RiverRidge Medford Tall Cabinet 06-106 User manual

ASSEMBLY INSTRUCTIONS
RiverRidge® Medford Tall Cabinet
ITEM #: 06-106 White
ADULT ASSEMBLY REQUIRED
This product requires assembly by an adult because of small parts. Care should be taken
in unpacking and assembling this item to keep small parts away from children. During assembly
children should be kept away from the product due to possible risk of injury.
WARNING SEE FULL WARNING ON PAGE 2
Young children can be seriously injured or killed if furniture tips over. Don’t use
this item for a TV stand or place heavy objects on top of item. Always use
angle-braces or anchors to secure furniture to the wall.

THIS SHELF UNIT WILL HOLD UP TO 25 POUNDS PER SHELF OR A TOTAL OF 100 POUNDS.
DO NOT LOAD EACH SHELF WITH MORE THAN 25 POUNDS OR 100 POUNDS TOTAL WEIGHT.
IF OVERLOADED WITH MORE THAN 25 POUNDS PER SHELF OR 100 POUNDS TOTAL
WEIGHT, SHELF MAY TIP FROM THE WALL AND CAUSE SERIOUS INJURY OR DEATH.

PARTS LIST
NO
QTY
DESCRIPTION
1
1PC
Top Board
2
1PC
Upper Left Side Panel
3
1PC
Upper Right Side Panel
4
1PC
Top Fixed Shelf
5
1PC
Middle Connection Board
6
1PC
Door
7
1PC
Adjustable Shelf
8
1PC
Bottom Board
9
1PC
Lower Left Side Panel
10
1PC
Lower Right Side Panel
11
1PC
Upper Back Board
12
1PC
Lower Back Board
13
1PC
Upper Back Board

TOOLS NEEDED FOR ASSEMBLY: FLAT & PHILLIPS SCREWDRIVER (NOT INCLUDED)
THE USE OF A POWER SCREWDRIVER IS NOT RECOMMENDED FOR ASSEMBLY
DO NOT USE ITEM IF ANY PARTS ARE MISSING OR DAMAGED
To order replacement parts at no cost to you, email [email protected], call
1-(844)-223-5201 or order parts online at www.riverridgehome.com. Only valid in the United States.
If purchased outside of the United States, please contact retailer where purchased.
NO
PARTS
QTY
DESCRIPTION
A
14PCS
Cam Bolt
B
14PCS
Cam Lock
C
4PCS
Wood Dowel
D
1PC
Magnet
E
10PCS
Screw (3x14mm)
F
1PC
Adjustable Anchor Bracket
G
1PC
Screw (3x10mm)
H
4PCS
Shelf Holder
I
4PCS
Screw (4x35mm)
J
1PC
Magnet Plate
K
2PCS
Door Pin
L
1PC
Screw (4x25mm)
M
1PC
Knob
N
1PC
Screw (4x30mm)
O
1PC
Plastic Anchor
P
8PCS
Plastic Bracket
Q
1PC
Screw (4x12mm)

STEP 1
1. Screw 4 cam bolts (A) into cam bolt holes on top board (1).
2. Attach 1 metal bracket (F) to top board (1) by inserting 1 screw (Q) through hole on metal bracket
(F) and tighten to top board (1).
3. Screw 4 cam bolts (A) into cam bolt holes on middle connection board (5).
4. Attach magnet (D) to middle connection board (5) by inserting 2 screws (E) through holes on
magnet (D) and tighten to middle connection board (5).
STEP 2
1. Screw 1 cam bolt (A) into cam bolt hole on upper left side panel (2).
2. Screw 1 cam bolt (A) into cam bolt hole on upper right side panel (3).
STEP 3
1. Screw 2 cam bolts (A) into cam bolt holes on lower left side panel (9).
2. Screw 2 cam bolts (A) into cam bolt holes on lower right side panel (10).

STEP 4
1. Attach magnet plate (J) to door (6) by inserting 1 screw (G) through hole on magnet plate (J) and
tighten to door (6).
2. Attach knob (M) to door (6) by inserting 1 screw (L) through hole on door (6) and tighten to knob
(M).
3. Insert 2 door pins (K) into holes on door (6).
STEP 5
1. Insert 2 wood dowels (C) into wood dowel holes on upper left side panel (2).
2. Attach top fixed shelf (4) to upper left side panel (2) by inserting wood dowels (C) into wood
dowel holes and inserting cam bolts (A) into cam lock holes on top fixed shelf (4).
3. Insert cam lock (B) into cam lock hole on top fixed shelf (4) and rotate clockwise to secure cam
bolt in place.
4. Repeat above steps to assemble upper right side panel (3) to top fixed shelf (4).

