real living ZS007R User manual

ITEM#: ZS007R/ZS007B/ZS007W
SKU#: 810343918/810534674/810534673
Need help? We are here for you!
www.biglots.com/help/contact-us
RUSTIC 2 DRAWER DESK
ASSEMBLY INSTRUCTION

Read all instructions before starting
Clear a flat covered space to assemble
We recommend two people for assembly.
Note that hardware required is provided for every step
Pay attention to orientation
Letter of the part corresponds to a sticker on the product
Number of the hardware corresponds to its number in the package
Helpful hints provided along the way
Note: This product includes a tube of glue. The glue is not required for
assembly but can help the products durability and structural soundness and
extend the life of the product. Please follow these instructions to use the
glue. It is important to note that if glue is used for assembly, the product
will no longer have the ability to be disassembled.
1. Place a small dab of glue into the hole just prior to placing the wood
dowel into position. DO NOT fill the hole with glue.
2. Wipe up any excess glue up with a damp paper towel.
3. Repeat this for all holes where a wood dowel is inserted.
Hint: If to much glue is placed into a hole, Q-tip can be used to remove
excess glue and transfer it the next hole. Be certain to wipe up any excess
glue immediately with a damp paper towel.
Regularly check hardware and tighten if necessary
GENERAL BEST PRACTICES FOR ASSEMBLY:
MAINTENANCE:
CARE AND CLEANING:
Clean periodically by wiping the product with a soft clean cloth
DO NOT use abrasive chemicals for cleaning.

x1
LEFT LEG RIGHT LEG BACK SUPPORT BAR
FRONT SUPPORT BAR REAR RIGHT SUPPORT BAR REAR LEFT SUPPORT BAR
BOTTOM PANEL TOP PANEL RIGHT SIDE PANEL
LEFT SIDE PANEL BACK PANEL MIDDLE PANEL
DRAWER FRONT PANEL LEFT SIDE PANEL OF DRAWER RIGHT SIDE PANEL OF DRAWER
x1x1
x1x1x1
x1x1x1
x1x1x1
x2x2x2
A B C
F
D E
H
JL
MNO
I
K
PARTS LIST
G

BACK PANEL OF DRAWER BOTTOM PANEL OF DRAWER
x9
CAM CAM LOCK
x25
PHILLIPS SCREW
x2
UMBRELLA HEAD BOLT
x20
WOOD DOWEL
x1
GLUE
x12
ALLEN BOLT
x4
ALLEN BOLT
x1
ALLEN WRENCH
x2
HANDLE
x2x2
x9
P
134
678
10
5
9
Q
PARTS LIST
HARDWARE LIST
2

x7x6x1
Insert cam (1) into top panel (H) using a Phillips screwdriver (not
provided) and full tighten. Insert Wood dowel (5) into top panel (H) using
glue (6) as directed in GENERAL BEST PRACTICES section of page 2.
Assembled View
156
1
H
1
1
1
5
5
5
55
5
6
6
6
6
1
16
STEP 1
1

x4x1
Assemble left side panel (I) and right side panel (J) to back panel (K)
using wood dowels (5) and glue (6) as directed in GENERAL BEST
PRACTICES section of page 2 .
Assembled View
56
I
6
5
6
5
K
J
STEP 2

x7
Insert cam lock (2) into holes of side panel (I), side panel (J) and back
panel (K). Apply small dab of glue to top of wood dowels in top panel (H).
Carefully place assembled side and back panels (I), (J) and (K) onto top
panel (H) and tighten cam locks (2) with Phillips screwdriver (not provided
). Wipe up any visible glue with a damp paper towel.
Assembled View
2
2
2
2
2
2
H
STEP 3
KJ
I

1
1
2
2
55
6
1
x2
5
x2
6
x1
Insert cam (1) into top panel (H) using Phillips screwdriver (not provided ).
Insert wood dowel (5) into top panel (H) using glue (6) as directed in
GENERAL BEST PRACTICES section of page 2. Insert cam lock (2) into holes
of middle panel (L). Apply small dab of glue to top of wood dowels in top
panel (H). Carefully place middle panel (L) onto top panel (H). Tighten cam
locks (2) with Phillips screwdriver (not provided). Wipe up any visible glue
with a damp paper towel.
Assembled View
6L
STEP 4
x2
2
H

x9x8x1
Insert wood dowel (5) into side and back panels (I), (J) and (K) using glue
(6) as directed in GENERAL BEST PRACTICES section of page 2. Apply small
dab of glue to top of wood dowels in side and back panels (I), (J) and (K)
using glue (6). Carefully place bottom panel (G) onto side and back panels
(I), (J) and (K). Secure bottom panel in place with Phillips screw (3) using
Phillips screwdriver (not provided). Fully tighten all screws. Wipe up any
visible glue with a damp paper towel.
Assembled View
3
3
5
6
5
65
6
5
6
56
G
G
STEP 5
I
J
K

x8x1
Note: The side of back support bar (C)
with the holes should be facing down
Assemble front support bar (D) & back support bar (C) on left leg
(A) and right leg (B) with Allen bolts (7) by using Allen wrench (9).
Assembled View
C
9
7
A
7
7
7
7
7
D
STEP 6
7
B
7
9

x4x1
Assemble rear right cross bar (E) and rear left cross bar (F) with Allen
bolts (7) by using Allen wrench (9).
Assembled View
7
79
7
F
E
7
7
C
STEP 7
7
9

x4x1
Carefully place the assembled metal frame onto the bottom panel (G)
and attach with Allen bolts (8) using Allen wrench (9).
Assembled View
89
8
8
8
8
STEP 8
8
9

x4
Assemble right side panel of drawer (O) and left side panel of
drawer (N) to back panel of drawer (P) with Phillips screws (3) using
Phillips screwdriver (not provided).
Assembled View
3
3
3
PO
N
PO
N
STEP 9

x4x1x1
Slide bottom panel of drawer (Q) into grooves of assembled side and back
panels of drawer. Attach drawer front panel (M) to left and right side panels
of drawer using Phillips screws (3) and Phillips screwdriver (not provided).
Repeat STEPS 9 through 10 to
assemble remaining drawer.
Assembled View
Attach handle (10) to drawer front panel (M) with umbrella head bolts
(4) using Phillips screwdriver (not provided).
3
3
M
Q
10
4
10 4
STEP 10
3

STEP 11
Please make sure the bead is
at the front end of slide.
PLEASE NOTE: The drawers should slide
completely into desk. If drawers jam or bind,
remove them, realign the glides and reinsert.
Align the glides on the drawers with
glides in the assembled drawer box.
carefully insert the drawer. Note: If
the drawer needs to be removed,
depress the plastic levers on the
drawer glides and hold to release
the drawer.
Assembly is now complete.