Rear view safety RVS-916619P User manual

1
TM

What’s in the Box?
•1 Color Weather Proof Backup Camera
• 7" Color TFT LCD Digital Clip-On Mirror Monitor
• 1-3 Channel Multiplexer Control Unit
• 1-33’ Extension Cable for Camera
• 1 Remote Control
• 1 Power Connection Wire
• 1 Double RCA + Power Converter
(to connect external audio, video and power)
• 1 Screw Kit for Installation

3
Table of Contents
Introduction...................................................................................................4
Safety Information.......................................................................................5
Before Beginning Installation...................................................................6
Installation uide.........................................................................................7
Wiring Camera & Monitor.....................................................................8-9
Installation Diagram .................................................................................10
Installation Monitor ..................................................................................11
Positioning.................................................................................................. 12
Multiplexer ..................................................................................................13
Monitor Dimensions..................................................................................14
Monitor Specifications.............................................................................15
Camera Dimensions...................................................................................16
Camera Specifications..............................................................................17
Splitting & Splicing ...................................................................................18
Troubleshooting..........................................................................................19
Warranty.......................................................................................................20

REAR VIEW SAFETY
4
Introduction
Congratulations on purchasing a Rear View Backup Camera Sys-
tem. With this manual you will be able to properly install and op-
erate the unit.
The Backup Camera System is intended to be installed as a
supplement aid to your standard rear view mirror that already ex-
ists in your vehicle. The Backup Camera System should not be
used as a substitute for the standard rear view mirror or for any
other mirror that exists in your vehicle.
In some jurisdictions, it is unlawful for a person to drive a
motor vehicle equipped with a TV viewer or screen located for-
ward of the back of the driver’s seat or in any location that is vis-
ible, directly or indirectly, to the driver while
operating the vehicle.
Please read all of the installation instructions
carefully before installing the product. Improper
installation will void manufacturer’s warranty.

5
Reverse With Confidence

Safety Information
Please read the entire manual and follow the instructions and
warnings carefully. Failure to do so can cause serious damage
and/or injury, including loss of life. Be sure to obey all applica-
ble local traffic and motor vehicle regulations as it pertains to
this product. Improper installation will void manufacturer’s
warranty.
USA E
•The Rear View Camera System
is designed to help the driver
safely detect people and/or
objects helping to avoid
damage or injury. However,
you the driver, must use it
properly. Use of this system is
not a substitute for safe,
proper or legal driving.
•Never back up while looking
at the monitor alone. You
should always check behind
and around the vehicle when
backing up, in the same way
as you would if the vehicle
did not have the Rear View
Camera System. If you back
up while looking only at the
monitor, you may cause
damage or injury. Always
back up slowly.
•The Rear View Camera Sys-
tem is not intended for use
during exstensive back-up
maneuvers or backing into
cross traffic or pedestrian
walkways.
•Please, always remember,
the area displayed by the
Rear View Camera System is
limited. It does not display
the entire panorama that is
behind you.

REAR VIEW SAFETY
6
INSTALLATION
•Electric shock or product
malfunction may occur if
this product is installed
incorrectly.
•Use this product within
the voltage range specified.
Failure to do so can cause
electronic shock or product
malfunction.
•Take special care when
cleaning the monitor.
•Make sure to firmly affix the
product before use.
•If smoke or a burning smell
is detected, disconnect the
system immediately.
•Where the power cable may
touch a metal case, cover the
cable with a friction tape. A
short circuit or disconnected
wire may cause a fire.
• While installing the Rear
View System be careful with
the wire positioning in order
to avoid wire damage
•The Rear View System should
only be used when the vehi-
cle is in reverse.
•Do not watch movies or
operate the monitor while
driving; as it may cause an
accident.
•Do not install the monitor
where it may obstruct drivers
view or obstruct an air bag
device.
•Dropping the unit may cause
possible mechanical failure.
Safety Information

7
Reverse With Confidence

Safety Information
IN NO EVENT SHALL SELLER OR MANUFACTURER BE
LIABLE FOR ANY DIRECT OR CONSEQUENTIAL DAMA ES OF
ANY NATURE, OR LOSSES OR EXPENSES RESULTIN FROM
ANY DEFECTIVE PRODUCT OR THE USE OF ANY PRODUCT.
If you have questions about this product, contact:
Customer Service:
Rear View Safety
1797 Atlantic Avenue
Brooklyn, NY 11233
Tel: [phone]

REAR VIEW SAFETY
8
Before You Begin Installation
Before drilling please check that no cable or wiring is on the
other side of the wall. Please clamp all wires securely to reduce
the possibility of them being damaged while vehicle is in use.
Keep all cables away from hot or moving parts and electrical
noisy components.
We recommend doing a benchmark test before installation
to insure that all components are working properly.
Step 1: Choose the monitor and camera locations.
Step 2: Install all cables in vehicle, when necessary a 0.8 (20mm)
hole should be drilled for passing camera cable through vehicles
walls. Install split grommets where applicable
Step 3: Once all cables and wiring have been properly placed
routed, perform a system function test by temporarily connecting
he system. If the problem persists see troubleshooting (page 22).
Before You Begin Installation

9
Reverse With Confidence

Installation uide
Camera
1. Attach camera bracket close to rear marker lights, centered
on vehicle.
2. Attach camera to bracket using screws provided and adjust
the angle.
Cable
1. Be sure to position the cable properly. The aviation camera
cable uses aircraft grade connectors which means the camera
cable can be exposed to all weather elements, do not run the
cable over sharp edges, do not kink the cable and keep away
from HOT and rotating parts.
2. Fasten all cable and secure all excess cable.
Monitor
1. The Mirror Monitor attaches to the existing rear view mirror in
vehicle with the pressurized clips on the back of the monitor..
2. Attach monitor to existing mirror, and adjust mounting angle
to allow optimum driver viewing comfort. (see figure 1.1 on
page 12).

REAR VIEW SAFETY
10
Wiring Camera & Monitor
•When installing a ONE (1)
camera setup, connect camera
extension cable from the rear
view camera to port # labeled
“backup” (most systems port 3)
Connect red 12V+ wire to igni-
tion power source and black
wire 12V- to chassis ground. Do
not use white and yellow wires.
•The blue wire is the REVERSE
trigger wire. In typical rear-view
installations, connecting this
wire to the vehicle’s backup
light circuit will activate the
rear-view image whenever the
vehicle shifts into reverse.
•Before drilling, be sure no cable
or wire is on the other side.
•Feed as much cable as possible
into vehicle and clamp se-
curely. This reduces the possi-
bility of cable being
hooked or snagged.
•Camera: Drill a 20mm (0.8in)
diameter hole into vehicle
body near the camera and
bracket. Insert camera cable
into vehicle (be careful not to
kink cable) and fit grommet
into hole. Apply sealant
around grommet to increase
resistance to water penetra-
tion. Connect camera to the
camera extension cable which
runs inside the vehicle.
•The camera system can be wired
to be powered “ON” the entire
time the vehicle is activated and
this is typical in RV and some
Commercial applications.
•The camera and monitor can
always be activated by manu-
ally pushing the power button
on monitor this is in addition to
utilizing the positive triggers.
Note: If connecting power
directly to battery, the camera
is always ON and therefor can
drain battery, therefore its
recommended to connect
power to an ignition switched
accessory power source.