real living OAKMONT User manual

TM
10x12 OAKMONT GAZEBO
ASSEMBLY INSTRUCTIONS
ITEM#: A101001700
SKU#:810500467
Need help? We are here for you! 1(866)578 – 6569 24/7 • Toll Free

•Please read and understand this entire manual before attempting to assemble or install the product.
• Before beginning assembly of product, make sure all parts are present. Compare parts with package contents list and
hardware contents list. If any part is missing or damaged, donot attempt to assemble the product.
• The assembled gazebo should be located at least 6 feet from any obstruction such as fence, garage, house, overhanging
branches, laundry lines or electrical wires.
• Some parts may contain sharp edges. Wear protective gloves if necessary, during assembly.
• This unit is heavy.For safety, do not assemble this item alone. Twopeopleare recommended for safe assembly.
•Check all nuts and bolts periodically for tightness and, when required, tighten them again.
•Pay attention to the parts orientation
• Install the gazebo on levelground.Stakes are provided to secure the gazebo to the ground.
• Do not assemble the gazebo on sandy, muddy or loose soil, as stakes do not have enough anchorage in these types of soil.
• If you wish to secure the gazebo to a wood deck or concrete surface, use anchors suited to these surfaces.
•Snow must becleared off regularly during snowy days.Remove the snow at the roof top when it is thicker than 2 inches. In orderto
avoid damage, use a plastic snow rake to remove excessive snow and ice buildup from roof and keep away from falling debris.
• Do not leave the gazebo where there is a risk of high wind, as possible damage will occur to the structure.
• Any assembly or maintenance of theproduct must be carried out by adults only.
• Please check your state and local regulations prior to purchasing. Some jurisdictions may require permits for installation and
use. Some specialprocedures may be valid in your area.
• Keep allflame and heat sources away from the tent fabric. This tent is made with fabric that meets CPAI-84 specifications for
flame resistance. It is notfire proof. The fabric will burn if right in continuous contact with any flame source. The application of
any foreign substance to the tent fabric may render the flameresistant properties ineffective.
• If any scratch paint, please touch up to prevent rusting
• For outdoor use only.
WARRANTY:
WARNINGS:
• Steel components for this gazebo are treated with rust inhibiting paint thatprotects it from rusting. However, due to the nature
of steel, surface oxidation (rusting) will occur if these protective coatings arescratched. This is not a defect and thus not covered
by the warranty.
• To minimize this condition, it is recommended to use care when assembling and handling the product to prevent scratching the
paint. Should any scratching or damage occur, it is recommended to cover the scratch immediately with rust inhibiting paint
(not included).
• Surface rust can also be easily removed with a very light application of regular cooking oil or WD-40. If surface oxidation (rusting)
occurs and if no measure is taken to prevent this, the oxidation may start dripping onto deck or patio and caused damaging
stains, whichmaybedifficult to remove. This can be prevented if the above-mentioned measures are taken to keep the product
from oxidizing.
• Do not use bleach, acid, or other abrasive cleaners on the roof or frame parts.
• Keep instruction manual for future reference.
• Keep the original packaging to store the gazebo.
• Periodically check and ensure that all bolts are well-tighten during use
MAINTENANCE
GENERAL BEST PRACTICES FOR ASSEMBLY:
The limited warranty is extended to the original purchaser and applies to material and manufacturer’s defect provided
WHAT IS COVERED?
the item is maintained with care and used only for personal, residential purposes.
Warranty: 1 Year
2/26

PARTS LIST
Label Part Number Description Qty Part Image
A P000200396 Post 4
B1 P000400801 Left Frame
(Long) 2
B2 P000400800 Right Frame
(Long) 2
C1 P000400803 Left Frame
(Short) 2
C2 P000400802 Right Frame
(Short) 2
D P000601208 Slant Beam For
Big Roof 4
E P000601210 Middle Beam For
Big Roof (Long) 2
F P000601211 Middle Beam For
Big Roof (Short) 2
G P000501034 Middle beam
connector 4
H P000601209 Slant Beam End
For Big Roof 4
K1 P000501033 Big Top
Connector 1
K2 P000501032 Small Top
Connector 1
J P000601207 Slant Beam For
Small Roof 4
L P001000036 Finial 1
M P005800001 Hook 1
N1 P005700593 Long Mosquito
Netting Pipe4
N2 P005700594 Short Mosquito
Netting Pipe4
3/26

