Reliable JL-14 User manual

Reliable Automatic Sprinkler Co., Inc., 103 Fairview Park Drive, Elmsford, New York 10523
Bulletin 018 Rev. H
Bulletin 018 Rev. H
Model JL-14 (SIN RA1812)
K14.0 (200 metric)
Early Suppression
Fast Response Sprinkler
Product Description
The Reliable Model JL-14 Early Suppression Fast
Response (ESFR) Sprinkler is intended for use against
severe fire challenges. This sprinkler is designed to re-
spond quickly to growing fires and will deliver a heavy
water discharge to “suppress” rather than “control”
fires.
Note: The Model JL-14 ESFR sprinkler utilizes a le-
vered fusible alloy solder link in either a 165°F (74°C)
or a 212°F (100°C) rating. FM Global considers this
a “Quick Response” storage sprinkler for use in Data
Sheet 8-9.
The sprinkler has a Nominal K Factor of 14.0 (metric
200) and will deliver approximately 100 gpm (378 L/min)
of water at 50 psi (3,5 bar).
The deflector and frame provide a broad, very sym-
metrical, hemispherical pattern capable of suppressing
fires between sprinklers in high storage height areas
and at the same time retaining a high momentum cen-
tral core to penetrate and suppress fires occurring di-
rectly beneath the sprinkler in low storage height areas.
Application and Installation
The Model JL-14 ESFR sprinkler is intended for instal-
lation in accordance with NFPA 13 and FM Loss Pre-
vention Data Sheets 2-0 and 8-9 as well as the Authority
Having Jurisdiction.
This sprinkler is intended for protection of palletized
and solid piled and open frame single row, double row,
multiple row and portable rack storage of most com-
mon materials including unexpanded and cartoned ex-
panded plastics.
The JL-14 ESFR sprinkler was designed to be short-
er, and more compact than other ESFR sprinklers. The
shorter sprinkler allows piping to be installed further
from the ceiling and obstructions. The JL-14 ESFR
sprinkler is also less susceptible to damage due to
smaller deflector and frame design. The lighter JL-14
ESFR passed rough use and abuse test in the labs with-
out plastic protectors.
The Model JL-14 ESFR Sprinkler is FM approved
when installed in accordance with Factory Mutual Loss
Prevention Data Sheet 8-9 and Data Sheet 2-0 and oth-
er FM Installation Standards.
The Model JL-14 ESFR Sprinkler is UL Listed and
Certified for Canada for installation in accordance with
NFPA 13 Standards.
Model JL-14 ESFR Sprinkler
Design Criteria
General guidelines:
Orientation: Pendent. Deflector should be parallel
with the ceiling or roof.
System Type: Wet Pipe Systems Only
Maximum area of coverage: 100 ft2(9,3m2), greater
coverage area are allowable in some cases.
Minimum area of coverage: 64 ft2(5,8m2)
Maximum slope ceiling: 2/12 pitch (9.5°)
Maximum spacing: 12 ft (3,7m) for building heights up
to 30 ft (9,1m) and 10 feet (3,1m) for building heights
greater than 30 ft (9,1m)
Minimum spacing: 8 feet (2,4m)
Deflector distance from walls: At least 4 inches
(102mm) from walls, and no more than one-half the al-
lowable distance permitted between sprinklers.
Deflector to Top of Storage: at least 36in (914mm).
Deflector to ceiling Distance: 6-14 in (152-356mm)
per NFPA 13. 5-14 in (121-35mm) per FM 2-2.
Center Line of Thermal Sensing
Element To Ceiling Distance: 4-13 in (102-330mm)
per FM
Listings and Approvals
1. Listed by Underwriters Laboratories Inc. and UL cer-
tified for Canada (cULus)
2. FM Approved as a storage sprinkler
3. VdS Schadenverhütung GmbH (VdS)
4. Loss Prevention Certification Board (LPCB)
5. CNBOP-PIB Technical Approval

Reliable Automatic Sprinkler Co., Inc.
[phone] Sales Offices
[phone] Sales Fax
[phone] Corporate Offices
www.reliablesprinkler.com Internet Address
Manufactured by
Recycled
Paper
Revision lines indicate updated or new data.
EG. Printed in U.S.A. 11/17 P/N 9999970378
The equipment presented in this bulletin is to be installed in accordance with the latest published Standards of the National Fire Protection Association, Factory
Mutual Research Corporation, or other similar organizations and also with the provisions of governmental codes or ordinances whenever applicable.
Products manufactured and distributed by Reliable have been protecting life and property for almost 100 years.
Model JL-14 Temperature Ratings
Classification
Sprinkler
Temperature Link
Color
Frame
Color
Maximum Ceiling
Temperature
Sprinkler Identification
Number
(SIN)
°F °C °F °C
Ordinary
Intermediate
165
212
74
100
Black
White
Uncolored
White
100
150
38
66 RA1812
Installation Data
Sprinkler
Type
Thread
Size
Nominal
“K” Factor
Maximum
Working
Pressure
Finish
US Metric
Pendent
Only ¾” (R¾) 14.0 200 175 psi (12,1 bar) Bronze
Use only the Model J1
sprinkler wrench for re-
moval and installation. Any
other type of wrench may
damage the sprinkler.
Model J1 Sprinkler Wrench
Maintenance
The Model JL-14 ESFR Sprinkler should be inspected
and the sprinkler system maintained in accordance
with NFPA 25. Do not clean sprinkler with soap and wa-
ter, ammonia or any other cleaning fluid. Replace any
sprinkler that has been painted (other than factory ap-
plied) or damaged in any way. A stock of spare sprin-
klers should be maintained to allow quick replacement
of damaged or operated sprinklers. Prior to installation,
sprinklers should be maintained in the original cartons
and packaging until used, to minimize the potential for
damage to sprinklers that would cause improper opera-
tion or non-operation.
Once operated, automatic sprinklers cannot be reas-
sembled and reused. New sprinklers of the same size,
type and temperature rating must be installed. A cabi-
net of replacement sprinklers should be provided for
this purpose.
Model JL-14 ESFR Sprinkler Specification
Sprinklers shall be Early Suppression Fast Response
(ESFR) pendent suppression mode sprinklers specifically
tested and [UL Listed] [FM Approved] for commodity stor-
age applications. Sprinkler frame and deflector to be of
bronze construction. Fusible link assembly shall utilize the
strut and lever principle of operation with approved fast
response black-painted or white-painted beryllium-nickel
thermal element. Water seal shall consist of a Electroless
Nickel PTFE coated Bellville spring washer and brass cap
assembly containing no plastic parts. ESFR sprinklers
shall have a nominal K-factor of 14.0 with ¾” NPT thread-
ed end connections. Sprinkler temperature rating shall
be [Ordinary 165°F (74°C)] [Intermediate 212°F (100°C)].
ESFR pendent sprinklers shall be Reliable Model JL-14
(Bulletin 018).
Note: Sprinklers should be tightened between 14 - 20
ft-lbs (19 - 27,1 N-m) torque. Sprinklers not tightened to
recommended torque may cause leakage or impairment
of the sprinklers. Damage sprinklers must be replaced
immediately.
Ordering Information
Specify:
1. Temperature rating
2. Thread type 3/4” NPT or ISO 7-R3/4
Note: Grooved sprinkler boss provided to ensure that the
sprinkler wrench does not slip during installation.