Redexim Speedseed 1100 User manual

User Manual and
Parts book
SPEEDSEED
1100-1500-2000-2300
2005 English 924.120.202
REDEXIM
Kwekerijweg 8
3709JA –Zeist –The Netherlands
Tel.: [phone]
Email: [email protected]
www.redexim.com

Redexim
2
EU DECLARATION
We –Redexim BV, Utrechtseweg 127, 3702 AC Zeist, Holland –declare entirely under our own
responsibility that the product:
SPEEDSEED WITH A MACHINE NUMBER AS INDICATED ON THE MACHINE AND INDICATED
IN THIS MANUAL
to which this declaration refers, complies with stipulation of the 2006/42/EC machine directive and with
the norms NEN-EN-ISO 12100:2010, NEN-EN-ISO 13857:2008.
Zeist, 09.11.18
A.C. Bos
Manager Operations & Logistics
Redexim Holland

Redexim
3
FOREWORD
Congratulations on your Speedseed purchase. For safe and long-lasting operation of this machine, it is
necessary to read and to understand this user manual. It is impossible to work safely with this machine without
complete knowledge of the content of the user manual.
This machine does not operate independently! It is the user’s responsibility to use the correct tractor or other
towing vehicle. The user should check the combination of the towing vehicle and the machine with regard to
various aspects, such as noise level and safety risks. In addition, the user should comply with the user
instructions of the vehicle and spare parts that are used.
All information and technical specifications provided at the moment that this document is published are
the most recent ones. Design specifications may be changed without prior notice.
You can contact your sales point or dealer if you have questions and/or if there are ambiguities in this
manual or about the machine concerned.
WARRANTY CONDITIONS
AT THE TIME OF DELIVERY THIS MACHINE IS GUARANTEED AGAINST MATERIAL DEFECTS.
THIS WARRANTY IS VALID FOR A PERIOD OF 12 MONTHS FROM THE PURCHASE DATE.
REDEXIM WARRANTIES ARE SUBJECT TO THE ‘GENERAL CONDITIONS FOR SUPPLY OF PLANT AND
MACHINERY FOR EXPORT, NUMBER 188’ THAT ARE PUBLISHED UNDER THE AUSPICES OF THE
UNITED NATIONS ECONOMIC COMMISSION FOR EUROPE.
REGISTRATION CARD
For your own information, fill in the table below:
Serial number of the machine
Dealer name
Date of purchase
Remarks

Redexim
4
TABLE OF CONTENTS
1. SAFETY INSTRUCTIONS.......................................................................................................... 5
1.1. Obligations of the user................................................................................................... 5
1.2. Maintenance, repairs and adjustments.......................................................................... 6
1.3. Using the machine......................................................................................................... 6
2. TECHNICAL DATA.................................................................................................................... 7
3. GENERAL DESCRIPTION......................................................................................................... 8
4. SAFETY STICKERS .................................................................................................................. 8
5. FIRST INSTALLATION.............................................................................................................. 9
6. ATTACHING AND DETACHING THE MACHINE ................................................................... 10
6.1. Attaching the machine ................................................................................................. 10
6.2. Detaching the machine................................................................................................ 11
7. MACHINE SETTINGS.............................................................................................................. 11
7.1. Setting the seed-element valves.................................................................................. 11
7.2. Setting the quantity of seeds using the gearbox.......................................................... 12
7.3. Turning test.................................................................................................................. 13
8. TRANSPORT ........................................................................................................................... 14
9. START/STOP PROCEDURE................................................................................................... 15
9.1. Safety........................................................................................................................... 15
9.2. Starting to sow ............................................................................................................. 15
9.3. Stop sowing ................................................................................................................. 16
10. MAINTENANCE ....................................................................................................................... 17
10.1. Lubrication points......................................................................................................... 17
11. TROUBLE SHOOTING (PROBLEM ANALYSIS) ................................................................... 18
12. OPTIONAL: SET OF WEIGHTS.............................................................................................. 19
13. OPTIONAL: SPIKES ON THE REAR ROLLER...................................................................... 20
14. OPTIONAL: BRUSH SCRAPER ............................................................................................. 21
15. OPTIONAL: CRUMB ROLLER................................................................................................ 22
16. OPTIONAL: DIGITAL SURFACE METER .............................................................................. 23
17. OPTIONAL: SET OF WHEELS ............................................................................................... 24

