REVELL P-51D Mustang User manual

Before commencing assembly,please read these instructions thoroughly.
SAFETY PRECAUTIONS
This radio control model is not a toy!
lFirst-time builders should seek advice from people having building
experience in order to assemble the model correctly and to produce
its performance to full extent.
,
lAssemble this kit only in places out of children s reach!
lTake enough safety precautions prior to operating this model.
,
You are responsible for this models assembly and safe operation!
lAlways keep this instruction manual ready at hand for quick
reference,even after completing the assembly.
SPECIFICATION
P-51D Mustang

22
REQUIRED FOR OPERATION (Purchase separately)REQUIRED FOR OPERATION (Purchase separately)
TOOLS REQUIRED ( Purchase separately)TOOLS REQUIRED ( Purchase separately)
BEFORE YOU BEGINBEFORE YOU BEGIN
Sharp Hobby Knife Phillips Screw Driver Awl
Needle Nose Pliers Wire Cutters Scissors
Read through the manual before you begin ,so you will have an overall idea of what to do.
Check all parts .if you find any defective or missing parts .contact your local deater.
Symbols used throughout this instruction manual,comprise.
11
22
33
.
.
.
Warning!
£¡
Cut off shaded portion.
Ensure smooth non-binding
movement while assembling.
Must be purchased
separately!
Pay close attention
here!
Drill holes with the specified
Diameter(here:2mm)
2mm
Assemble left and right
Sides the same way.
Apply instant glue
(CA glue,super glue).
Apply epoxy glue.
BA
Cut off excess.
!
Do not overlook this symbol.
11
A minimum 6 channel radio for airplanes (with 10 servos).
And dry batteries.
CAUTION: Only use a minimum 6 channel radio for
airplanes! (No other radio may be used!)
!
12 AA-size Batteries
A minimum 6 channel
transmitter for airplanes.
22
For handing the radio properly.refer to its instruction manual.
Engine and Muffler
Muffler
Glow plug
33
Purchase a propeller that
will match your engine
44
Silicone Tube Fuel Filter
55
required for engine starting Glow engine fuel only.
WARNING: Normal gasoline cannot
be used with glow engines.
!
Fuel Pump Plug Wrench
33
Glue
66
Instant glue Epoxy Glue
33
Other equipment for enhancing
airplane operation & perormance
77
12V Battery (for starter)
Engine Starter
Propeller splinner
MA
80-100 cc gas engine
odel irplane engine

!
Accessory list for this page.
3
Install the aileron
2
1
5
4
Install the servo
33
BA
Install the nylon control horn and
connect the linkage
Make sure hings are
mounted in the same line
-----------8
Pin hings
BA
Install the servo
Epoxy pin hings to aileron steadily
M3X30mm Screw
- - - - 4
Horn
- - - - 4 - - - - 2
M4X35mm Screw
- - - - 4
M2X8mm Screw
- - - - 8
Hinge
-----6
Rod (2.5x85mm)
- - - - 4
Securely glue together. If comingoff during flights,you'll
lose control ofyour airplane which leads to accidents!
Warning!Warning!
Flap Aileron
Tailing edge
Aileron
2mm
Connecting rod head
- - - - 4
M3X40mm Screw
- - - - 4
- - - 8
M3X25mm Screw
- - - - 6
Rod adjuster
---8
Pin hings
Hinge
-----6
M3X30mm Screw
- - - - 4
Horn
- - - - 4
- - - - 2
M4X35mm Screw
- - - - 4
M2X8mm Screw
- - - - 8
Rod (2.5x85mm)
- - - 4
Connecting rod head
- - - - 4
M3X40mm Screw
- - - - 4
- - - 8
M3X25mm Screw
- - - - 6
Rod adjuster

!
Accessory list for this page.
8
710
9
44
6
Install the main landing gear
Install the landing gear
LL
RR
502
C.A
C.A
Install the main landing gear
AB
LL
RR
3X3mm screw
5.2mm Collar
3X20mm Tp screw
- - - - - 8
5X45mm Axletree
- - - - - 2
- - - - - 2
- - - - - 2
4X4mm screw
- - - - - 2
Play wood
Play wood
- - - - - - - - - - - -2
- - - - - - - - - - - -4
Pleas notice the inner diameter for each
side of the pressure reduction inlet.
Please insure the sealing of the retract
system before flight .
Retainer
Rod adjuster
2X8mm screw
- - - - - 1
- - - - - 1
- - - - - 1
Rod (1.8X80mm)
- - - - - 1
2000mm Air line
- - - - - 2
365MM
BA
4
M3X20mm Cap screw
4
3mm Lock Nut
LL
RR
Install the main landing gear
Install the drop tank. (P51D Miss Americal
design does not include drop tank)
3X3mm screw
5.2mm Collar
3X20mm Tp screw
- - - - - 8
5X45mm Axletree
- - - - - 2
- - - - - 2
- - - - - 2
4X4mm screw
- - - - - 2
Retainer
Rod adjuster
2X8mm screw
- - - - - 1
- - - - - 1
- - - - - 1
Rod (1.8X80mm)
- - - - - 1
2000mm Air line
- - - - - 2
4
M3X20mm Cap screw
4
3mm Lock Nut

