Ranger design C24-DH User manual

INSTALLATION GUIDE
C24-DH STRAIGHT PARTITION
Sprinter Partition ( Walk-Through, Steel )

For technical support, contact us at 1-800-565-5321 C24-DH Installation Guide |REV. D2 | Page 2
QUICK START GUIDE
REQUIRED ITEMS
2
PERSONS
qCordless Impact
qCordless Drill
qCutter
qMallet
qPlusnut Tool
qTape Measure
qT40 Torque Bit
q3/8" Drill Bit
q7/16" Socket
q1/2" Socket
q9/16" Wrench
q3/16" Driver Bit
q1.1 Setup...................................................................................................................................................
q1.2 Partition assembly...............................................................................................................................
3 - 4
5
Phase 1 - Assembly
q2.1 Tips on how to attach a plusnut..........................................................................................................
q2.2 Vehicle preparation..............................................................................................................................
q2.3 Straight partition installation................................................................................................................
6
7 - 9
10 - 13
Phase 2 - Installation

For technical support, contact us at 1-800-565-5321 C24-DH Installation Guide |REV. D2 | Page 3
PHASE 1 – ASSEMBLY
1.1 SETUP
1.1.2 Verify all parts are present.
Item No. Description Qty.
30-052 Floor Bracket 1
30-057 Top Bracket 1
30-070 Passenger Side Panel 1
30-071 Driver Side Panel 1
30-500 Edge Trim ( QTY in Inches ) 45
70-350 Grab Handle 1
79-932 Warning Label ( Bilingual ) 1
94-3001 Assembly Fastener Bag 1
94-6093 Assembly Fastener Bag 1
96-3000 Installation Fastener Bag 1
1.1.1 Unpack components; compare with the bill of materials.
30-500
30-057
30-052
30-071 30-070
70-350

For technical support, contact us at 1-800-565-5321 C24-DH Installation Guide |REV. D2 | Page 4
1.1.3 Identify the Assembly and Installation fastener bags.
Flat Washer
5/16", 7/8" OD
ZINC
# 98-116
8×
Hex Bolt
5/16"-18 × 1/2"
GR-5 ZINC
# 90-200
4×
Serrated Nut
5/16"-18
ZINC
# 94-116
8×
Hex Bolt
5/16"-18 × 3/4"
GR-5 ZINC
# 90-204
4×
4×
4×
#90-200 Hex Bolt 5/16" × 1/2"
#98-116 Flat Washer
#94-116 Serrated Nut
#90-204 Hex Bolt 5/16" × 3/4"
#98-116 Flat Washer
#94-116 Serrated Nut
94-3001 Fastener Bag Hardware Assembly
Hex Bolt
1/4"-20 × 1-1/4"
GR-5 ZINC
# 90-118
15×
Flat Washer
1/4", 3/4" OD
ZINC
# 98-112
15×
Plusnut .250
# 94-130
15×
Lock Washer
Regular 1/4"
ZINC
# 98-118
15×
15×
#90-118 Hex Bolt 1/4" × 1-1/4"
#98-118 Lock Washer
#98-112 Flat Washer
#94-130 Plusnut .250
96-3000 Fastener Bag Hardware Assembly
94-6093 Fastener Bag Hardware Assembly
Serrated Nut
1/4"-20
ZINC
# 94-112
2×
# 90-893 Cap Screw
1/4" × 3/4"
2× 2×
#90-893 Cap Screw 1/4" × 3/4"
#94-112 Serrated Nut

For technical support, contact us at 1-800-565-5321 C24-DH Installation Guide |REV. D2 | Page 5
PHASE 1 – ASSEMBLY
1.2 PARTITION ASSEMBLY
1.2.1 Remove all the PVC from all the parts, then attach the grab handle on the passenger side panel.
1.2.2 Attach the edge trims on these locations.
TOOLS
qCordless Impact
q3/16" Driver Bit
HARDWARE USED
2×
#90-893 Cap Screw 1/4" × 3/4"
#94-112 Serrated Nut
TOOLS
qMallet
qCutter

For technical support, contact us at 1-800-565-5321 C24-DH Installation Guide |REV. D2 | Page 6
PHASE 2 – INSTALLATION
2.1 TIPS ON HOW TO ATTACH A PLUSNUT
FORWARD REVERSE
TIPS: Put the plusnut on the plusnut gun, then attach the plusnut in the hole by turning the gun forward until the
plusnut locks, then remove the gun by turning in reverse.
2.1.1 Attach the plusnut using the plusnut gun.
2.1.2 Attach the plusnut using the 6490 plusnut tool.
6490 HARDWARE USED
Flat washer 1/4"
Flat washer 1/4" BS × 3/4" OD
TOOLS
qCordless Impact
q7/16" Socket
q9/16" Wrench
TIPS STEP 1:
Assemble the 6490 plusnut tool with the hardware needed,
plusnut and the 9/16" wrench as shown.
FORWARD REVERSE
TIPS STEP 2:
Attach the plusnut in the hole by turning
the bolt forward using an impact with a
7/16" socket until the plusnut locks, then
remove the bolt by turning the impact in
reverse.
NOTE: The hardware used for the 6490 plusnut tool is not included in the fastener bag.
The 6490 plusnut tool can be ordered separately upon demand at no charge.

For technical support, contact us at 1-800-565-5321 C24-DH Installation Guide |REV. D2 | Page 7
2.2.1 Preparation.
PHASE 2 – INSTALLATION
2.2 VEHICLE PREPARATION
TOOLS
qCordless Impact
q1/2" Socket
HARDWARE USED
4×
#90-200 Hex Bolt 5/16" × 1/2"
#98-116 Flat Washer
#94-116 Serrated Nut
Lift the driver and passenger side panels inside the van, put the
panels in place, then attach the top bracket on the driver and
passenger side panels.

For technical support, contact us at 1-800-565-5321 C24-DH Installation Guide |REV. D2 | Page 8
2.2.2 Attaching plusnuts.
TOOLS
qPlusnut Tool
# 94-130
Plusnut .250
HARDWARE USED
15×
Attach plusnuts in the 15 holes.
TOOLS
qCordless Drill
q3/8" Drill Bit or Step Drill
NOTE: Check if the holes of the partition align with the holes of the van.
Enlarge all the holes in the van that are aligned with the holes
of the partiton using 3/8" drill bit or step drill.
NOTE: Make new holes in the van if the holes are not aligned
with the holes of the partition.

For technical support, contact us at 1-800-565-5321 C24-DH Installation Guide |REV. D2 | Page 9
2.2.3 Floor preparation.
Remove the two D-rings in the pillars, for
re-use.
TOOLS
qCordless Impact
qT40 Torque Bit

For technical support, contact us at 1-800-565-5321 C24-DH Installation Guide |REV. D2 | Page 10
PHASE 2 – INSTALLATION
2.3 STRAIGHT PARTITION INSTALLATION
2.3.1 Floor bracket installation.
Attach the oor bracket to the oor
re-using the 2 D-ring bolts.
HARDWARE USED
2×
Use the D-ring bolt
TOOLS
qCordless Impact
qT40 Torque Bit