RH Baby&child 178 - 1/2 User manual

Made in Vietnam
Distributed in the U.S.A by:
Restoration Hardware Baby & Child
11640 Harrel St. Suite B
Mira Loma, CA 91752
www.rhbabyandchild.com
Distributed in Canada by:
Restoration Hardware Canada, Inc.
1500-1055 West Georgia Street
Vancouver, British Columbia V6E4N7
Model No: 178 - 1/2
INDUSTRIAL LOCKER TWIN/FULL BUNK BED
WARNING: Read all
Instructions before assembling
this product.
KEEP INSTRUCTIONS FOR
FUTURE USE.
Page 1 of 15
CUSTOMER SERVICE
If you are missing partsor have any questions about this product, contact us first. You can also order parts by writing to
the address above. Include the product model number, color, and a brief descriptionof the part.Call 1-800-762-1751.
CARE AND CLEANING
TOOLS AND INSTALLATION
Tools Necessary: Key Wrench (included).
NOTE : It may be easier to assemble productwith two people.
NOTE: When inserting bolts, turn clockwise until tight. Then loosen 1/2-3/4 of aturn. After crib is completely assembled,
return to each bolt and tighten.
DO NOT scratch or chip the finish. DO NOT use abrasive chemicals for cleaning.If the crib is to be stored, store in a cool
dry place and carefully package all original hardware to protect from loss.
All Restoration Hardware bunk bed are designed to meet the highest safety
standards and comply with all U.S. and Canadian bunk bed and cradles regulations.

Page 2 of 15
IMPORTANT SAFETY INFORMATION FOR BUNK BED
-
1. Follow the information on the WARNINGS appearing on the upper bunk end structure and on the
carton. DO NOT REMOVE WARNING LABEL FROM BED.
2. Always use the specified size mattress or mattress support, or both to help prevent the likelihood of
entrapment or falls.
3. Surface of mattress must be at least 5 inches below the upper edge of guardrails on top bunk.
4. Do not allow children under 6 years of age to use the upper bunk.
5. Prohibit more than one person on upper bunk.
6. Periodically check and ensure that the guardrails, ladder, and other components are in their proper
position, free from damage, and that all connectors are tight.
7. Do not allow horseplay on or under the bed and prohibit jumping on the bed.
8. Always use the ladder for entering and leaving the upper bunk.
9. Do not use substitute parts. Contact Restoration Hardware for replacement parts
10. Use of a night light may provide added safety precaution for a child using the upper bunk.
11. Use guardrails on both sides of the upper bunk.
12. If the bunk bed will be placed next to a wall, the guardrail that runs the full length of the bed
should be placed against the wall to prevent entrapment between the bed and the wall.
13. The use of water flotation mattresses is prohibited.
14. STRANGULATION HAZARD - Never attach or hang items to any part of the bunk bed that are
not designed for use with the bed: for example, but not limited to, hooks, belts, and jump ropes.
15. Keep these instructions for future reference.
Model No: 178 - 1/2
INDUSTRIAL LOCKER TWIN/FULL BUNK BED
TO HELP PREVENT SERIOUS OR FATAL INJURIES FROM
ENTRAPMENT OR FALLS
1. Never allow a child under 6 years on upper bunk.
2. - If bunk is Twin/Twin:
Use only mattress which is 75" long and 38" wide and 6" height on upper bunk,
and mattress which is 75" long and 38" wide and 10" height on lower bunk.
- If bunk is Full/Full:
Use only mattress which is 75" long and 53" wide and 6" height on upper bunk,
and mattress which is 75" long and 53" wide and 10" height on lower bunk.
3. Ensure thickness of mattress does not exceed 6"and mattress surface is at least
5 inches below upper edge of guardrails. Thickness for lower bunk is 10” high.
4. Use guardrails on both sides of upper bunk.
5. Prohibit horseplay on or under bed(s).
6. Prohibit more than one person on upper bunk.
7. Use ladder for entering and leaving upper bunk.
8. If the bunk bed will be placed next to a wall the guardrails that run the full length
of the bed should be placed against the wall to prevent entrapment between
the bed and the wall.
STRANGULATION HAZARD
9. Never attach or hang items to any part of the bunk bed that are not designed for
use with the bed, for example, but not limited to hooks, belts, and jump ropes.
DO NOT REMOVE THIS LABEL
WARNING

