real living OAKMONT GB19-517 User manual

ASSEMBLY INSTRUCTION
ITEM# GB19-517 / GB19-517-NAVY
SKU# 810414475 / 810460101
OAKMONT ALL WEATHER WICKER ROCKER
CARE & MAINTENANCE
DO NOT RETURN THIS PRODUCT TO THE STORE. FOR MISSING PARTS OR QUESTIONS TO THIS PRODUCT PLEASE CALL US AT 1-888-733-8169 OR
EMAIL US AT [e-mail] OR customers[email protected] OR customers[email protected]
IMPORTANT:
Please read all the instructions and warnings before assembling. In order to make the whole product adjust to the best, please install all the screws on the product before
fully tighten, and tighten all the screws after adjusting the product which can stand on the floor even.
WARNING:
Use the correct screws as indicated. All screws should be hand tight untill the complete piece is assembled ( This will make the assembly
process much easier ). Once the piece is fully assembled, then go back and tight all screws with provided tool.
STAIN RESISTANT CUSHIONS CARE —— KEEP THE CUSHIONS IN STORAGE IN RAINING DAY.
SPILLS: Immediately wipe up the spill using a white damp cloth. Repeat process if necessary until stain is gone. Allow cushion to air dry.
FABRIC CARE: Hand wash cold, non-chlorine bleach when needed, lay flat to dry. Cool iron if necessary. Do not dry clean.
ALL WEAHTER WICKER PRODUCT CARE
Before using, clean the product completely with a soft dry towel. When not in use, wipe free of any dirt or loose objects, wash with a mild solution of soap and water,
rinse thoroughly and dry completely. Do not use strong detergent or abrasive cleaners. Over time nuts and screws can loosen. Occasinally, check nuts and screws on the
rocker, re-tighten if necessary.
Keep all children and pets away from assembly area. Children and pets should be supervised when they are in the area of the product construction.
Keep assembly area at leat 6 feet from any obstruction such as a fence, garage, house, overhanging branches, laundry line or electrical wires.
Some parts may contain sharp edges. When assembling and using this product, basic safety precautions should always be followed to reduce the risk of personal injury
and damage to the product. Please read all instructions before assembly and use.
The rocker is not to be used for standing purposes and will not function as a stool or step-ladder. Use on even surfaces only.
The rocker is not a toy. Proper use of the rocker is for single person seating only. Rocker tested for use at weight of 250 lb (113.4 kg).
Improper use of this product or failure to use as directed may result in injury. Not intended for commercial use.

NO. Part Qty Image NO. Part Qty Image
A1 Left Arm 1A2 Right Arm 1
BChair Back 1 C Seat Panel 1
DBig Washer 10 E Screw(φ6x15mm) 8
FScrew(φ6x35mm) 2 G Allen Wrench 1
H Runner 2 I Tapping Screw 4
JSmall Washer 4
PARTS LIST
STEP 1
Do not fully tighen now.
STEP 2
Do not fully tighen now.
STEP 3
Do not fully tighen now.
G
E
D
A1
DE
DE
B
ED
G
A2

STEP 4
Do not fully tighen now.
STEP 5
Attach runners (H) to assembled rocker and secure by using
Tapping screws (I) and small washers (J). Please make sure
the direction of runner is correct.
STEP 6
Verify the alignment and adjust, fully tighten all the screws
now. Put cushions on the rocker. The rocker is assembled.
WARNING:
THIS ROCKER IS NOT A TOY. DON'T OVER-
ROCK THE ROCKER. IT MAY MAKE THE
ROCKER TIP OVER AND RESULT IN INJURY.