RiverRidge 06-005 User manual

ASSEMBLY INSTRUCTIONS
RiverRidge® X-Frame Wall Shelf with Hooks
ITEM #: 06-005 White
ITEM #: 06-006 Espresso
ADULT ASSEMBLY REQUIRED
This product requires assembly by an adult because of small parts. Care should be taken
in unpacking and assembling this item to keep small parts away from children. During assembly
children should be kept away from the product due to possible risk of injury.
WARNING SEE FULL WARNING ON PAGE 2
Young children can be seriously injured or killed if furniture tips over. Don’t use
this item for a TV stand or place heavy objects on top of item. Always use
angle-braces or anchors to secure furniture to the wall.

THIS SHELF UNIT WILL HOLD UP TO 25 POUNDS PER SHELF OR A TOTAL OF 50 POUNDS.
DO NOT LOAD EACH SHELF WITH MORE THAN 25 POUNDS OR A TOTAL OF 50 POUNDS
TOTAL WEIGHT. IF OVERLOADED WITH MORE THAN 25 POUNDS PER SHELF OR 50
POUNDS TOTAL WEIGHT, THE SHELF MAY FALL FROM THE WALL AND CAUSE SERIOUS
INJURY OR DEATH.

PARTS LIST
NO
QTY
DESCRIPTION
1
1PC
Top Board
2
2PCS
Side Frame
3
1PC
Bottom Board
4
1PC
Back Board
5
1PC
Left Side Panel
6
1PC
Right Side Panel
7
1PC
Back Cross Bar
8
1PC
Front Cross Bar

PARTS LIST
NO
PARTS
QTY
DESCRIPTION
A
4PCS
Wood Dowel
B
8PCS
Screw (5x45mm)
C
12PCS
Screw (4x35mm)
D
6PCS
Screw (3x12mm)
E
3PCS
Hook
F
4PCS
Plastic Cap
G
2PCS
Screw (4x60mm)
H
2PCS
Plastic Anchor
I
1PC
Allen Wrench
1PC
Wall Mounting Paper Template
TOOLS NEEDED FOR ASSEMBLY: FLAT & PHILLIPS SCREWDRIVER (NOT INCLUDED)
THE USE OF A POWER SCREWDRIVER IS NOT RECOMMENDED FOR ASSEMBLY
DO NOT USE ITEM IF ANY PARTS ARE MISSING OR DAMAGED
To order replacement parts at no cost to you, email [email protected], call
1-(844)-223-5201 or order parts online at www.riverridgehome.com. Only valid in the United States.
If purchased outside of the United States, please contact retailer where purchased.

STEP 1
1. Place top board (1) upside down on soft padded surface.
2. Attach back cross bar (7) to top board (1) by inserting 3 screws (C) through holes on back
cross bar (7) and tighten to top board (1).
3. Repeat above step to attach front cross bar (8) to top board (1).
STEP 2
1. Attach 1 side frame (2) to top board (1) by inserting 2 screws (B) through holes on side
frame (2), then tighten to back cross bar (7) and front cross bar (8) using Allen wrench (I).
When tightening, slightly push screw in to catch inner thread.

STEP 3
1. Attach other side frame (2) to top board (1) by inserting 2 screws (B) through holes on
side frame (2), then tighten to back cross bar (7) and front cross bar (8) using Allen
wrench (I).
STEP 4
1. Attach bottom board (3) to bottom of side frames (2) by inserting 4 screws (B) through
holes on bottom board (3), then tighten to side frames (2) using Allen wrench (I).

STEP 5
1. Attach 3 hooks (E) to back board (4) by inserting 6 screws (D) through holes on hooks (E),
then tighten to back board (4).
2. Insert 2 wood dowels (A) into dowel holes on left side panel (5) and attach left side panel (5)
to back board (4) by inserting wood dowels (A) into dowel holes on back board (4).
3. Insert 1 screw (C) through hole on left side panel (5) and tighten to back board (4).
4. Repeat above steps 2 and 3 to assemble right side panel (6).
STEP 6
1. Attach assembled back board (4) to bottom board (3) by inserting 2 screws (C) through holes
on bottom board (3) and tighten to left side panel (5), then insert 2 screws (C) through holes on
bottom board (3) and tighten to right side panel (6).

STEP 7
1. Press 4 plastic caps (F) into screw holes on both side frames (2).
*Tip: If added pressure is needed to keep plastic caps in place – cover caps with a piece of paper and tap
lightly with hammer to secure cap.
STEP 8
Option #1: Securing to Drywall
1. Using wall mounting paper template to determine position, screw 2 plastic anchors (H) into
drywall.
2. Insert 2 screws (G) through holes on back cross bar (7) and into plastic anchors (H) and
tighten.
Option #2: Securing to Drywall and Wood Stud
1. Insert 2 screws (G) through holes on back cross bar (7), then tighten through drywall and into
wood stud.

ATTENTION ADULTS: Cabinet should be checked periodically for damage or
loose screws/parts. Take appropriate action necessary to correct hazards such as
tightening of screws and taking any damaged parts away from children.
WARNING Please make sure your item is
secured to the wall, per assembly instructions.
CARE INSTRUCTIONS:
Wipe clean with a water dampened cloth. Wipe dry with clean cloth.
IMPORTANT:
Keep assembly instructions for future reference.

Enjoy your new RiverRidge® Wall Shelf!
Thank you for purchasing this RiverRidge® Home item. We hope you
enjoy it and consider purchasing other RiverRidge® items.
To order replacement parts at no cost to you, email [email protected], call
1-(844)-223-5201 or order parts online at www.riverridgehome.com. Only valid in the United States.
If purchased outside of the United States, please contact retailer where purchased.
RiverRidge® is a registered trademark of Sourcing Solutions, Inc., Hudson, WI 54016