Redexim
5
1. SAFETY INSTRUCTIONS
This machine is designed for safe use. This can only be achieved if you completely follow the safety
instructions described in this manual.
Read and understand the manual before you start using this machine.
If the machine is not used as described in this manual, this can result in injuries and/or damage to the
machine.
This user manual lists instructions that are numbered in sequence. You should follow this sequence. A
is an indication of a safety instruction. A means a tip and/or note.
1.1. Obligations of the user
Treating fields/lawns is the only purpose of the machine. Any other use is improper. The manufacturer
will not accept any liability for damage resulting from improper use. All risks occurring with this are
entirely at the expense of the user.
All persons assigned to operate, maintain and repair the machine by the owner must completely read
and understand the operation manual and in particular the chapter of Safety Instructions.
Modifications to the machine that have a negative impact on the safety must be rectified immediately.
The user is obliged to check the machine for visible damage and defects before using the machine.
For safety reasons it is not permitted to make changes or adjustments to the machine (except those
approved by the manufacturer). If modifications to the machine have been made, then the current CE
marking is cancelled. The person that has made these modifications has to apply for a new CE
marking himself.
Following the use, maintenance and repair instructions prescribed by the manufacturer is also
considered proper use of this machine.
The user is responsible for the safe combination of the machine and the towing vehicle, which comply
with the requirements as described in the Technical Data (see Chapter 2). This entire combination
should be tested for noise, safety, risk and user friendliness. User instructions should also be drafted.
Dress appropriately during work activities with the machine. Wear sturdy shoes with steel
toecaps, long trousers and tie up long hair. Do not wear loose clothing.
The general applicable health & safety (Dutch: ARBO) regulations must also be followed in addition to
the instructions in this user manual.
Relevant traffic regulations also apply in case of using public roads.

Redexim
6
1.2. Maintenance, repairs and adjustments
Keep a record of the repair activities.
When unskilled people use, maintain or repair the machine, this could result in injuries to the user and
to third parties. This should be avoided!
Use only original Redexim parts for maintenance or repairs because of the safety of the machine and
of the user.
Only authorised technical personnel may carry out repairs to the machine.
When carrying out maintenance, adjustments and repairs, it is necessary to block the machine in
order to prevent it from sinking away, driving off and/or sliding off.
If a hydraulic installation is present, you should always make it pressure-free before working on this
installation.
Used oil/grease is harmful to the environment. Dispose of these substances according to the
regulations that apply in your location.
1.3. Using the machine
Attach the machine to the towing vehicle according to the regulations. Pay close attention to the risk of
injury!
Never use the machine in the absence of protective guards and safety stickers.
Check the machine for loose bolts, nuts and components before every operation.
Check whether you have a clear field of vision –both close by and far away –before you start moving.
All persons that are going to operate the machine must be familiar with all the functions and control
elements of the machine before starting any work activities.
Never crawl under the machine! If necessary, tip over the machine to work at the bottom side.
If present, check the hydraulic hoses regularly and replace these when the hydraulic hoses are
damaged or appear old.

