ResMed AirFit P10 User manual

User guide
User guide
English | 简体中文 | 繁體中文
Bahasa Melayu | Indonesia

ii
1
3
2
(a) (b) (c)
Fitting / 配戴步骤配戴步骤 /配戴步驟 /Pemasangan /
Pengepasan
Adjustment / 调整调整 /調整 / Penyesuaian / Penyesuaian

iii
1
2 3
Removal / 取下面罩取下面罩 /取下面罩 /Penanggalan /
Pelepasan
Disassembly / 拆卸拆卸 /拆卸 /Menyahpasang /
Pembongkaran Rakitan

iv
1
2
3
618264 Book.indb 6 21/08/2013 11:38:40 AM
Reassembly / 重新组装重新组装 /重新組裝 /
Pemasangan semula / Perakitan Ulang

English 1
ENGLISH
AirFit™ P10
Nasal Pillows System
Thank you for choosing the AirFit P10. This document provides the user
instructions for the AirFit P10 and AirFit P10 for Her masks referred to
collectively as AirFit P10 throughout this manual. AirFit P10 has blue
headgear while AirFit P10 for Her has pink headgear.
Using this guide
Please read the entire guide before use. When following instructions,
refer to the images at the front and back of the guide.
Intended use
The AirFit P10 channels airflow noninvasively to a patient from a positive
airway pressure (PAP) device such as a continuous positive airway
pressure (CPAP) or bilevel device.
The AirFit P10 is:
•to be used by patients (>30 kg) for whom positive airway pressure has
been prescribed
•intended for single-patient re-use in the home environment and multi-
patient re-use in the hospital/institutional environment.
Clinical benefits
The clinical benefit of vented masks is the provision of effective therapy
delivery from a therapy device to the patient.
Intended patient population/medical conditions
Obstructive pulmonary diseases (eg, Chronic Obstructive Pulmonary
Disease), restrictive pulmonary diseases (eg, diseases of the lung
parenchyma, diseases of the chest wall, neuromuscular diseases), central
respiratory regulation diseases, obstructive sleep apnoea (OSA) and
obesity hypoventilation syndrome (OHS).

2
GENERAL WARNINGS
•The mask must be used under qualified supervision for users who
are unable to remove the mask by themselves. The mask may not
be suitable for those predisposed to aspiration.
•The vent must be kept clear.
•The mask should only be used with CPAP or bilevel devices
recommended by a physician or respiratory therapist.
•The mask should not be used unless the device is turned on. Once
the mask is fitted, ensure the device is blowing air. Explanation:
CPAP and bilevel devices are intended to be used with special
masks (or connectors) which have vent holes to allow continuous
flow of air out of the mask. When the device is turned on and
functioning properly, new air from the device flushes the exhaled
air out through the mask vent holes. However, when the device is
not operating, insufficient fresh air will be provided through the
mask, and the exhaled air may be rebreathed. Rebreathing of
exhaled air for longer than several minutes can, in some
circumstances, lead to suffocation. This applies to most models of
CPAP or bilevel devices.
•Follow all precautions when using supplemental oxygen.
•Oxygen flow must be turned off when the CPAP or bilevel device
is not operating, so that unused oxygen does not accumulate
within the device enclosure and create a risk of fire.
•Oxygen supports combustion. Oxygen must not be used while
smoking or in the presence of an open flame. Only use oxygen in
well ventilated rooms.
•At a fixed rate of supplemental oxygen flow, the inhaled oxygen
concentration varies, depending on the pressure settings, patient
breathing pattern, mask, point of application and leak rate. This
warning applies to most types of CPAP or bilevel devices.The
technical specifications of the mask are provided for your clinician
to check that they are compatible with the CPAP or bilevel device.
If used outside specification or if used with incompatible devices,
the seal and comfort of the mask may not be effective, optimum
therapy may not be achieved, and leak, or variation in the rate of
leak, may affect the CPAP or bilevel device function.
•Discontinue using this mask if you have ANY adverse reaction to
the use of the mask, and consult your physician or sleep therapist.

