Ranger design 1530-FTL User manual

INSTALLATION GUIDE
1530-FTL Double Clamp Ladder Rack
Long Ford Transit 148" and 148" Ext Wheelbase ( Aluminum )

QUICK START GUIDE
REQUIRED ITEMS
2
PERSONS
q1.1 Setup...............................................................................................................................................
q1.2 Ladder Rack Assembly....................................................................................................................
3 - 5
5 - 15
q2.1 Mounting Tracks Installation............................................................................................................
q2.2 Ladder Rack Installation..................................................................................................................
q2.3 Note.................................................................................................................................................
16
17 - 20
21
Phase 1 - Assembly
Phase 2 - Installation
NOTE: Use Sawhorses if possible, or use the box as a at protective surface on the ground or table.
qCordless Impact
qRatchet
qTape Measure
qMarker
qLadder
qCutter
q1/2" Socket
q13mm Socket
qSawhorse ( Optional )
qBox
qKnife
q1/2" Wrench
qSilicone

For technical support, contact us at 1-800-565-5321 1530-FTL Installation Guide |REV. C1 | Page 3
PHASE 1 – ASSEMBLY
1.1 SETUP
1.1.1 Unpack components; compare with the bill of materials.
1.1.2 Verify all parts are present.
Item No. Description Qty.
10-149 Clamp Handle Support 2
10-460 “V” Foot 4
10-545 Ski Plastic Plug 4
10-548 Hook Protector ( 4 - 3/8" L ) 2
10-702 Mounting Track 2
18-053 Spacer 8
15-3003 Ladder Clamp Hasp 2
15-3004 Ladder Clamp Rear Hook 2
15-3005 Ladder Clamp Bar ( Driver Side ) 1
15-3006 Ladder Clamp Bar ( Passenger Side ) 1
15-3010 Ski ( Left ) 1
15-3011 Ski ( Right ) 1
15-3125 Rear Crossbow 1
15-3130 Front Crossbow 1
15-4290 Front Hook 2
94-1012 Assembly Fastener Kit 1
96-1004 Install Fastener Kit 1
15-300615-3005
15-3011
15-3010
15-3004 15-429015-3003
10-460 10-545
10-149
10-548
15-3125
15-3130
10-702
18-053

For technical support, contact us at 1-800-565-5321 1530-FTL Installation Guide |REV. C1 | Page 4
94-1012 Fastener Kit Fastener Assembly
1.1.3 Fastener kits.
4×4×
#90-487 Carriage Bolt 5/16" × 3/4"
#98-123 Lock Washer
#94-105 Hex Nut
#98-117 Flat Washer
20×20×
#90-491 Carriage Bolt 5/16" × 1"
#98-123 Lock Washer
#94-105 Hex Nut
#98-117 Flat Washer
4×4×
#98-123 Lock Washer
#94-105 Hex Nut
#98-117 Flat Washer
2×2×
#90-491 Carriage Bolt 5/16" × 1"
#98-123 Lock Washer
#94-105 Hex Nut
#98-117 Flat Washer
#98-160 Spacer
# 90-487
4×4×
Carriage Bolt
5/16"-18 × 3/4"
SS304
# 90-491
22×22×
Carriage Bolt
5/16"-18 × 1"
SS304
# 98-117
Flat Washer
5/16", O.D 3/4"
SS18-8
30×30×
# 98-123
Lock Washer
Regular 5/16"
SS304
30×30×
# 94-105
Hex Nut
5/16"-18
SS316wax
30×30×
# 98-160 Spacer
SS18-8
2×2×

For technical support, contact us at 1-800-565-5321 1530-FTL Installation Guide |REV. C1 | Page 5
PHASE 1 – ASSEMBLY
1.2 LADDER RACK ASSEMBLY
1.2.1 Peel the backer off of the adhesive on the hook protector, then attach the hook protector
to the upper rear hook.
TOOLS
qKnife
REMOVE
2×
96 - 1004 Fastener Kit Fastener Assembly
# 98-117
16×16×
Flat Washer
5/16", OD 3/4"
SS18-8
# 98-123
16×16×
Lock Washer
5/16"
SS304
# 90-209
8×8×
Hex Bolt
5/16"-18 × 1"
SS304
# 94-150 Channel Nut
5/16"
8×8×
# 90-669
8×8×
Hex Bolt
M8-1.25 × 40mm
SS304
8×8×
#90-209 Hex Bolt 5/16" × 1"
#98-123 Lock Washer
#98-117 Flat Washer
#94-150 Channel Nut
8×8×
#90-004 Hex Bolt M8 × 50
#98-123 Lock Washer
#98-117 Flat Washer

For technical support, contact us at 1-800-565-5321 1530-FTL Installation Guide |REV. C1 | Page 6
1.2.2 Attach the rear hooks to the ladder clamps, with the pre-assembled hardware on the pivot bars.
TOOLS
qCordless Impact
q1/2" Socket
q1/2" Wrench
#90-225 Hex Bolt
5/16" - 18 × 2" SS304
#98-117 Flat Washer
#98-117 Flat Washer
#94-111 Lock Nut
HARDWARE USED
4× hardware is pre-assembled.