Redexim
7
2. TECHNICAL DATA
Type
Speedseed 1100
Speedseed 1500
Recommended vehicle
20 pk with a minimum lifting
capacity of 450 kg (990 lbs)
measured 610 mm behind the
lifting eyes
30 pk with a minimum lifting
capacity of 550 kg (1212 lbs)
measured 610 mm behind the
lifting eyes
Working width
1.1 m. (43.3”)
1.5 m. (59”)
Working depth
5 –20 mm (0.19” – 0.78”)
5 –20 mm (0.19” – 0.78”)
Sowing speed
Max. 12 km/h (7.5 mph)
Max. 12 km/h (7.5 mph)
Sow hole distance
Square 30 mm (1.18”)
Square 30 mm (1.18”)
Number of holes per m2
using a single spiked roller
990
990
Weight
380 kg (836 lbs)
468 kg (1030 lbs)
Dimensions (L x W x H)
0.88 x 1.52 x 1.02 m.
(34.8” x 60.1” x 40.1”)
0.88 x 1.91 x 1.02 m.
(34.8” x 75.5” x 40.1”)
Three-point system
Cat. 1-2
Cat. 1-2
Bearing grease to be used
EP 2
EP 2
Content of the sand bin
169 l.(5.9 cu.ft.)
224 l.(7.84 cu. Ft.)
Tyre pressure
1 –2 bar (14.5 –29 Psi)
1 –2 bar (14.5 –29 Psi)
Optional
-Rear roller with spikes
-Brush scraper
-Digital counter
-Crush roller
-Set of weights
-Set of wheels
-Rear roller with spikes
-Brush scraper
-Digital counter
-Crush roller
-Set of weights
-Set of wheels
Type
Speedseed 2000
Speedseed 2300
Recommended vehicle
40 pk with a minimum lifting
capacity of 595 kg (1310 lbs)
measured 610 mm behind the
lifting eyes
40 pk with a minimum lifting
capacity of 650 kg (1430 lbs)
measured 610 mm behind the
lifting eyes
Working width
2.0 m. (78.7”)
2.3 m. (90.6”)
Working depth
5 –20 mm (0.19” – 0.78”)
5 –20 mm (0.19” – 0.78”)
Sowing speed
Max. 12 km/h (7.5 mph)
Max. 12 km/h (7.5 mph)
Sow hole distance
Square 30 mm (1.18”)
Square 30 mm (1.18”)
Number of holes per m2
using a single spiked roller
990
990
Weight
591 kg (1300 lbs)
650 kg (1430 lbs)
Dimensions (L x W x H)
0.88 x 2.44 x 1.02 m.
(34.8” x 96.1” x 40.1”)
0.88 x 2.72 x 1.02 m.
(34.8” x 107.4” x 40.1”)
Three-point system
Cat. 1-2
Cat. 1-2
Bearing grease to be used
EP 2
EP 2
Content of the sand bin
297 l.(10.4 cu.ft.)
337 l.(11.8 cu. Ft.)
Tyre pressure
1 –2 bar (14.5 –29 Psi)
1 –2 bar (14.5 –29 Psi)
Optional
-Rear roller with spikes
-Brush scraper
-Digital counter
-Crush roller
-Set of weights
-Set of wheels
-Rear roller with spikes
-Brush scraper
-Digital counter
-Crush roller
-Set of weights
-Set of wheels

Redexim
8
3. GENERAL DESCRIPTION
The Speedseed is a machine for sowing grass areas.
4. SAFETY STICKERS
Safety stickers are located on both sides of the machine. These safety stickers must always be clearly
visible and legible and must be replaced if they have become damaged.
933.280.402
-In case of maintenance, adjustments and repair, always
switch OFF the engine of the towing vehicle.
-Keep a distance of minimum 4 metres if the machine is
operating (except the operator).
900.280.402
-Prior to using the machine, the operators of the machine
must read the user manual carefully.

Redexim
9
5. FIRST INSTALLATION
The machine should be prepared for use as follows (Figure 1):
1. Attach cables to the hoisting points (1).
Ensure that the crane and hoisting cable can handle at least the following weights:
Speedseed 1100 500 kg (1100 lbs)
Speedseed 1500 650 kg (1430 lbs
Speedseed 2000 700 kg (1540 lbs)
Speedseed 2300 850 kg (1870 lbs)
2. Lift the machine including the pallet approx. 10 cm (4”) off the ground.
3. Loosen the pallet by removing the 3-point pins at the bottom (2).
4. Pull the pallet from under the machine.
5. Carefully lower the machine until it stands safely on the ground.
!! KEEP A SAFE DISTANCE. THE MACHINE MAY START TO SLIDE DURING HOISTING !!
!! NEVER CRAWL UNDER THE MACHINE !!
Figure 1

