RealFlame 9000 User manual

Fireplace Model #9000
Instruction Manual
®

Rev. 06/04/07
Using your Fireplace
- Follow all instructions included with gel fuel before use.
- Before using Fireplace make sure you have read and understand the step-by-step instructions.
- During the initial burn you may experience a slight odor. This odor is temporary and will be absent on following burns.
Instructions and warnings for use
Welcome to the Real Flame® family of gel fuel products. If you have any questions
please call customer service at 1-800-654-1704 or log on to www.REALFLAME.com.
WARNINGS !!
NOTICE: Buyer assumes all responsibility for safety and use that is not
in accordance with instructions and warnings.
1. Fireplace is designed to be used with Real Flame®gel fuel only. Do not use with any other gel fuel or any other flammable
liquid or gel.
2. Read entire label and instructions before using Real Flame gel fuel.
3. Make sure fireplace is set on a flat, level and stable surface. Keep fireplace stable at all times.
4. Make sure fireplace and gel fuel are burned on a flat and level surface.
5. Never leave a burning fire unattended, especially around children or pets.
6. Fireplace is not to be operated by children. Keep away from children and pets.
7. Exercise the same precautions as you would with any open fire.
8. When in use some surfaces will be hot, use caution.
9. Never touch logs, gel fuel cans or any other metal surfaces during or immediately after burning gel fuel. They will be extremely
 HOT. Allow them to cool for 60 minutes before touching.
10. Do not burn more than three cans of fuel at once.
11. Do not place more than 15 lbs. of weight on the top of the fireplace at anytime.
12. Do not alter fireplace, metal firebox or log set in any manner.
13. Keep fireplace and gel fuel cans away from flammable materials at all times.
14. Do not store or use gasoline or any other flammable vapors, liquids, or materials in the vicinity of fireplace and gel fuel.
15. Do not wear flammable or loose clothing when operating the fireplace.
16. Do not move fireplace while in use. Do not attempt to move or store the fireplace until 60 minutes after gel fuel cans have
been extinguished.
17. Do not burn trash, paper, or wood in the fireplace. Burn only Real Flame®gel fuel in the fireplace.
18. Do not burn gel fuel outside designated burn areas on the metal grate.
19. Do not put fireplace in an area with lots of traffic, such as a hallway or entryway.
20. In case of an emergency use a CO2 extinguisher to extinguish the fire.
21. Death, serious injury or damage to property may occur if the warnings above are not followed.
22. If for any reason you cannot follow these warnings please call us at 1-800-654-1704.
®
®
STOP!
If parts are missing or damaged, call 1-800-654-1704 for assistance

Step One
figure 1
-Set Right and Left Trim Panels (4 & 5) face down
about three feet apart on a flat, carpeted surface with
grooves to outer edges.
-Set Center Panel (6) between Trim Panels so tops of all
Panels align and mounting strip at lower edge of Center
Panel rests on mounting strips of Trim Panels. Attach
Center Panel to Trim Panels with screws through pre-
drilled holes in mounting strips at outer edges of Center
Panel.
-Set Left Facing (8) face down at left side of assembly
so its mounting strip fits to inner edges of Center
Facing and Trim Panel mounting strips. Attach Left
Facing to Left Trim Panel with screws through pre-
drilled holes in mounting strip on Left Facing.
-Repeat with Right Facing (9) at right side of assembly.
-Set Center Facing (10) face down below Center Panel
so it is flush with lower edge of Center Panel. Attach
Center Facing with screws through pre-drilled holes in
Center Facing mounting strips.
Parts List
Number Description Part Number Quantity
1 Base 9001 1
2 Left Side Panel 9002 1
3 Right Side Panel 9003 1
4 Left Trim Panel 9004 1
5 Right Trim Panel 9005 1
6 Center Panel 9006 1
7 Mantel Top 9007 1
8 Left Facing 9008 1
9 Right Facing 9009 1
10 Center Facing 9010 1
11 Firebox Support 9011 1
12 Lower facing 9012 1
13 Firebox Lip 9013 1
not shown
1" Screws 9713 Bag
Firebox Clips 1075 2
9000-1 revised 042006
figure 1
Tips For Assembly
Before assembly, locate instructions and
hardware. Take out all parts and compare them
to the photograph and the assembly
illustrations. Be sure you have all parts
identified.
Check for screws that are wrapped in the
packaging to be sure you don't discard them.
You may have extra screws.
A helping hand is always good. Assemble
fireplace with an adult assistant if possible.
The cement log is heavy. Put the fireplace in
the desired location before inserting cement
log.
Use caution not to over tighten screws.
54
6
10
8
9
9000 Liberty Instructions

2 3
11
1
Step Three
figure 3
- From back, set Lower Facing (12) on Base so it
fits into space behind Right and Left Facing.
Screw Lower Facing on through pre-drilled
holes in mounting strips at its outer edges.
-From back, set Lip (13) on Lower Facing so
curved edge fits through fireplace opening and
Lip mounting strip rests on Lower Facing
mounting strip. Attach Lip with screws through
pre-drilled holes in Lip mounting strip.
-Slide Mantel Top (7) on from front of unit so
that its front and side moldings overhang the unit
and the back of the Top is flush with the back of
the unit. Screw Top to unit through pre-drilled
holes at outer edges of Top and at upper edges of
Side Panels.
9000-2 revised 042006
7
Step Two
figure 2
- Set the Base (1) on a flat, carpeted surface.
- Set the Left Side Panel (2) upright at left
side of Base so mounting blocks and
tongue edge are toward the front. Slide
Panel down into Base so notched corner
overlaps Base. Attach loosely to Base with
screws through pre-drilled holes in bottom
of Side Panel.
-Repeat using Right Side Panel (3) at right
side of Base.
- Hold Firebox Support (11) between Sides
with its wood block in back. Slide Firebox
Support pegs into slots at rear inner edges
of Sides.
- Tighten screws attaching Side Panels to Base.
- Hold entire front assembly over Base in front of
Side Panels. Align tongues at front of Side Panels
with grooves at outer edges of front assembly and
slide assembly down to Base.
- Attach Side Panels to Trim Panel assembly with
screws through pre-drilled holes in mounting blocks
on Right and Left Side Panels.
figure 3
figure 2
You are now ready for the firebox
installation. Please refer to the instructions
that are included with your firebox.