For technical support, contact us at 1-800-565-5321 1530-FTL Installation Guide |REV. C1 | Page 7
1.2.3 Slide carriage bolts on the bottom face of the crossbows.
DRIVER SIDE PASSENGER SIDE
8×8×
#90-491 Hex Bolt
5/16" × 1" SS304
#90-491 Hex Bolt
5/16" × 1" SS304
Rear crossbow
• Slide 2 pcs. of 3/4" carriage bolts.
• Slide 4 pcs. of 1" carriage bolts.
Rear crossbow
• Slide 2 pcs. of 3/4" carriage bolts.
• Slide 4 pcs. of 1" carriage bolts.
Front crossbow
• Slide 4 pcs. of 1" carriage bolts.
Front crossbow
• Slide 4 pcs. of 1" carriage bolts.
HARDWARE USED
2×
HARDWARE USED
2×
#90-487 Carriage Bolt
5/16" × 3/4" SS304
#90-487 Carriage Bolt
5/16" × 3/4" SS304
TIPS: Use tape to keep the bolts from sliding off.
NOTE: The track plug must be removed from the underneath of the crossbows, and reinstalled after
the feet have been installed in the nal position.

For technical support, contact us at 1-800-565-5321 1530-FTL Installation Guide |REV. C1 | Page 8
1.2.4 Install the feet on the front, and rear crossbows.
NOTE: The more slanted side of the V foot should be closer to the end of the crossbow.
HARDWARE USED
16× hand-tighten the nuts.
Carriage bolts are already on
the crossbows.
#98-123 Lock Washer
#98-117 Flat Washer
#94-105 Hex Nut

For technical support, contact us at 1-800-565-5321 1530-FTL Installation Guide |REV. C1 | Page 9
1.2.5 Fasten the ladder clamp assemblies to the rear crossbow.
HARDWARE USED
4×
Carriage bolts are already on
the crossbows.
#98-123 Lock Washer
#98-117 Flat Washer
#94-105 Hex Nut
TOOLS
qCordless Impact
q1/2" Socket
qTape Measure
qMarker
12 - 3/4"

For technical support, contact us at 1-800-565-5321 1530-FTL Installation Guide |REV. C1 | Page 10
1.2.6 • Pull out the 14.5" track plug on both ends of the front crossbow.
• Loosen the pre-assembled hardware on the front hooks and slide the hooks onto the
front crossbow to the position shown below.
• Cut the track plug, then attach it back to the crossbow.
8.5"
Tighten the nuts just to hold the front
hook for adjustment.
HARDWARE USED
4× hardware is pre-assembled.
#98-123 Lock Washer
#98-117 Flat Washer
#90-491 Carriage Bolt 5/16" × 1"
#94-105 Hex Nut
TOOLS
qMarker
qCutter

For technical support, contact us at 1-800-565-5321 1530-FTL Installation Guide |REV. C1 | Page 11
1.2.7 Install the left and right Skis to the end brackets of the front crossbow.
HARDWARE USED
4×
Carriage bolts are already on
the ski.
#98-123 Lock Washer
#98-117 Flat Washer
#94-105 Hex Nut
TOOLS
qCordless Impact
q1/2" Socket

For technical support, contact us at 1-800-565-5321 1530-FTL Installation Guide |REV. C1 | Page 12
1.2.8 After assembling the third crossbow attach the third crossbow to the skis.
NOTE: If you have a third crossbow, stop here and open the third crossbow box and follow the installation
guide to assemble the third crossbow.
NOTE: Don’t do this step if you don’t have the third crossbow.
HARDWARE USED
4× hand-tighten the nuts.
#98-123 Lock Washer
#98-117 Flat Washer
#90-491 Carriage Bolt 5/16" × 1"
#94-105 Hex Nut
Use the assembly fastener kit of the
third crossbow.