Redexim
10
6. ATTACHING AND DETACHING THE MACHINE
Attaching and detaching the machine has to be done carefully. Follow the instructions below:
Figure 2
6.1. Attaching the machine
Prior to attaching the machine, check the following points:
-Check whether the machine is undamaged and whether it is safe to attach and use
the machine.
-Check whether the bolts and nuts are tightened with the correct torque.
-Check whether all safety stickers are on the machine and whether these are
undamaged and easily readable. Never use the machine if it has damaged or
unreadable stickers.
The machine should be attached to the tractor in the following manner:
1. Remove the 3-point pins (1) at the top from the machine (see Figure 2).
2. Carefully drive the tractor backwards until the lifting arms (2) can be attached to the
machine.
!! Make sure that the tractor and the machine cannot move while you are attaching
them !!
!! Switch off the tractor engine before attaching the machine !!
3. Attach the lifting arms (2) to the machine using the 3-point pins (3). Lock the pins
using the R-clips.
4. Set the stabilizer to a sideways stroke of 100 mm.
5. Mount the top rod (4) onto the tractor and attach it to the machine.
6. Adjust the top rod in such a manner that the machine is horizontal.
!! Make sure that the 3-point pins are locked using the R-clips !!
7. Start the tractor and lift the machine off the ground.

Redexim
11
6.2. Detaching the machine
The machine should be detached in the following manner (see Figure 2):
1. Place the tractor and the machine on a flat surface.
!! Make sure that the machine and the tractor cannot move while you are detaching
them !!
!! Switch off the tractor engine before detaching the machine !!
2. Carefully place the machine on the ground.
3. Loosen the top rod (4) and remove it.
4. Loosen the lowest arms (2).
!! The ground must be flat !!
!! First, you will have to remove additional weight !!
5. Start the tractor and drive off.
7. MACHINE SETTINGS
The Speedseed has several options for setting the machine optimally.
7.1. Setting the seed-element valves
The machine is suitable for sowing different types of seeds. Furthermore, the Speedseed can also be
used in combination with various tractors and you can sow at different speeds. To adjust the machine
to the various factors, the machine’s sowing installation must be adjusted. The sowing elements have
a number of functions (see Figure 3b):
1. If the valve is closed, no seeds can flow out of the hopper when the machine is idle
(e.g., during transport).
2. To empty the hopper after sowing, the sowing-element valve can be opened so that
the seeds can run out of the hopper.
3. The valve can be adjusted according to the size of the seeds that will be sown. In
case of fine grass seed, the element valve must be closed completely. Then the gear
wheel grabs the seeds. In the case of larger seeds, the space between the gear wheel
and the valve is not large enough to let the seeds pass. Therefore, the valve needs to
be opened more for larger seeds. Adjusting the size of the opening can be done using
the valve adjustment handle. The handle can be adjusted by loosening the stellar
knob (1), selecting the required position by means of the indication sticker (2), and
retightening the stellar knob (see Figure 3a).

Redexim
12
Figuur 3a Figuur 3b
7.2. Setting the quantity of seeds using the gearbox
By affecting the setting of the sowing elements, the delivery of seeds can be set to additional or fewer
seeds. Each sowing element contains a rotor that transports the seeds. By affecting the speed of the
gears, the quantity of seeds can be adjusted. The gearbox can adjust the speed continuously-variable.
Do the following to adjust the quantity of the seeds:
1. Loosen the stellar knobs (1) (see Figure 4).
2. Rotate the stellar knob (2) to change the settings. You can see the settings on the
sticker (3).
3. Retighten the stellar knobs (1).
Figure 4
If the gearbox is in the maximum position and there are still not enough seeds coming out of the
machine, the seed-element valves need to be readjusted.

Redexim
13
7.3. Turning test
The quantity of seeds should be adjusted for the correct operation of the Speedseed. See Table 1 for
an indication of the required quantity.
You should consider the following instructions for this:
!! Make sure that the Speedseed and the tractor cannot move while you are setting
them !!
!! Switch off the tractor engine before descending from the tractor !!
You will need the following accessories for adjusting the quantity of seeds:
1. A scale
2. A tray for weighing the seeds
3. Enough seeds for filling the hopper for minimum 30%
The procedure is as follows (see Figure 5):
1. Fill the hopper with seeds and make sure that these are evenly spread throughout the
hopper.
2. Lift the Speedseed off the ground so that the wheel can rotate freely.
3. Place a blanket or a piece of carton (1) under the machine.
4. Turn the wheel (2) 13 rotations counter-clockwise.
5. Weigh the seeds in kilograms and multiply the outcome by:
Speedseed 1100: 551
Speedseed 1500: 404
Speedseed 2000: 303
Speedseed 2300: 264
The resulting outcome is the amount of seeds in kilograms that should be spread per hectare.
To obtain the outcome in pounds per acre, multiply the resulting outcome by 0.89.
!! Attention! If the bin is in a high position, it can may cause the release of a large
quantity of seeds. Then divide the 13 rotations in several smaller steps !!
Figure 5