English 3
•Using a mask may cause tooth, gum or jaw soreness or aggravate
an existing dental condition. If symptoms occur, consult your
physician or dentist.
•As with all masks, some rebreathing may occur at low CPAP
pressures.
•Refer to your CPAP or bilevel device manual for details on
settings and operational information.
•The mask is not intended to be used simultaneously with
nebulizer medications that are in the air path of the mask/tube.
•Remove all packaging before using the mask.
Note: For any serious incidents that occur in relation to this device, these
should be reported to ResMed and the competent authority in your
country.
Using your mask
When using your mask with ResMed CPAP or bilevel devices that have
mask setting options, refer to the Technical specifications section in this
user guide for mask selection options.
For a full list of compatible devices for this mask, see the Mask/Device
Compatibility List at ResMed.com/downloads/masks.
Notes:
•This mask is not compatible for use with ResMed AutoSet CS™ 2 and
VPAP™ Adapt SV devices.
•SmartStart may not operate effectively when using this mask with
some CPAP or bilevel devices that have this feature.
•If you experience nasal dryness or irritation, using a humidifier is
recommended.
Fitting
1. Hold the pillows away from your nose ensuring that the pillow size
(eg, M) with the left (L) and right (R) indicators are correctly facing
towards you then guide the nasal pillows into your nostrils (L into your
left nostril, R into your right nostril). Pull the headgear over your head
by holding the bottom band and stretching it around the back of your
head. The top band should sit comfortably on top of your head.
Tip! There are raised logos on top of the frame so you can feel the
correct way up when fitting in the dark.

4
2. Move the mask away from your face then place it back to get a
comfortable fit. Ensure the nasal pillows fit securely into your nostrils
with both pillows positioned upright.
3. Finally, connect the end of the mask tubing into your device air tubing.
Your mask is now fitted and ready to use. When the device is running,
a light breeze should be felt through the vent. To inspect the vent
place a finger close but not over the entire vent area.
Adjustment
To fix any mask leaks, adjust the headgear by pulling the headgear
through the buckle. Adjust only enough for a comfortable seal and do not
overtighten. You may need to adjust the headgear as it stretches over
time.
Removal
To take off your mask system, pull the mask and headgear by the split-
band, up and over your head.
Disassembly
1. Holding the top of the mask tubing, squeeze and pull the pillows away
from the mask frame.
2. Unhook the headgear from the stabiliser by pulling on the end cap to
reveal the buttonhole.
3. Slide the headgear off the end of the stabiliser.
Reassembly
1. With the grey side facing out, insert each end of the headgear band
over the stabilisers through the buttonholes. Secure in place by
wrapping each band end up and around the nodes. Holding the split
bands, pull the headgear from the stabiliser to ensure it is tightly
secure around the nodes. Ensure the headgear band is not twisted.
2. Attach the pillows to the mask frame by inserting the top and bottom
clips into the correct slots (shorter clip into top slot, longer clip into
bottom slot) on the mask frame. Your mask is now reassembled.
3. Ensure the inner walls of the nasal pillows are not compressed or
collapsed. If they are, squeeze each nasal pillow so they return to the
correct shape.

English 5
Cleaning your mask at home
Your mask and headgear should only be gently handwashed. The mask
vent may discolour over time due to dust. Follow the cleaning instructions
in this guide to maintain performance and safety of the mask.
WARNING
Always follow cleaning instructions and use mild soap. Some
cleaning products may damage the mask, its parts and their function,
or leave harmful residual vapours that could be inhaled if not rinsed
thoroughly.
CAUTION
•If any visible deterioration of a system component is apparent
(cracking, crazing, tears etc), the component should be discarded
and replaced.
•Avoid connecting flexible PVC products (eg, PVC tubing) directly
to any part of the mask. Flexible PVC contains elements that can
be detrimental to the materials of the mask, and may cause the
components to crack or break.
•When fitting the mask, do not overtighten the headgear as this
may lead to skin redness or sores around the mask cushion.
•Do not iron the headgear as the material is heat sensitive and will
be damaged.
Daily/After each use:
•Disassemble the pillows from the frame according to the disassembly
instructions.
•Thoroughly clean the separated mask components (excluding
headgear), by gently rubbing in warm (approximately 30°C) water
using mild soap.
•To optimise the mask seal, facial oils should be removed from the
pillows after use.
•Use a soft bristle brush to clean the vent.
•Inspect each component and, if required, repeat washing until visually
clean.
•Rinse all components well with drinking quality water and allow to air
dry out of direct sunlight.

