real living LYNNDALE PERGOLA A106008800 User manual

TM
LYNNDALE PERGOLA
ASSEMBLY INSTRUCTIONS
ITEM#: A106008800 / A106008801 / A106008802
SKU#: 810500178 / 810500179 / 810500180
Need help? We are here for you! 1(866)578 – 6569 24/7 • Toll Free

WARRANTY:
WARNINGS:
MAINTENANCE
GENERAL BEST PRACTICES FOR ASSEMBLY:
WHAT IS COVERED?
The limited warranty is extended to theoriginal purchaser and applies tomaterial and manufacturer’s defectprovided
the item is maintained with care and used only for personal, residential purposes.
Warranty: 1 Year
•Please read and understand this entire manual before attempting to assemble or install the product.
•Before beginning assembly of product, make sure allparts arepresent. Compare parts with packagecontents list and
hardware contents list.Ifany part is missing or damaged, do notattemptto assemble the product.
• The assembled pergola should be located at least 6 feet from any obstruction such as fence, garage, house, overhanging
branches, laundry lines or electrical wires.
•Some parts may containsharp edges. Wear protectivegloves ifnecessary,during assembly.
• This unit is heavy. For safety, do not assemble this item alone.TWO people are recommended for safe assembly.
•Check all nuts and bolts periodically for tightness and, when required, tighten them again.
•Pay attention to the parts orientation
•Install the pergola on level stableground.Stakes areprovided to secure the gazebo totheground.
•Snow mustbe cleared off regularly during snowydays.Removethe snow at the roof top whenit is thicker than 2 inches. In
order to avoid damage,use a plastic snow rake to remove excessive snow and ice buildup from roof and keep away from
falling debris.
• Any assembly or maintenance of the productmust be carried out by adults only.
•Please check your state and local regulations prior to purchasing. Some jurisdictions may require permits for installation and
use. Some special procedures may bevalid in your area.
•Keep all flame and heat sources away from the tent fabric. This tent is made with fabric that meets CPAI-84 specifications for
flame resistance. It is not fire proof. The fabric will burn if right in continuous contact with any flame source. The application of
any foreign substance to the tent fabric may render the flameresistant properties ineffective.
• For outdoor use only.
•An annual application of awater‐based stain or sealant is recommended to reduce weathering and extend the life of your
gazebo.
•Inspect all wood parts regularly for damageor deterioration. Remove/sand splinters and replace any wood parts that are
showing signs of structural damage. Note thatknots, small cracks and weathering are natural in anoutdoor wood product
and do not negatively affect the structural integrity of the gazebo.
•Keep instruction manual for future reference.
•Keep the original packaging tostore the pergola.
2/23

Label Part Number Description Qty Part Image
3/23
01
02
03
04
05
08
09
10
11
12
13
15
16
17
18
19
21

4/23
25
26
31
20
22
23
24
P006400017

5/23

How many people are needed for the installation
6/23

Assembled View:
7/23
Attached Post base (A) to
Screen(03/04/05) with Screw (H4).

Assembled View：
8/23
Attached Post base (A) to Small
post (09/08) with Screw (H4).

Assembled View:
9/23
Attached Post base (A) to Small
post (10/11) with Screw (H4).

Assembled View:
10/23
Attached Cross beam (12) and
Screen (13) to Screen (03/04) and
Small post (09/08) with Screw
(H6/H7).

Assembled View:
11/23
Attached Cross beam (12) and
Screen (13) to Screen (05) and
Small post (10/11) with Screw
(H6/H7).

Assembled View:
12/23
Attached the assembled screen to
the Big post (01/02) with Screw
(H5).

Assembled View:
13/23
Attached Cross beam(18/19) to
Small post (09/08/10/11) and Big
post (01/02) with Bolt (H3) and Flat
washer (H9), tighten with Wrench
(HW).

Assembled View:
14/23
Attached Arc beam(21) to Arc
beam(23) with Bolt (H2) and Flat
washer (H9), tighten with
Wrench (HW).

Assembled View:
15/23
Attached Support beam(24) to
Arc beam(21/23) with Screw
(H5), attached Brace (31) to Arc
beam(21/23) with Screw (H6),

Assembled View:
A
ssem
b
l
e
d
V
i
e
16/23
Attached assembled Arc beam to
Post with Bolt (H3) ,Screw (H8)
and Flat washer (H9).

Assembled View:
17/23
Attached Arc beam (20) to Arc
beam (22) with Bolt (H2) and Flat
washer (H9), attached Beam tail
(17) to Arc beam (20) and Arc
beam (22) with Screw (H6),

Assembled View:
18/23
Attached Connector panel (24) to
Arc beam (20) and Arc beam (22)
with Screw (H5), attached Brace
(31) to Arc beam(20/22) with
Screw (H6),

Assembled View:
19/23
Attached assembled Arc beam to
Post with Bolt (H3) ,Screw (H8)
and Flat washer (H9).

Assembled View:
20/23
Attached Short brace (15) and Long
brace (16 ) to post and Arc beam
with Screw (H5/H6)