Redexim
14
Sowing table
Gearbox setting
Gate opening
Ryegrass
Kg/ha
Pound/Acre
0
0
0
0
1
0
12,7
11,4
2
0
39,8
35,5
3
0
67,6
60,3
4
0
100,2
89,4
5
0
131,1
117,0
6
0
167,7
149,6
7
0
209,1
186,6
8
0
257,5
229,7
9
0
315,6
281,6
10
0
376,6
336,0
11
0
476,7
425,3
Table 1
Sowing table
Gearbox setting
Gate opening
Bluegrass
Kg/ha
Pound/Acre
0
0
0
0
1
0
18,7
16,7
2
0
79,5
70,9
3
0
121,0
108,0
4
0
172,4
153,8
5
0
235,5
210,1
6
0
301,2
268,7
7
0
376,9
336,3
8
0
482,6
430,6
9
0
578,7
516,3
10
0
680,8
607,4
11
0
873,9
779,7
Table 2
Sowing table
Gearbox setting
Gate opening
Red Fescue grass
Kg/ha
Pound/Acre
0
0
0
0
1
0
11,3
10,1
2
0
36,2
32,3
3
0
62,7
56,0
4
0
87,3
77,9
5
0
120,9
107,8
6
0
153,2
136,7
7
0
190,1
169,6
8
0
236,7
211,2
9
0
287,3
256,3
10
0
353,3
315,2
11
0
437,3
390,1
Table 3

Redexim
15
8. TRANSPORT
The user is responsible for transporting the Speedseed in back of the tractor on public roads. Verify
the national legislation regarding the regulations. On open fields while the machine is raised, the
maximum permitted speed is 20 km/h (12.4 mph) due to the weight of the Speedseed. A higher speed
can be dangerous for the driver and/or the public and can even damage the machine.
!! When the machine is raised off the ground, the front axle of the tractor has to support
minimum 20% of the tractor’s weight !!
9. START/STOP PROCEDURE
9.1. Safety
Before using the Speedseed, you should check the following:
1. Are there loose objects in the field? First remove these objects.
2. Are there slopes? The maximum slope is 20 degrees for this machine. Always go from top
to bottom.
3. Are there hard objects in the ground? If so, use the Speedseed at adjusted speed.
4. Is there danger of flying objects (e.g., golf balls) that distract the attention of the driver? If
so, the Speedseed CANNOT be used.
5. Is there danger of sinking/sliding away? If so, postpone sowing.
6. If the soil is frozen or very wet, postpone the activities until conditions improve.
7. Check whether the hopper is not too damp. Dampness can cause the seeds to stick to each
other and this leads to a poor result.
8. Do NOT make sharp curves when the Speedseed touches the ground.
A few general remarks/tips about using the Speedseed:
!! If a hard object in the ground is hit, the spikes can get damaged !!
!! NEVER drive backwards when the drive wheel is on the ground !!
9.2. Starting to sow
Prior to sowing using the machine, check the following the points:
!! Make sure that the Speedseed and the tractor cannot move while you are setting
them !!
!! Switch off the tractor engine before descending from the tractor !!
•Check the sowing elements for damage and repair these if necessary.
•Check whether the seed outlet is not blocked.
•Check whether the machine is not damp, particularly the sowing system.
•Check whether the seeds are distributed equally; rotate the wheel once
counter-clockwise.
•Check whether the drive runs smoothly.

Redexim
16
The start procedure is VERY important. Follow the described procedure, because otherwise the
Speedseed can get damaged.
1. Fill seeds into the hopper.
2. Adjust the gearbox to the type of seeds that should be sown.
!! Make sure that the Speedseed and the tractor cannot move while you are setting
them !!
3. Drive to a spot where the machine will be used.
4. Drive slowly forward and lower the Speedseed slowly until the machine drives
completely on the ground.
5. Increase the speed to the required speed.
!! The maximum working speed is 12 km/h. Higher speeds are not recommended and
can cause damage to the Speedseed !!
9.3. Stop sowing
1. Reduce the speed.
2. Lift the machine off the ground.
3. Drive to the next spot for sowing and start to sow.