6
•When all components including the vent are dry, reassemble
according to the reassembly instructions.
Weekly:
•Soak the headgear in warm water with a mild liquid detergent.
•Hand wash the headgear with a soft bristle brush.
•Thoroughly rinse the headgear under running water.
•Leave the headgear to air dry out of direct sunlight.
Reprocessing the mask between patients
Reprocess this mask when using between patients. Reprocessing
instructions are available on ResMed.com/downloads/masks.
Troubleshooting
Problem/possible cause
Solution
Pillows won’t seal properly, mask is uncomfortable or causes red marks
Pillows may have been fitted
incorrectly, adjusted incorrectly
or the headgear is fitted
incorrectly.
Check that the nasal pillows with the left (L) and right
(R) indicators are inserted correctly (L into your left
nostril, R into your right nostril). Carefully follow the
fitting instructions. Readjust the headgear to ensure it
is fitted comfortably.
Inner wall position of one or
both pillows is incorrect.
Squeeze pillow sides to release inner wall. The correct
position is shown in the reassembly instructions.
Pillows are the wrong size. Talk to your clinician.
Pillows may be dirty. Clean pillows according to the instructions.
Headgear is too loose. Adjust the headgear by pulling the headgear through
the buckle. Adjust only enough for a comfortable seal
and do not overtighten. You may need to adjust the
headgear as it stretches over time.
Vent is blocked or
dirty/discoloured.
If the vent requires cleaning, use a soft bristle brush.
The vent may discolour over time and this is not a
safety concern. Follow the cleaning instructions in this
guide to maintain performance and safety of the mask.
Vent is wet. Ensure the vent is dry after cleaning and in the case of
excess condensation.

English 7
Problem/possible cause
Solution
Mask too noisy
System is assembled incorrectly. Disassemble the mask, then reassemble according to
the instructions.
System is leaking air. Refit or reposition your mask. Adjust your headgear.
Check your mask is assembled correctly.
Technical specifications
Pressure-flow curve
The mask contains passive venting to protect against
rebreathing. As a result of manufacturing variations, the vent
flow rate may vary.
Pressure
(cm H2O)
Flow
(L/min)
4
20
8
29
12
37
16
43
20
49
Dead space information
Physical dead space is the empty volume of the mask to the
end of the swivel. Using the large cushions it is 123 mL.
Therapy pressure
4 to 20 cm H2O
Resistance
Drop in pressure measured (nominal)
at 50 L/min: 0.4 cm H2O
at 100 L/min: 1.4 cm H2O
Sound
DECLARED DUAL-NUMBER NOISE EMISSION VALUES in
accordance with ISO 4871. The A-weighted sound power
level of the mask is 21 dBA, with uncertainty of 3 dBA. The
A-weighted sound pressure level of the mask at a distance
of 1 m is 13 dBA, with uncertainty of 3 dBA.
Environmental
conditions
Operating temperature: +5°C to +40°C
Operating humidity: 15% to 95% non-condensing
Storage and transport temperature: -20°C to +60°C
Storage and transport humidity: up to 95% relative humidity
non-condensing

8
Gross dimensions
590 mm (H) x 149 mm (W) x 30 mm (D)
Mask fully assembled with short tube assembly (no
headgear)
Mask setting options
For S9: Select 'Pillows'
For other devices: Select 'SWIFT' (if available), otherwise
select 'MIRAGE' as the mask option.
Note: The manufacturer reserves the right to change these specifications without notice.
Storage
Ensure that the mask is thoroughly clean and dry before storing it for any length of time.
Store the mask in a dry place out of direct sunlight.
Disposal
This mask and packaging does not contain any hazardous substances and may be disposed
of with your normal household refuse.
Symbols
The following symbols may appear on your product or packaging:
Nasal Pillows mask Polypropylene recyclable
Size - Extra small Size - Small
Size - Medium Size - Large
Importer Medical device
Not made with natural rubber latex
See symbols glossary at ResMed.com/symbols.
Consumer warranty
ResMed acknowledges all consumer rights granted under the EU Directive 1999/44/EC and
the respective national laws within the EU for products sold within the European Union.