For technical support, contact us at 1-800-565-5321 1530-FTL Installation Guide |REV. C1 | Page 13
1.2.9 Loosen the pre-assembled hardware on the ladder clamp hasps, slide the hasps on the ski to the
position shown below, and tighten the nuts.
THIRD CROSSBOW
15 - 1/2"
HARDWARE USED
4× hardware is pre-assembled.
#98-123 Lock Washer
#98-117 Flat Washer
#90-487 Carriage Bolt 5/16" × 3/4"
#94-105 Hex Nut
TOOLS
qCordless Impact
q1/2" Socket
qTape Measure
qMarker

For technical support, contact us at 1-800-565-5321 1530-FTL Installation Guide |REV. C1 | Page 14
1.2.10 Slide 3pcs. of carriage bolts on the rear end of the each ski, then attach end plugs on
both ends of the skis.
THIRD CROSSBOW
HARDWARE USED
6×
#90-491 Carriage Bolt
5/16" × 1" SS304
TOOLS
qMallet
end plug

For technical support, contact us at 1-800-565-5321 1530-FTL Installation Guide |REV. C1 | Page 15
TOOLS
qCordless Impact
q1/2" Socket
HARDWARE USED
4×
#98-123 Lock Washer
#98-117 Flat Washer
#94-105 Hex Nut
2×
#98-123 Lock Washer
#98-160 Spacer
#98-117 Flat Washer
#94-105 Hex Nut
Carriage bolts are already on
the ski.
Carriage bolts are already on
the ski.
1.2.11 Install the Rear Crossbow to the skis with the clamp handle supports, aligning the rear surface of the
crossbow brackets to the rear surface of the skis.
THIRD CROSSBOW

For technical support, contact us at 1-800-565-5321 1530-FTL Installation Guide |REV. C1 | Page 16
PHASE 2 – INSTALLATION
2.1 MOUNTING TRACKS INSTALLATION
Mounting Track Orientation
REAR FRONT
use use use use
TOOLS
qCordless Impact
q13mm Socket
FASTENERS USED
8×
#90-004 Hex Bolt M8 × 50
#98-123 Lock Washer
#98-117 Flat Washer
2.1.1 • Remove existing plugs on the vehicle roof holes.
• Use a tap ( M8 - 1.25 ) to remove the excess dirt/paint in the holes of the van.
• Apply a bead of silicone around the bolts and holes, then fasten the tracks to the roof.

For technical support, contact us at 1-800-565-5321 1530-FTL Installation Guide |REV. C1 | Page 17
PHASE 2 – INSTALLATION
2.2 LADDER RACK INSTALLATION
2.2.1 Position the Ladder Rack ( minimum two persons ) on the vehicle so that the feet are on the tracks.
NOTE: If you do not have a hoist, lift the ladder rack onto the roof manually.
Ladder Rack

For technical support, contact us at 1-800-565-5321 1530-FTL Installation Guide |REV. C1 | Page 18
FASTENERS USED
8×
TOOLS
qRatchet
q1/2" Socket
qTape Measure
#90-209 Hex Bolt 5/16" × 1"
#98-123 Lock Washer
#98-117 Flat Washer
#94-150 Channel Nut
2.2.2 While making sure the crossbows are parallel to each other, slide the rack to the appropriate position,
then attach all the “V” feet to the mounting tracks.
NOTE: •If you have a third crossbow, center the third crossbow between the front and rear crossbows.
• Use the third crossbow install faster kit for the third crossbow feet installation.

For technical support, contact us at 1-800-565-5321 1530-FTL Installation Guide |REV. C1 | Page 19
TOOLS
qRatchet
q1/2" Socket
2.2.3 Center the crossbows on the vehicle, then tighten all the “V” feet to the crossbows.
NOTE: If you have a third crossbow, center the third crossbow between the front and rear crossbows.

For technical support, contact us at 1-800-565-5321 1530-FTL Installation Guide |REV. C1 | Page 20
1"
TOOLS
qCordless Impact
q1/2" Socket
front hook
rear hook
When the rear hook touches the ladder,
the handle should be 1" below the ladder
clamp hasp.
Now adjust the front hook to be snug against
the ladder rung and tighten the bolts on the
front crossbow.
2.2.4 Ladder Rack adjustment for extention ladder.
NOTE: • Do this step on both sides.
•The ladder cannot extend beyond the rear bumper of the vehicle.
IMPORTANT: • After installation is complete, cut the track plug underneath the crossbows to ll all the
unused space.
• Place the ladder rack warning label on a visible area, recommended on a partition.