!
Accessory list for this page.
13
12 15
14
55
11
Epoxy pin hinges to elevator
Epoxy elevator hinges to horizontal tail
Epoxy pin hings to rudder
B
A
Make sure hings are
mounted in the same line
-----------3
Pin hings
Warning!
£¡
!
Securely glue together ,if c oming
off during . You will lose control
of your airplane which leads to accidents!
B
A
Install the rudder
AB
Rod adjuster
Connecting rod head
- - - - 2
- - - - 2
Horn
- - - - 2
- - - 4
M3X30mm Screw
- - - - 6
M4X35mm Screw
- - - - 4
M2X8mm Screw
- - - - 4
Rod (2.5x85mm)
- - - - 2
Tailing edge
Rudder
4mm
Securely glue together. If coming off during flights,you'll
lose control ofyour airplane whichleads to accidents!
Warning!Warning!
Rod adjuster
Connecting rod head
- - - - 2
- - - - 2
Horn
- - - - 2
- - - 4
M3X30mm Screw
- - - - 6
M4X35mm Screw
- - - - 4
M2X8mm Screw
- - - - 4
Rod (2.5x85mm)
- - - - 2
-----9
Pin hings
BA
Make sure hings are
mounted in the same line
-----------6
Pin hings
Install the elevator servos

Rod
10mm tube
- - - - - - 2
- - - - - - 2
Rod adjuster
Connecting rod head
- - - - 2
- - - - 2
Horn
- - - - 2
M3X45mm Screw
- - - - 3
M2X8mm Screw
- - - - 2
Set Nut
- - - - - - - 3
!
Accessory list for this page.
18
17 20
19
66
16
Rudder . Connect the linkage
rod to the horn
12
M3X20mm Cap screw
12
3mm Lock Nut
4.2mm
Fuel tankFuel tank
Engine Box Preparation
Installation the engine
B
A
- - - - 1
- - - - 3
3.2mm Collar
3.2mm Nylon Collar
3X3mm Screw
- - - - 3
6X9 screw
- - - - 1
- - - - 1
3.2mm Rocker
- - - - - 1
6mm nut
Aluminium tube
Rod adjuster
- - - - - 2
Rod - - - - - 2
- - - - - 2
1600mm Steel wire
- - - - - 2
3X3mm Screw
- - - - 1
Install the tail wheel
Install the tail wheel
- - - - 1
- - - - 3
3.2mm Collar
3.2mm Nylon Collar
3X3mm Screw
- - - - 4
6X9 screw
- - - - 1
- - - - 1
6mm nut
66
3.2mm Rocker
- - - - - 1
Aluminium tube
Rod adjuster
- - - - - 4
Rod - - - - - 4
- - - - - 4
1600mm Steel wire
- - - - - 2
Connecting rod head
- - - - 2
- - - - 2
Horn
M3X45mm Screw
- - - - 3
M2X8mm Screw
- - - - 2
Set Nut
- - - - - - - 3
12
M3X20mm Cap screw
12
3mm Lock Nut
2
M4X20mm Cap screw
4mm Blind Nut
- - - - - - 4
4mm Blind Nut
- - - - - - 2
2
M4X20mm Cap screw

!
Accessory list for this page.
23
22
24
7
21
Assemble horizontal tail,vertical tail,
tail gear separately
Epoxy the horizontal tail to fuselage
25
Mount the main wing on the fuselage
Securely glue together
,if coming off during flights.
You lose control of your airplane
which leads to accidents!
AA
AA
securely glue together,if coming off
during flights, you'll lose control of your
airplane which leads to accidents.
M4X10mm screw
- - - - - - 2
8mm nylon Nut
- - - - - 4
Assemble the servos and switch in the fuselage
Aluminium tube
Rod adjuster 2X8mm screw
- - - - - 2 - - - - - 2
Rod
- - - - - 2
- - - - - 2
Assemble the canopy
8mm nylon Nut
- - - - - 4
M4X10mm screw
- - - - - - 2
Aluminium tube
Rod adjuster
2X8mm screw
- - - - - 2
- - - - - 2
Rod
- - - - - 2 - - - - - 2

!
Accessory list for this page.
27
8
26
Install the cowling
Assemble the canopy
M3X25mm screw
3mm Washer
- - - - - - 2
- - - - - - - - - 2
M3X15mm screw
3mm Washer
- - - - - - 6
- - - - - - - - - 6
M3X25mm screw
3mm Washer
- - - - - - 2
- - - - - - - - - 8
M3X15mm screw
- - - - - - 6

30
29
5
31
Centre of Gravity.
Adjust the travel of each control surface to the
values in the diagrams.
These values fit general flight capabilities.
Readjust according to your needs and flight level.
Adjust the travel of each control surface to the
values in the diagrams.
These values fit general flight capabilities.
Readjust according to your needs and flight level.
Never fly before checking the Cg s required position.
In order to obtain the CG specified ,reposition the
receiver and battery.
NEVER fly the model
without well balancing.
Warning!
!
28
AILERON
Adjustment.
Top view
Adjust the travel of each control surface to the
values in the diagrams.
These values fit general flight capabilities.
Readjust according to your needs and flight level.
Adjustment.
Adjustment.
99
CG
Top view
Side view
70mm
70mm
78mm
Top view
Side view
78mm
110-120mm
47mm
47mm