PARTS IDENTIFICATION
Page 3 of 15
(A) Left Post of Footboard
(x1 piece)
(C) Left Post of Headboard
(x1 piece)
(F) Front Side Rail (x1 piece) (G) Headboard Panel (x1 piece)
(I) Stretcher Bars (x4 pieces) (J) Top Platform Panels (x2 pieces)
(K) Base Bed (x1 set) (L) Ladder (x1 piece)
(B) Right Post of Footboard
(x1 piece)
(D) Right Post of Headboard
(x1 piece)
(H) Long Side Rails (x2 pieces)
(E) Back Side Rail (x1 piece)
Model No: 178 - 1/2
INDUSTRIAL LOCKER TWIN/FULL BUNK BED

Page 4 of 15
HARDWARE INCLUDED
TOOLS NEEDED
Phillips-head Screwdriver (not included)
ASSEMBLY INSTRUCTIONS
Note: - Bed must be assembled by at least two people.
- Please read instructions carefully before assembling bed.
- Use the parts and fittings list to identify each component.
- Keep all packing materials until assembly is complete to avoid loss of smaller parts.
- Do not completely tighten all bolts until all steps are finished.
1
2
3
4
5
6
7
8
9
10
8 pieces.
4 pieces.
2 pieces.
2 pieces.
Multi Wrench 13mm
Long Bolt M8x2-3/4"
8 pieces.Middle Bolt M8x1-1/2"
63 pieces.
32 pieces.
Small Bolt M8x1/2"
Short Bolt M8x21mm
1 piece.
1 piece.
1 piece.
Screw 8x30mm
Left Metal Bracket
( for footboard)
Right Metal Bracket
( for footboard)
Metal Bracket
( for Headboard)
Key Wrench 4mm
NO. ITEM DESCRIPTIONQTY.
Model No: 178 - 1/2
INDUSTRIAL LOCKER TWIN/FULL BUNK BED

NOTE:
The bunk has total of 4 orientations. Ladder (L) can be attached to left or right of the footboard, depending on where you would
like the Ladder (L) to be positioned, and on either side of drawers (use options below).
BACK SIDE RAIL CAN BE CONVERT TO LEFT OR RIGHT OF THE BUNK:
Page 5 of 15
E
E
E
Orientation 1 Orientation 2
Orientation 4
Orientation 3
Orientation 2, 3 Orientation 1, 4
E
E
Model No: 178 - 1/2
INDUSTRIAL LOCKER TWIN/FULL BUNK BED
E

Page 6 of 15
E
E
1
E
TO CONVERT THE BACK SIDE RAIL, FOLLOW THESE BELOW STEPS:
Remove the crossbars from the Back Side Rail (E),
by unscrewing the bolts/ screws found on back
side rail, as seen below.
Model No: 178 - 1/2
INDUSTRIAL LOCKER TWIN/FULL BUNK BED

Page 7 of 15
E
E
E
1
- Turn the open end of Back Side Rail (E) to the left.
- Re-attach the cross bars to the Back Side Rail (E)
by the original bolts/ screws.
- Tighten the bolts/ screws using Key Wrench (1) and
Philips Head Screwdriver (not included).
Model No: 178 - 1/2
INDUSTRIAL LOCKER TWIN/FULL BUNK BED

Install Left/ Right Posts of Footboard (A,B) to the Back Side Rail (E).
Insert Middle Bolts (4) and tighten with Multi Wrench (2).
Lay the Front Side Rail (F) to either the Headboard Panel (G).
Next, attach the 2 Left/ Right Posts of Headboard (C,D) to the
Headboard Panel (G) by inserting the Middle Bolts (4) into
the pre-drilled holes in each Headboard Panel (G) and Front
Side Rail (F). Tighten all bolts with Multi Wrench (2).
Page 8 of 15
STEP 1:
STEP 2:
E
4
2
F
G
Model No: 178 - 1/2
INDUSTRIAL LOCKER TWIN/FULL BUNK BED

Page 9 of 15
STEP 3:
Secure place the headboard to the Base Bed (K).
Attach metal brackets (10) to the posts (C,D) of
the headboard. Then insert Small Bolts (6), and
tighten with Multi Wrench (2), as seen below.
Model No: 178 - 1/2
INDUSTRIAL LOCKER TWIN/FULL BUNK BED
F
G
C
10
10
K
D
10
6
10

STEP 4:
Page 10 of 15
Model No: 178 - 1/2
INDUSTRIAL LOCKER TWIN/FULL BUNK BED
Secure place the footboard to the Base Bed (K).
Insert metal brackets (8, 9) to the posts (A, B) of
the footboard, as seen below.
STEP 5:
Attach metal brackets (8, 9) to the posts (A, B)
and Base Bed (K) using Small Bolts (6), and
tighten with Multi Wrench (2), as seen below.
E
9
9
8
8
K
6
2
6
2