简体中文 1
简体中文
AirFit™ P10
鼻枕系统
感谢您选用AirFit P10产品。 本文件提供AirFit P10和AirFit P10 for
Her面罩的使用者说明，而在本手册内此两种制品总称为AirFit P10。AirFit
P10有蓝色头带，AirFit P10 for Her有粉色头带。
使用本手册
使用前请阅读手册的全部内容。在按照手册的内容进行操作时，请参照本
手册的首页和底页的图示说明。
设计用途
AirFit P10通过持续气道正压(CPAP)或双水平装置等的气道正压通气(PAP)
装置，以无创方式向患者提供气流。
AirFit P10：
•供体重超过30千克，按医嘱须接受气道正压治疗的患者使用。
•可供一位病人在家中重复使用和供多位病人在医院/诊所中重复使用。
临床效益
通风面罩的临床益处是提供从治疗设备到患者的有效治疗。
预期的患者人群/医疗状况
阻塞性肺部疾病（例如：慢性阻塞性肺疾病）、限制性肺部疾病（例如：
肺实质疾病、胸壁疾病、神经肌肉疾病）、中枢呼吸调节疾病、阻塞性睡
眠呼吸暂停（OSA）和肥胖低通气综合征（OHS）。
一般性警告
•无法自己摘下面罩的使用者，须在合格的监护下使用此面罩。此面
罩不适合容易出现误吸情况的患者使用。
•通气孔必须保持通畅。
•此面罩只能与医生或呼吸治疗师推荐使用的气道正压或双水平装置
配合使用。
•装置启动后才能使用面罩。面罩配戴好后，必须确定装置正在输送
空气。说明：气道正压或双水平装置需要配合特殊面罩(或接头)一

2
起使用，这些面罩带有通气孔可以保证空气能持续地排出面罩。当
装置启动并运行正常时，来自装置的新鲜空气会通过面罩通气孔将
呼出的气体排出面罩。但是当装置不运行时，将无法向面罩提供足
够的新鲜空气，呼出的气体将会被再次吸入。重新吸入呼出的
气体，如果超过数分钟，则有可能造成患者窒息。此情形适用于大
多数型号的气道正压或双水平装置。
•输送氧气时，须遵循所有安全保护措施。
•CPAP或双水平装置未运行时，必须关闭供氧气流。只有这样做，未
使用的氧气才不会在装置内部聚集，从而产生火灾危险。
•氧气会助燃。吸烟或面对明火时，严禁使用氧气。仅在通风条件良
好的屋内使用氧气。
•在补充供氧流量固定不变的情况下，由于压力设置、患者的呼吸模
式、面罩、配戴位置和泄漏程度的不同，吸入的氧气浓度可能会有
所不同。此警告适用于大多数型号的CPAP或双水平装置。面罩的技
术规格乃供您的医生检查确定它们可以和气道正压或双水平装置兼
容并用。如果未按规格使用，或者和不兼容的装置配用，可能影响
面罩的密封性和舒适度，而无法获得理想的治疗效果，漏气或漏气
速度异常也可能会影响气道正压或双压水平装置功能。
•使用面罩后若出现任何不良反应，请停止使用面罩，并咨询您的医
生或睡眠治疗师。
•使用面罩可能会导致牙齿、牙龈或面颊疼痛或加重现有牙齿病症。
如果出现这些症状，请向您的医生或牙医咨询。
•和所有的面罩一样，气道正压压力低时，可能会出现某种程度的再
吸入。
•有关设定的详细内容与操作信息，请参阅您的气道正压或双水平装
置手册。
•面罩不能与面罩/通气管内的雾化药物同时使用。
•使用面罩前请先除去所有包装。
备注：如发生与本设备有关的任何严重事故，应向ResMed和您所在国家或
地区的主管当局报告。
使用面罩须知
与配有面罩设置选项的瑞思迈
气道正压或双水平装置一起使用面罩时，请参阅用户指南中的技术规格部
分，了解面罩选用范围。
本款面罩的兼容装置完整清单，请见ResMed.com/downloads/masks。

