1.25 × 50mm
SS304
8×8×
#90-209 Hex Bolt 5/16" × 1"
#98-123 Lock Washer
#98-117 Flat Washer
#94-150 Channel Nut
6×6×
#90-004 Hex Bolt M8 × 50
#98-123 Lock Washer
#98-117 Flat Washer

For technical support, contact us at 1-800-565-5321 1525-FTR Installation Guide |REV. B3 | Page 6
1.2.2 Attach the rear hooks to the ladder clamps, with the pre-assembled hardware on the pivot bars.
TOOLS
qCordless Impact
q1/2" Socket
q1/2" Wrench
#90-225 Hex Bolt
5/16" - 18 × 2" SS304
#98-117 Flat Washer
#98-117 Flat Washer
#94-111 Lock Nut
HARDWARE USED
4× hardware is pre-assembled.

For technical support, contact us at 1-800-565-5321 1525-FTR Installation Guide |REV. B3 | Page 7
1.2.3 Slide carriage bolts on the bottom face of the crossbows.
DRIVER SIDE PASSENGER SIDE
8×8×
#90-491 Hex Bolt
5/16" × 1" SS304
#90-491 Hex Bolt
5/16" × 1" SS304
Rear crossbow
• Slide 2 pcs. of 3/4" carriage bolts.
• Slide 4 pcs. of 1" carriage bolts.
Rear crossbow
• Slide 2 pcs. of 3/4" carriage bolts.
• Slide 4 pcs. of 1" carriage bolts.
First Front crossbow
• Slide 4 pcs. of 1" carriage bolts.
First Front crossbow
• Slide 4 pcs. of 1" carriage bolts.
HARDWARE USED
2×
HARDWARE USED
2×
#90-487 Carriage Bolt
5/16" × 3/4" SS304
#90-487 Carriage Bolt
5/16" × 3/4" SS304
TIPS: Use tape to keep the bolts from sliding off.
NOTE: The track plug must be removed from the underneath of the crossbows, and reinstalled after
the feet have been installed in the nal position.

For technical support, contact us at 1-800-565-5321 1525-FTR Installation Guide |REV. B3 | Page 8
HARDWARE USED
16× hand-tighten the nuts.
Carriage bolts are already on
the crossbows.
#98-123 Lock Washer
#98-117 Flat Washer
#94-105 Hex Nut
1.2.4 Install the feet on the rst Front, and Rear Crossbows.
NOTE: The more slanted side of the V foot should be closer to the end of the crossbow.

For technical support, contact us at 1-800-565-5321 1525-FTR Installation Guide |REV. B3 | Page 9
1.2.5 Fasten the left and right ladder clamp assemblies to the Rear Crossbow.
HARDWARE USED
4×
Carriage bolts are already on
the crossbows.
#98-123 Lock Washer
#98-117 Flat Washer
#94-105 Hex Nut
TOOLS
qCordless Impact q1/2" Socket
qTape Measure qMarker
12 - 3/4"

For technical support, contact us at 1-800-565-5321 1525-FTR Installation Guide |REV. B3 | Page 10
1.2.6 • Pull out the 14.5" track plug on the passenger side of the rst front crossbow and
the driver side of the adjustable front crossbow.
• Loosen the pre-assembled hardware on the front hooks and slide the hooks onto the
front crossbows to the position shown below.
• Cut the track plug, then attach it back to the crossbows.
8.5"
Tighten the nuts just to hold the front
hook for adjustment.
HARDWARE USED
4× hardware is pre-assembled.
#98-123 Lock Washer
#98-117 Flat Washer
#90-491 Carriage Bolt 5/16" × 1"
#94-105 Hex Nut
TOOLS
qMarker
qCutter

For technical support, contact us at 1-800-565-5321 1525-FTR Installation Guide |REV. B3 | Page 11
1.2.7 Install the left and right Skis to the end brackets of the front crossbow.
HARDWARE USED
4×
Carriage bolts are already on
the ski.
#98-123 Lock Washer
#98-117 Flat Washer
#94-105 Hex Nut
TOOLS
qCordless Impact
q1/2" Socket

For technical support, contact us at 1-800-565-5321 1525-FTR Installation Guide |REV. B3 | Page 12
Tighten the nuts just to hold the 2nd
front crossbow for adjustment.
HARDWARE USED
4× hand-tighten the nuts.
#98-123 Lock Washer
#98-117 Flat Washer
#90-491 Carriage Bolt 5/16" × 1"
#94-105 Hex Nut
1.2.8 Install the adjustable front crossbow to the left and right Skis.