Redexim
17
10. MAINTENANCE
Time schedule
Check / Grease point
Method
Before every use
Check for loose bolts / nuts.
Tighten loose bolts / nuts with the
correct tightening moment.
Presence and readability of the
safety stickers
Replace these if not present or
damaged.
After every use
Clean the machine.
Only use air to clean the machine. Do
NOT use water.
After the first 20 working
hours (new or repaired)
Check for loose bolts / nuts.
Tighten loose bolts / nuts with the
correct tightening moment.
Provide the lubrication points with
grease.
Use EP2 grease
1 shot
Check whether the drive chains are
greased adequately.
Grease the drive chains.
After every 100 hours
Check whether there is sufficient
grease in the gearbox.
Fill the gearbox with 2.8 litres of EP0
grease.
Check whether the drive chains are
greased adequately.
Grease the drive chains.
Check whether the hopper is clean.
Clean the hopper.
Provide the lubrication points with
grease.
Use EP2 grease
Table 7
10.1. Lubrication points
To guarantee the proper functioning of the Speedseed, the lubrication points at both sides of the
machine (see Figure 6) must be greased periodically. Grease these points according to Table 7.
Figure 6

Redexim
18
11. TROUBLE SHOOTING (PROBLEM ANALYSIS)
Problem
Possible cause
Solution
The seeds do not reach
the correct depth.
The soil is too hard.
Aerate / irrigate
Too little pressure on the front
roller
Adjust the machine so that only the front
roller touches the ground.
Not enough weight on the machine
Stack more weight on the machine.
Spikes are worn out
Replace the spikes
The tractor does not
have sufficient traction.
Soil is too wet
Postpone sowing
Not enough weight on the machine
Stack more weight on the machine
No seeds come out of
the machine.
The seeds stick to each other
because they are too wet
Use dry seeds
Gearbox is in the wrong position
Adjust the gearbox
The handle for operating the seed-
element valves is closed
Operate the handle to open the flap
No seeds in the hopper
Check whether there are enough seeds
in the hopper. Top up if necessary.
Too many seeds come
out of the machine.
The handle for operating the seed-
element valves is opened too far
Readjust the handle for operating the
seed-element valves

Redexim
19
12. OPTIONAL: SET OF WEIGHTS
Standard, the Speedseed is equipped with a front bar to which the weights (1) can be attached (see
Figure 7).
Please refer to the parts manual for the correct quantity of weights.
Figure 7
Do the following to mount the weights:
1. Remove the locking pin (2).
2. Slide the required number of weights (1) onto the axle.
3. Return the locking pin (2) into the frame.
The following weights per machine are available:
•Speedseed 1100: 6x 492.502.800 (120 kg)
•Speedseed 1500: 12x 492.502.800 (240 kg)
•Speedseed 2000: 20x 492.502.800 (400 kg)
•Speedseed 2300: 26x 492.502.800 (520 kg)

Redexim
20
13. OPTIONAL: SPIKES ON THE REAR ROLLER
You have the possibility to mount spikes on the rear roller (see Figure 8).
The article numbers for these spikes are:
•Speedseed 1100: 224.120.000
•Speedseed 1500: 224.160.002
•Speedseed 2000: 224.210.000
•Speedseed 2300: 224.240.000
Please refer to the parts manual for the correct assembly.
!! When mounting the spikes, make sure that you use approved hoisting equipment,
never crawl under the machine and take into account that the spikes have sharp
points !!
1. Ensure that the machine stands firmly on the ground and cannot move.
2. Lift the rear side of the machine off the ground so that the rear roller can roll freely.
3. Dismount the protective plate at the rear side (1).
4. Dismount the rear roller.
5. Dismount the scraper. Save the scraper for cases in which you want to work with a
smooth rear roller.
6. Dismount the brush (2).
7. Mount the spike elements.
8. Mount the roller with the spikes (3) in the most forward position (4).
9. Mount the brush (2) in the rear position (5).
10. Mount the protective plate at the rear side (1).
11. Slowly lower the machine onto the ground.
Figure 8