简体中文 3
备注：
•此面罩不能与瑞思迈的AutoSet CS™ 2与VPAP™ Adapt SV
装置兼容并用。
•和一些具备SmartStart功能的气道正压或双压水平装置并用时，装置的
SmartStart功能可能无法有效运行。
•假如您的鼻腔出现干燥或不适的情形，建议您使用增湿器。
配戴
1. 握住鼻枕，放在鼻子上面，试一下鼻枕尺寸(例如：中型)，确保左右标
志是否正确面对您，然后把鼻枕插入鼻孔(左边插入左鼻孔，右边插入右
鼻孔)。握住下部束带并把它箍在脑后，然后把头带拉过头顶。上部束带
应舒适地套在头顶。
提示！面罩框上有凸起的标志，因此在黑暗中配戴时可以感觉到正确的
位置。
2. 把面罩从面部拿下，然后再放回去，确保配戴舒适。确保鼻枕牢固地放
入鼻孔，鼻枕两边的位置向上。
3. 最后，把面罩端部管路与装置的呼吸管路连接。现在已配戴好面罩并准
备就绪。装置运行时，透过通气孔可感觉到微风。把手指靠近通气孔，
但不要遮盖住整个通气孔，即可检查通气孔的运行情况。
调整
若要调整面罩空隙，将头带通过带扣拉紧即可。调整头带松紧至舒适服贴
即可，无需过紧。头带使用一段时间后或会松开，须进行调整。
取下
若要取下面罩系统，把面罩和头带的对开束带向上拉过头顶即可。
拆卸
1. 握住面罩管路顶部，捏压管路并把鼻枕往外拔出面罩框。
2. 拉动端盖，露出扣眼，从稳定器上取下头带。
3. 将头带滑离稳定器的末端。
重新组装
1. 灰色一侧朝外，把头带束带的每个末端插入稳定器的扣孔。在扣孔周围
系紧每条束带，固定到位。握住对开束带，在稳定器位置拉紧头带，确
保在扣孔周围系牢。确保头带束带没有扭曲。

4
2. 把鼻枕连接到面罩框上，需要把上、下固定夹插入面罩框上的正确插口(
较短的固定夹插入上部插口，较长的固定夹插入下部插口)。现在面罩被
重新组装好。
3. 确保鼻枕的内壁未被挤压或萎陷。如果受到挤压或凹陷，捏压每个
鼻枕，使之恢复原状。
家中清洁面罩须知
用手轻轻地清洗面罩和头带。一段时间后，由于灰尘，通气孔可能会
褪色。请遵循本指南的清洁说明，维护面罩的性能和安全。
警告
请遵循清洁说明并使用温和肥皂。如果不彻底冲洗干净，某些清洁产品可
能会损坏面罩及其部件和功能，或者会残留可能被患者吸入的有害残余气
体。
注意事项
•系统组件若出现明显变坏情形(例如破裂、纹裂或撕裂等)，则应予
以抛弃并更换新组件。
•避免将柔性聚氯乙烯产品(例如柔性聚氯乙烯软管)直接连接到面罩
的任何部分。柔性聚氯乙烯包含对面罩原料可能有害的成分，并可
能导致组件破裂或碎裂。
•佩戴面罩时，头带不要束得过紧，否则面罩护垫周围皮肤可能发红
或疼痛。
•不得熨烫头带，因为头带的材料对热度敏感，会因而损坏。
每日/每次使用后清洁：
•按照拆除说明从面罩框上拆除鼻枕。
•彻底清洗拆开的面罩组件(不包括头带)，在温度适宜（约30°C）的温和
肥皂水中轻轻揉搓。
•为获得最佳的面罩密封效果，每次使用后应除去鼻垫上的面部油脂。
•请用柔软毛刷清洁通气孔。
•检查每一个组件，必要时重复清洗，直到看上去干净为止。
•使用饮用水质量的清水充分冲洗所有组件，置于透风处荫干，避免日光
曝晒。
•当所有元件(包括通风孔)干燥时，请按照组装说明重新组装。

简体中文 5
每周清洁：
•在温水和温和洗涤液中浸泡头带。
•用软毛刷刷洗头带。
•用流动水彻底冲洗头带。
•把头带晾干，避免阳光直射。
不同患者共用面罩的再处理方式
病人之间使用时，重新处理此面罩。重新处理说明可见
ResMed.com/downloads/masks网页。
故障排除
问题/可能原因
解决方法
鼻枕未适当密封，面罩配戴不舒适或引致红斑
鼻枕可能配戴不当、
调整不当或头带配戴
不当。
检查鼻枕左右标志是否插入正确(左边(L)插入
左鼻孔，右边(R)插入右鼻孔)。仔细遵循配戴说明
。重新调整头带，确保配戴舒适。
一方或双方鼻枕的内
壁位置错误。
捏压鼻枕两侧，放松内壁。正确位置请看组合说明
图标。
鼻枕尺寸错误。 请咨询您的医生。
鼻枕可能污脏。 依照说明清洁鼻枕。
头带太松。 将头带通过带扣拉紧即可进行调整。调整头带松紧
至舒适服贴即可，无需过紧。头带使用一段时间后
或会松开，须进行调整。
通气孔堵塞、脏污或
褪色。
如果需要清洗通气孔，请用软毛刷。一段时间后，
通气孔可能会褪色，但不会产生安全问题。请遵循
本指南的清洁说明，维护面罩的性能和安全。
通气孔潮湿。 确保清洁后将通风孔擦干，以及在水汽过度凝结时
保持通风孔干爽。
面罩噪音太大
系统组合错误。 拆开面罩，然后依照说明重新组合。
系统泄露空气。 重新配戴面罩或调整面罩位置。调整头带。检查确
定面罩组合正确。