STEP 6
1. Slide 1 upper back board (11) into grooves on upper left side panel (2), upper right side panel
(3) and top fixed shelf (4).
2. Attach middle connection board (5) to upper left side panel (2), upper right side panel (3) and
upper back board (11) by aligning upper back board (11) with groove on middle connection
board (5).
3. Insert 4 screws (I) through holes on middle connection board (5) and tighten to upper left side
panel (2) and upper right side panel (3).
STEP 7
1. Slide upper back board (13) into grooves on upper left side panel (2), upper right side panel (3)
and top fixed shelf (4).
2. Attach top board (1) to upper left side panel (2), upper right side panel (3) and upper back board
(13) by aligning upper back board (13) with groove on top board (1) and inserting cam bolts (A)
into cam lock holes on upper left side panel (2) and upper right side panel (3).
3. Insert 4 cam locks (B) into cam lock holes and rotate clockwise to secure cam bolts in place.

STEP 8
1. Attach bottom board (8) to lower left side panel (9) by inserting cam bolts (A) into cam lock holes
on bottom board (8).
2. Insert 2 cam locks (B) into cam lock holes on bottom board (8) and rotate clockwise to secure
cam bolts in place.
3. Repeat above steps to assemble lower right side panel (10) to bottom board (8).
4. Slide lower back board (12) to grooves on lower left side panel (9), lower right side panel (10)
and bottom board (8).
STEP 9
1. Attach door (6) to bottom board (8) by inserting door pin (K) into door pin hole on bottom board
(8).
2. Attach pre-assembled upper unit to pre-assembled lower unit by inserting door pin (K) into door
pin hole on middle connection board (5) and inserting cam bolts (A) into cam lock holes on lower
left side panel (9) and lower right side panel (10).
3. Insert 4 cam locks (B) into cam lock holes on lower left side panel (9) and lower right side panel
(10), then rotate clockwise to secure cam bolts in place.

STEP 10
1. Insert 4 shelf holders (H) into holes on lower left side panel (9) and lower right side panel (10) and
make sure all 4 holders are on same level.
2. Place adjustable shelf (7) onto shelf holders (H).
STEP 11
1. Attach 8 plastic brackets (P) to back of cabinet by inserting 8 screws (E) through holes on plastic
brackets (P) and tighten to cabinet.

STEP 12
Option #1: Securing to Drywall
1. Position cabinet against wall in desired location. Using a pencil, make small mark on wall through
hole on bracket (F). Move cabinet away from wall and screw 1 plastic anchor (O) into wall on
pencil mark.
2. Place cabinet against wall, insert 1 screw (N) through hole on metal bracket (F), then tighten to
plastic anchor (O).
Option #2: Securing to Drywall and Wood Stud
1. Position cabinet against wall in desired location. Insert 1 screw (N) through hole on metal bracket
(F), then tighten through drywall and into wood stud.
*Tip: Anchor bracket (F) can be adjusted to correct distance from wall to cabinet as needed. Once adjusted, be
sure to re-tighten bracket inside cabinet for stability.
ATTENTION ADULTS: Cabinet should be checked periodically for damage or
loose screws/parts. Take appropriate action necessary to correct hazards such as
tightening of screws and taking any damaged parts away from children.
WARNING Please make sure your item is
secured to the wall, per assembly instructions.
CARE INSTRUCTIONS:
Wipe clean with a water dampened cloth. Wipe dry with clean cloth.
IMPORTANT:
Keep assembly instructions for future reference.

Enjoy your new RiverRidge® Cabinet!
Thank you for purchasing this RiverRidge® Home item. We hope you
enjoy it and consider purchasing other RiverRidge® items.
To order replacement parts at no cost to you, email [email protected], call
1-(844)-223-5201 or order parts online at www.riverridgehome.com. Only valid in the United States.
If purchased outside of the United States, please contact retailer where purchased.
RiverRidge® is a registered trademark of Sourcing Solutions, Inc., Hudson, WI 54016