For technical support, contact us at 1-800-565-5321 1525-FTR Installation Guide |REV. B3 | Page 13
HARDWARE USED
4× hand-tighten the nuts.
#98-123 Lock Washer
#98-117 Flat Washer
#90-491 Carriage Bolt 5/16" × 1"
#94-105 Hex Nut
1.2.9 After assembling the third crossbow attach the third crossbow to the skis.
NOTE: If you have a third crossbow, stop here and open the third crossbow box and follow the installation
guide to assemble the third crossbow.
THIRD CROSSBOW
NOTE: Don’t do this step if you don’t have the third crossbow.
Use the assembly fastener kit of the
third crossbow.

For technical support, contact us at 1-800-565-5321 1525-FTR Installation Guide |REV. B3 | Page 14
1.2.10 Loosen the pre-assembled hardware on the ladder clamp hasps, slide the hasps on the ski to the
position shown below, and tighten the nuts.
THIRD CROSSBOW
15 - 1/2"
HARDWARE USED
4× hardware is pre-assembled.
#98-123 Lock Washer
#98-117 Flat Washer
#90-487 Carriage Bolt 5/16" × 3/4"
#94-105 Hex Nut
TOOLS
qCordless Impact
q1/2" Socket
qTape Measure
qMarker

For technical support, contact us at 1-800-565-5321 1525-FTR Installation Guide |REV. B3 | Page 15
1.2.11 Slide 3pcs. of carriage bolts on the rear end of the each ski, then attach end plugs on
both ends of the skis.
end plug
end plug
THIRD CROSSBOW
HARDWARE USED
6×
#90-491 Carriage Bolt
5/16" × 1" SS304
TOOLS
qMallet
end plug

For technical support, contact us at 1-800-565-5321 1525-FTR Installation Guide |REV. B3 | Page 16
TOOLS
qCordless Impact
q1/2" Socket
HARDWARE USED
4×
#98-123 Lock Washer
#98-117 Flat Washer
#94-105 Hex Nut
2×
#98-123 Lock Washer
#98-160 Spacer
#98-117 Flat Washer
#94-105 Hex Nut
Carriage bolts are already on
the ski.
Carriage bolts are already on
the ski.
1.2.12 Install the Rear Crossbow to the skis with the clamp handle supports, aligning the rear surface of the
crossbow brackets to the rear surface of the skis.
THIRD CROSSBOW

For technical support, contact us at 1-800-565-5321 1525-FTR Installation Guide |REV. B3 | Page 17
PHASE 2 – INSTALLATION
2.1 MOUNTING TRACKS INSTALLATION
2.1.1 • Remove existing plugs on the vehicle roof holes.
• Use a tap ( M8 - 1.25 ) to remove the excess dirt/paint in the holes of the van.
• Apply a bead of silicone around the bolts and holes, then fasten the tracks to the roof.
TOOLS
qCordless Impact
q13mm Socket
FASTENERS USED
6×
#90-004 Hex Bolt M8 × 50
#98-123 Lock Washer
#98-117 Flat Washer

For technical support, contact us at 1-800-565-5321 1525-FTR Installation Guide |REV. B3 | Page 18
PHASE 2 – INSTALLATION
2.2 LADDER RACK INSTALLATION
2.2.1 Position the Ladder Rack ( minimum two persons ) on the vehicle so that the feet are on the tracks.
NOTE: If you do not have a hoist, lift the ladder rack onto the roof manually.
Ladder Rack

For technical support, contact us at 1-800-565-5321 1525-FTR Installation Guide |REV. B3 | Page 19
2.2.2 While making sure the crossbows are parallel to each other, slide the rack to the appropriate position,
then attach all the “V” feet to the mounting tracks.
NOTE: •If you have a third crossbow, center the third crossbow between the front and rear crossbows.
• Use the third crossbow install faster kit for the third crossbow feet installation.
FASTENERS USED
8×
TOOLS
qRatchet
q1/2" Socket
qTape Measure
#90-209 Hex Bolt 5/16" × 1"
#98-123 Lock Washer
#98-117 Flat Washer
#94-150 Channel Nut

For technical support, contact us at 1-800-565-5321 1525-FTR Installation Guide |REV. B3 | Page 20
2.2.3 Center the crossbows on the vehicle, then tighten all the “V” feet to the crossbows.
TOOLS
qRatchet
q1/2" Socket
NOTE: If you have a third crossbow, center the third crossbow between the front and rear crossbows.