6
技术规格
气流压力曲
线
面罩具有被动通气功能，可防止再吸入。由于生产制造的差
异，排气孔流速可能会有差异。
压力
(cm H
2
O)
气流
(升/分钟)
4 20
8 29
12 37
16 43
20 49
死腔信息
实质死角乃是面罩至万向轴末端的空间容积。使用大尺寸
护垫，其容积为123毫升。
治疗压力
4至20 cm H2O
阻力
测量到的压力下降（标称值）
处于50升/分钟0.4 cm H2O
处于100升/分钟1.4 cm H2O
噪声
声明的双数噪音排放值符合ISO 4871标准。面罩的A加权声功
率为21 分贝，误差为3 分贝。在1 米的距离内，面罩的A加权
声压为13 分贝，误差为3分贝。
环境条件
工作温度：+5°C 至+40°C
工作湿度：15%至95%，非凝结
存放和运输温度：-20℃至+60℃
储存与运输湿度：最高不超过95%相对湿度，非冷凝
外部尺寸
590毫米(高)x149毫米(宽)x30毫米(厚)
连接短管组件的完全组装面罩(无头带)
面罩设定选
择
用于S9：
选择“鼻枕”。
其它装置：
选择“SWIFT”(若提供)，否则请选“MIRAGE”。
备注： 制造商保留在不另行通知的情况下，修改这些规格的权利.
储存
储存前，无论储存时间长短，都需彻底清洁面罩，并保持干燥。面罩需储
存于干燥避光处。

简体中文 7
废弃
此面罩和包装不含任何有害物质，可当作一般家庭废物处置。
符号
产品上或包装上可能出现下列符号：
鼻枕面罩 聚丙烯可回收
尺寸 - 加小号 尺寸 - 小号
尺寸 - 中号 尺寸 - 大号
进口商 医疗设备
不使用天然乳胶制造
请参阅ResMed.com/symbols上的符号词汇表。
顾客保证
瑞思迈承认根据欧盟理事指令1999/44/EG以及欧盟组织内个别国家法对于
在欧盟地区内销售之产品所定的全部消费者权利。

繁體中文 1
繁体中文
AirFit™ P10
鼻枕系統
感謝您選用 AirFit P10。本文件提供 AirFit P10 和AirFit P10 for Her 面罩的
使用者說明，而在本手册內此兩種製品總稱爲 AirFit P10。AirFit P10 有藍
色頭帶，女式 AirFit P10 for Her 有粉色頭帶。
使用本手冊
使用前請閱讀手冊的全部內容。在按照手册的內容進行操作時，請參照本
手册的首頁和底頁的圖示說明。
設計用途
AirFit P10 透過單陽壓或雙陽壓裝置，以非侵襲性方式向患者提供氣流。
AirFit P10 產品：
•供體重超過 30 公斤，按醫囑須接受氣道正壓治療的患者使用
•供一位患者在家中重複使用和供多位患者在醫院/診所中重複使用。
臨床效益
通風面罩的臨床益處是提供從治療設備到患者的有效治療。
預期的患者人群/醫療狀況
阻塞性肺部疾病（例如：慢性阻塞性肺疾病）、限制性肺部疾病（例如：肺
實質疾病、胸壁疾病、神經肌肉疾病）、中樞呼吸調節疾病、阻塞性睡眠呼
吸暫停（OSA）和肥胖低通氣綜合徵（OHS）。
一般性警告
•無法自己摘下面罩的使用者，須在合格的監護下使用此面罩。此面罩不
適合容易出現誤吸情況的患者使用。
•通氣孔必須保持通暢。
•此面罩只能與醫生或呼吸治療師推薦使用的單陽壓或雙陽壓裝置配合使
用。
•裝置啟動後才能使用面罩。面罩配戴好後，必須確定裝置正在輸送空
氣。解釋：單陽壓和雙陽壓裝置需要配合特殊面罩(或接頭)一起使用，
這些面罩帶有通氣孔，可以保證空氣能持續地排出面罩。當裝置啟動並