ResMed AIRCurve 10 Vauto User manual

Water tub for humidification
Air outlet for connecting the air tubing
Dial for navigating and changing options
Home button for returning to the
Home screen at any time
Start/Stop button for starting therapy
Quick start guide
English

Read your entire AirCurve™ 10 User Guide before use.
Setup
12
Place the device on a stable level surface. Plug the power connector into the rear of
the device. Connect one end of the power
cord into the power supply unit and the
other end into the power outlet.
3 4
Connect the air tubing firmly to the air outlet
located on the rear of the device.
Open the water tub and fill with water up to
the maximum water level mark.
5 6
Close the water tub and insert it into the
side of the device.
Connect the free end of the air tubing firmly
onto the assembled mask. Press Start/Stop
to begin therapy.

Adjusting to therapy
If you are a first time user, you might need some time to get used to therapy. This is not unusual as
it takes most patients between one and two weeks to adjust to the air pressure.
Overcoming symptoms by changing comfort settings
If your are having difficulties getting used to therapy, use the AirCurve 10 comfort features to help
you on your journey to better sleep.
•Dry or runny nose—If you are getting a dry or runny nose, adjust the Humidity Level by turning it
up.
•Droplets of water (condensation)—If you are getting droplets of water on your nose, mask or air
tubing, adjust the Humidity Level by turning it down.
To change the Humidity Level:
3. Turn the dial to
adjust to your
preferred setting.
1. Press the dial to
enter My Options.
2. Turn the dial
to highlight
Humidity Level
and then press to
select it.
4. Press the dial to
save the change.
•Trouble falling asleep—If you are having trouble falling asleep with high pressure, turn on Ramp
or increase Ramp Time.
•Bloated feeling—If you are experiencing a slightly bloated feeling from swallowing air, turn on
Ramp or increase Ramp Time.
•Feeling of not getting enough air—If you feel like you are not getting enough air, turn Ramp
Time to Off.
To change the Ramp Time:
3. Turn the dial to
adjust to your
preferred setting.
1. Press the dial to
enter My Options.
2. Turn the dial to
highlight Ramp
Time and then
press to select it.
4. Press the dial to
save the change.

ResMed.com
378662
Cleaning
1. Wash the water tub and air tubing in warm water using mild detergent.
Do not wash in a dishwasher or washing machine.
2. Rinse the water tub and air tubing thoroughly and allow to dry out of direct sunlight and/or heat.
3. Wipe the exterior of the device with a dry cloth.
Refer to your mask User Guide for detailed instructions on cleaning your mask.
Checking and replacing your parts regularly
It is important for your comfort and health that you check and replace your parts and supplies
regularly. Replacing your parts and supplies on a regular basis helps ensure you are receiving optimal
therapy and continued comfort.
Refer to your AirCurve 10 User Guide for detailed instructions on checking your device. Contact your
care provider for information on your replacement schedule.
Replacement schedule guide:
Every Month Every 3 Months Every 6 Months
Mask cushion or pillow Mask frame
(excludes headgear)
Headgear
Air filters Air tubing Water tub
Register today
myAir™ allows you to access your therapy data and provides personalized support.
Every journey starts with a first step. Register today at ResMed.com/myAir
Serial number Device number
Mask type and size Date of setup
Notes
ResMed Ltd
1 Elizabeth Macarthur Drive
Bella Vista NSW 2153 Australia
DISTRIBUTED BY
ResMed Corp 9001 Spectrum Center Boulevard San Diego CA 92123 USA
ResMed (UK) Ltd 96 Jubilee Ave Milton Park Abingdon Oxfordshire OX14 4RW UK
See www.resmed.com for other ResMed locations worldwide. For patent information, see www.resmed.com/ip.
AirCurve is a trademark of ResMed Ltd. © 2014 ResMed Ltd. 378662/1 2014-09