P006100152 BaseCover 4P
P000100392 Base 4Q
P001100485 Small Canopy 1R
P001100486 Big Canopy 1S
P008100018
Plug 20*20
(Pre-Asse
mbled on H) 4V
P008100017
Plug 17*17
(Pre-Asse
mbled onE,F,J) 8W
P001200192 Mosquito Netting 1T
P001300096 Curtain 1U
4/26

Label Part Number Description Qty Add Part Image
AA H010020012 Bolt M6*20 32 4
BB H050030001 Flat washer
M6 56 8
CC Bolt M5*15 24 4
DD H050040002 Flat washer
M5 24 4
EE H040010004 Nut M6 16 4
FF H010020013 Bolt M6*35 8 2
GG P005100264 Plastic ring 104 12
HH H070010001 StakeΦ6*23
0 8 0
LL H050020017 Spring
Washer M6 24 3
WW H090020001 Wrench
M5/M6 2 0
H010020523
HARDWARE LIST
5/26

HELPFUL HINTS
• Tools needed and not included
• Separating parts before starting
Provided in hardware pack
How many people are needed for the installation
6/26

STEP 1
Assembled View:
4x
4x 4x
8x 8x
Insert the Post (A) into Base Cover (P),attached
Base (Q) to the Post (A) with Bolts (AA) and
Flat washer (BB), tighten with Wrench (WW).
7/26

STEP 2
Assembled View:
Attached Left Frame (C1) to Right Frame
(C2) with Bolts (AA),Flat washer (BB),
Spring washer(LL) and Nut (EE), tighten
with Wrench (WW).
2x
2x
4x 4x 8x 4x
8/26

STEP 3
Assembled View:
Attached Left Frame (B1) to Right Frame (B2)
with Bolts (AA),Flat washer (BB), Spring
washer(LL) and Nut (EE), tighten with Wrench
(WW).
2x
2x
4x
4x 4x
9/26
8x

STEP 4
Assembled View:
Attached Middle beam connector (G) to
assembled short frame (C1/C2) and long
frame (B1/B2) with Bolts (CC) and Flat
washer (DD), tighten with Wrench (WW).
4x
8x
8x
10/26

STEP 5
Assembled View:
Attached Short Mosquito Netting Pipe (N2)
to assembled short frame (C1/C2) with Bolts
(CC) and Flat washer (DD), tighten with
Wrench (WW).
4x
8x 8x
11/26

STEP 6
Assembled View:
Attached Long Mosquito Netting Pipe (N1)
to assembled long frame (B1/B2) with Bolts
(CC) and Flat washer (DD), tighten with
Wrench (WW).
8x
4x
12/26
8x

STEP 7
Assembled View:
Attached the assembled short frame (C1/C2) to
Post (A) with Bolts (AA), Flat washer (BB) and
Spring washer (LL), tighten with Wrench
(WW).
2x
8x
8x
13/26
8x

STEP 8
Assembled View:
Attached the assembled long frame (B1/B2)
to Post (A) with Bolts (AA), Flat washer (BB)
and Spring washer (LL), tighten with Wrench
(WW).
8x8x
2x
14/26
8x

STEP 9
Assembled View:
Insert the Slant Beam For Big Roof (D) into
Slant Beam End For Big Roof (H), click on.
4x 4x
CLICK!
15/26

STEP 10
Assembled View:
Insert the Slant Beam For Big Roof (D) into
Big Top Connector (K1), Attached Slant
Beam End For Big Roof (H) to the Post (A)
with Bolts (FF), Flat washer (BB) and Nut
(EE), tighten with Wrench (WW).
1x
4x 8x 4x
CLICK!
4x
16/26

STEP 11
Assembled View:
Insert the Middle Beam For Big Roof (E) into
Big Top Connector (K1), Attached the
Middle Beam For Big Roof (E) to Middle
beam connector (G) with Bolts (FF), Flat
washer (BB) and Nut (EE), tighten with
Wrench (WW).
2x
CLICK!
2x 4x 2x
17/26

STEP 12
Assembled View:
Insert the Middle Beam For Big Roof (F) into
Big Top Connector (K1), Attached the
Middle Beam For Big Roof (E) to Middle
beam connector (G) with Bolts (FF), Flat
washer (BB) and Nut (EE), tighten with
Wrench (WW).
2x
2x
CLICK!
2x 4x
18/26

STEP 13
Spread the Big Canopy (S) on the big roof,
don't tighten at this step.
Assembled View:
1x
19/26

STEP 14
Assembled View:
Insert the Slant Beam For Small Roof (J) to
Small Top Connector (K2), click on.
1x 4x
CLICK!
20/26