National Alloy User manual

Assembly Instrucon
Telephone [phone]
Fax [phone]
www.NationalOfficeFurniture.com
Part # 3111376
Rev, -
Printed in U.S.A
© 2018 Kimball International, Inc.
Alloy
Vertical Storage
Spacer Assembly
Proper product installation, in accordance with these instructions, is the responsibility of the installing agent.
If you have any questions concerning these instructions, please call National Customer Service 800.482.1717.
Figure A:
Top Spacer
Side Piece
Lower Base Spacer
Electrical Pass Through
Package Contents
1Lay out pieces on the ground and locate mounng hardware supplied.
(Figure A)
Item Qty
M5.5–1.8 X 13MM 24
ZINC PL PHIL/SQ COMBO
#8 X 3/4” PHILLIPS 6
SELF TAPPING SCREW
2Place and install the lower base spacer piece to both side pieces and
secure with eight (8) Self-Tapping Screws. Four (4) screws used on front
face and four (4) screws used on back face. (Figure B)
Note: If applicable make sure that both electrical pass through
holes are in alignment with each other and biased towards the
boom base spacer. (See gure A for reference)
Figure B:

Assembly Instrucon
Telephone [phone]
Fax [phone]
www.NationalOfficeFurniture.com
Part # 3111376
Rev, -
Printed in U.S.A
© 2018 Kimball International, Inc.
Alloy
Vertical Storage
Spacer Assembly
Proper product installation, in accordance with these instructions, is the responsibility of the installing agent.
If you have any questions concerning these instructions, please call National Customer Service 800.482.1717.
Figure C:
4Place and install the top spacer piece to both side pieces and
secure with eight (8) Self-Tapping Screws. Four (4) screws used on front
face and four (4) screws used on back face. (Figure D)
Figure D:
3Finish securing lower base with side pieces by installing four (4) screws
through pre located holes on boom face. (Figure C)

Assembly Instrucon
Telephone [phone]
Fax [phone]
www.NationalOfficeFurniture.com
Part # 3111376
Rev, -
Printed in U.S.A
© 2018 Kimball International, Inc.
Alloy
Vertical Storage
Spacer Assembly
Proper product installation, in accordance with these instructions, is the responsibility of the installing agent.
If you have any questions concerning these instructions, please call National Customer Service 800.482.1717.
5Finish securing top spacer piece with side pieces by installing four (4)
screws through pre located holes on inside of top piece. (Figure E)
Figure E:
Figure F:
6If applicable install rubber grommet material around both electrical pass
through holes. (Figure F)

Assembly Instrucon
Telephone [phone]
Fax [phone]
www.NationalOfficeFurniture.com
Part # 3111376
Rev, -
Printed in U.S.A
© 2018 Kimball International, Inc.
Alloy
Vertical Storage
Spacer Assembly
Proper product installation, in accordance with these instructions, is the responsibility of the installing agent.
If you have any questions concerning these instructions, please call National Customer Service 800.482.1717.
Figure G:
7Bring in storage unit to be installed with spacer assembly and place back
to back. Run down and secure six (6) #8 X 3/4” Phillips self tapping screws
to fasten spacer assembly to back of cabinet. (Figure G & H)
Figure H:

Assembly Instrucon
Telephone [phone]
Fax [phone]
www.NationalOfficeFurniture.com
Part # 3111376
Rev, -
Printed in U.S.A
© 2018 Kimball International, Inc.
Alloy
Vertical Storage
Spacer Assembly
Proper product installation, in accordance with these instructions, is the responsibility of the installing agent.
If you have any questions concerning these instructions, please call National Customer Service 800.482.1717.
8Apply two sided tape strips to the open face edges of the spacer unit.
Locate tape in approximate posion as shown. (Figure I)
Figure I:
Figure J:
9Bring in second storage unit and place on open side of spacer up against
two sided tape to secure. Figure (J)