RiverRidge 06-025 User manual

ASSEMBLY INSTRUCTIONS
RiverRidge® Ellsworth Floor Cabinet with Side Shelves
ITEM#: 06-025 White
ITEM#: 06-026 Espresso
ITEM#: 06-129 Taupe
ADULT ASSEMBLY REQUIRED
This product requires assembly by an adult because of small parts. Care should be taken
in unpacking and assembling this item to keep small parts away from children. During assembly
children should be kept away from the product due to possible risk of injury.
WARNING SEE FULL WARNING ON PAGE 2
Young children can be seriously injured or killed if furniture tips over. Don’t use
this item for a TV stand or place heavy objects on top of item. Always use
angle-braces or anchors to secure furniture to the wall.

THIS SHELF UNIT WILL HOLD UP TO 25 POUNDS PER SHELF OR A TOTAL OF 75 POUNDS.
DO NOT LOAD EACH SHELF WITH MORE THAN 25 POUNDS. OVERLOADING WITH MORE
THAN 25 POUNDS PER SHELF OR 75 POUNDS TOTAL WEIGHT MAY CAUSE DAMAGE TO
THE SHELF AND MAY CAUSE SERIOUS INJURY OR DEATH.

PARTS LIST
NO
QTY
DESCRIPTION
1
1PC
Top Board
2
1PC
Bottom Board
3
2PCS
Arch Shelf
4
1PC
Rear Support Board
5
1PC
Center Support Panel
6
1PC
Right Side Panel
7
1PC
Door
8
1PC
Shelf
9
1PC
Back Board
10
4PCS
Leg

NO
PARTS
QTY
DESCRIPTION
A
12PCS
Cam Bolt
B
12PCS
Cam Lock
C
16PCS
Wood Dowel
D
1PC
Knob
E
1PC
Machine Screw (4x18mm)
F
4PCS
Shelf Holder
G
2PCS
Metal Pin
H
1PC
Magnet
J
1PC
Magnet Plate
K
1PC
Screw (3x10mm)
M
2PCS
Screw (3x14mm)
N
16PCS
Screw (4x20mm)
P
2PCS
Screw (4x30mm)
Q
2PCS
Plastic Anchor
R
2PCS
Adjustable Anchor Bracket
S
2PCS
Screw (4x10mm)
TOOLS NEEDED FOR ASSEMBLY: FLAT & PHILLIPS SCREWDRIVER (NOT INCLUDED)
THE USE OF A POWER SCREWDRIVER IS NOT RECOMMENDED FOR ASSEMBLY
DO NOT USE ITEM IF ANY PARTS ARE MISSING OR DAMAGED
To order replacement parts at no cost to you, email [e-mail], call
1-(844)-223-5201 or order parts online at www.riverridgehome.com. Only valid in the United States.
If purchased outside of the United States, please contact retailer where purchased.

STEP 1
1. Insert 3 wood dowels (C) into dowel holes on top board (1).
2. Screw 6 cam bolts (A) into cam bolt holes on top board (1).
3. Insert 2 screws (S) through holes on adjustable anchor bracket (R), then tighten to top
board (1).
STEP 2
1. Insert 3 wood dowels (C) into dowel holes on bottom board (2).
2. Screw 6 cam bolts (A) into cam bolt holes on bottom board (2).

STEP 3
1. Insert 4 wood dowels (C) into dowel holes on arch shelf (3).
2. Repeat above step for another arch shelf (3).
STEP 4
1. Insert 2 wood dowels (C) into dowel holes on edge of rear support board (4).

STEP 5
1. Attach magnet (H) to center support panel (5).
2. Insert 2 screws (M) through holes on magnet (H) and tighten to center support panel (5).
STEP 6
1. Insert 1 screw (K) through hole on magnet plate (J) and tighten to door (7).
2. Attach knob (D) to door (7) by inserting 1 machine screw (E) through hole on door (7)
and tighten to knob (D).
3. Insert 2 pins (G) into holes on each end of door (7).

STEP 7
1. Overturn bottom board (2) and attach one leg (10) to bottom board (2) by inserting 4
screws (N) through holes on leg (10) and tighten to bottom board (2).
2. Repeat above step to assemble other 3 legs.
STEP 8
1. Attach arch shelves (3) to rear support board (4) by inserting wood dowels into dowel
holes on rear support board (4).

STEP 9
1. Attach center support panel (5) to rear support board (4) and arch shelves (3) by inserting
wood dowels into holes on center support panel (5).
STEP 10
1. Attach rear support board (4), center support panel (5) and right side panel (6) to bottom
board (2) by inserting cam bolts into cam lock holes and inserting wood dowels into dowel
holes on rear support board (4), center support panel (5) and right side panel (6).
2. Insert 6 cam locks (B) into cam lock holes on rear support board (4), center support panel
(5) and right side panel (6) and rotate clockwise to secure cam bolts (A).

STEP 11
1. Slide back board (9) into grooves on center support panel (5), right side panel (6) and
bottom board (2).
STEP 12
1. Attach door (7) to assembled unit by inserting pin (G) into hole on bottom board (2).

STEP 13
1. Attach top board (1) to pre-assembled cabinet by
inserting cam bolts into cam lock holes, wood
dowels into dowel holes and pin into holes on rear
support board (4), center support panel (5), right
side panel (6) and door (7).
2. Insert 6 cam locks (B) into cam lock holes on rear
support board (4), center support panel (5) and
right side panel (6) and rotate clockwise to secure
cam bolts.
STEP 14
1. Insert 4 holders (F) into hole position that you desire for shelf and place shelf (8) onto
holders (F).
Option #1: Securing to Drywall
1. Position cabinet against wall in desired location. Using a pencil, make 2 small marks on wall
through holes on brackets (R). Move cabinet away from wall and screw 2 plastic anchors (Q)
into wall on pencil marks.
2. Place cabinet against wall, insert 2 screws (P) through holes on metal brackets (R), then
tighten to plastic anchors (Q).
Option #2: Securing to Drywall and Wood Stud
1. Position cabinet against wall in desired location. Insert 2 screws (P) through holes on metal
brackets (R), then tighten through drywall and into wood stud.
*Tip: Anchor brackets (R) can be adjusted to correct distance from wall to cabinet as needed. Once
adjusted, be sure to re-tighten brackets inside cabinet for stability.

ATTENTION ADULTS: Cabinet should be checked periodically for damage or
loose screws/parts. Take appropriate action necessary to correct hazards such as
tightening of screws and taking any damaged parts away from children.
WARNING Please make sure your item is
secured to the wall, per assembly instructions.
CARE INSTRUCTIONS:
Wipe clean with a water dampened cloth. Wipe dry with clean cloth.
IMPORTANT:
Keep assembly instructions for future reference.

Enjoy your new RiverRidge® Cabinet!
Thank you for purchasing this RiverRidge® Home item. We hope you
enjoy it and consider purchasing other RiverRidge® items.
To order replacement parts at no cost to you, email [email protected], call
1-(844)-223-5201 or order parts online at www.riverridgehome.com. Only valid in the United States.
If purchased outside of the United States, please contact retailer where purchased.
RiverRidge® is a registered trademark of Sourcing Solutions, Inc., Hudson, WI 54016