RiverRidge Bayfield 06-113 User manual

ASSEMBLY INSTRUCTIONS
ITEM #: 06-113 White
RiverRidge®Bayfield Single Door Floor Cabinet
ASSEMBLY INSTRUCTIONS
ADULT ASSEMBLY REQUIRED
WARNING
SEE FULL WARNING ON PAGE 2
This product requires assembly by an adult because of small parts. Care should be taken
in unpacking and assembling this item to keep small parts away from children. During assembly
children should be kept away from the product due to possible risk of injury.
Young children can be seriously injured or killed if furniture tips over.
Don’t use this item for a TV stand or place heavy objects on top of item.
Always use angle-braces or anchors to secure furniture to the wall.

THIS SHELF UNIT WILL HOLD UP TO 20 POUNDS PER SHELF OR TOP BOARD
FOR A TOTAL OF 80 POUNDS. DO NOT LOAD EACH SHELF WITH MORE
THAN 20 POUNDS OR 80 POUNDS TOTAL WEIGHT. IF OVERLOADED WITH
MORE THAN 20 POUNDS PER SHELF OR 80 POUNDS TOTAL WEIGHT, SHELF
MAY TIP FROM THE WALL AND CAUSE SERIOUS INJURY OR DEATH.

Top Board1PC
QTYNO DESCRIPTION
1
Left Side Panel1PC2
Right Side Panel1PC3
Upper Cross Bar1PC4
Adjustable Shelf1PC5
Shelf1PC6
Lower Cross Bar1PC7
Bottom Shelf1PC8
Back Board
1PC9
1PC10 Door
1
2
3
4
5
6
7
10
9
8
PARTS LIST

TOOLS NEEDED FOR ASSEMBLY: FLAT & PHILLIPS SCREWDRIVER (NOT INCLUDED)
THE USE OF A POWER SCREWDRIVER IS NOT RECOMMENDED FOR ASSEMBLY
DO NOT USE ITEM IF ANY PARTS ARE MISSING OR DAMAGED
PARTS LIST
NO QTYPARTS DESCRIPTION
A12PCS Cam Bolt
B12PCS Cam Lock
C20PCS Wood Dowel
D
1PC
E
F
Screw (2.5x10mm)
G8PCS
H
10PCS
J
4PCS
2PCS Hinge
Shelf Holder
Screw (4x30mm)
3PCS
Screw (4x12mm)
Screw (4x35mm)
Plastic Anchor1PC
K
Adjustable Anchor Bracket1PC
L
Screw (4x12mm)1PC
I
To order replacement parts at no cost to you, email [email protected], call
1-(844)-223-5201 or order parts online at www.riverridgehome.com. Only valid in the United States.
If purchased outside of the United States, please contact retailer where purchased.

STEP 1
1. Insert 4 cam bolts (A) into cam bolt holes on left side panel (2).
2. Insert 4 cam bolts (A) into cam bolt holes on right side panel (3).
1. Insert 4 cam bolts (A) into cam bolt holes on top board (1).
2. Attach bracket (L) to top board (1) by inserting 1 screw (I) through hole on bracket (L), then
tighten to top board (1).
1. Attach lower cross bar (7) to bottom shelf (8) by inserting 2 screws (F) through holes
on lower cross bar (7), then tighten to bottom shelf (8).
STEP 2
STEP 3
A
A
A
A
A
A
A
A
A
A
A
A
F
F
I
I
L
L
1
23
7
8

1. Attach 2 hinges (E) to door (10) by inserting 4 screws (G) through holes on hinges (E), then
tighten to door (10).
1. Insert 7 wood dowels (C) into wood dowel holes on left side panel (2).
2. Attach upper cross bar (4), shelf (6), bottom shelf (8) and lower cross bar (7) to left side
panel (2) by inserting wood dowels (C) into wood dowel holes and insert cam bolts (A) into cam
lock holes on upper cross bar (4), shelf (6) and bottom shelf (8).
3. Insert 4 cam locks (B) into cam lock holes on shelf (6) and bottom shelf (8), then rotate
clockwise to secure cam bolts (A) in place.
STEP 4
STEP 5
GG
E
2
46
8
7
10
B
B
B
BC
C
C
C
C
C
GG
GG
E
E

1. Insert 7 wood dowels (C) into wood dowel holes on right side panel (3).
2. Attach right side panel (3) to upper cross bar (4), shelf (6), bottom shelf (8) and lower
cross bar (7) to by inserting wood dowels (C) into wood dowel holes and insert cam bolts (A)
into cam lock holes on upper cross bar (4), shelf (6) and bottom shelf (8).
3. Insert 4 cam locks (B) into cam lock holes on shelf (6) and bottom shelf (8), then rotate
clockwise to secure cam bolts (A) in place.
1. Insert 6 wood dowels (C) into wood dowel holes on top board (1).
2. Attach top board (1) to left side panel (2), right side panel (3) and upper cross bar (4) by
inserting wood dowels (C) into wood dowel holes and insert cam bolts (A) into cam lock
holes on left side panel (2), right side panel (3) and upper cross bar (4).
3. Insert 4 cam locks (B) into cam lock holes on left side panel (2) and rightside panel (3), then
rotate clockwise to secure cam bolts (A) in place.
4. Insert 1 screw (F) into screw hole on upper cross bar (4), then tighten to top board (1).
STEP 6
STEP 7
14
2
3
B
B
B
F
B
C
C
C
C C
C
B
B
B
B
C
C
CC
C
CC
3
2
4
6
8
7

1. Attach back board (9) to back of cabinet by inserting 10 screws (J) through holes on back
board (9), then tighten to cabinet.
1. Insert 4 shelf holders (D) into desired position.
2. Place adjustable shelf (5) onto 4 shelf holders (D), making sure all shelf holders are at
same level.
STEP 8
STEP 9
D
D
D
D
D
JJ
J
J
J
J
JJ
J
J
5
9

1. Attach door (10) to cabinet by inserting 4 screws (G) through holes on hinges (E), then tighten
to right side panel (3).
2. Note: Tightening screw in position “a” will adjust door up or down; tightening screw in position
“b” will adjust door to or from cabinet, and tightening screw in position “c” will adjust door
side to side.
G
G
G×2
G×2
b
a
a
bc
c
STEP 10
10
E

STEP 11
H
K
K
H
H
DRYWALL
WALL ANCHOR
WITH SCREW
SCREW
ONLY
DRYWALL
OPTION #2OPTION #1
WOOD
STUD
Option #1: Securing to Drywall
1. Position cabinet against wall in desired location. Using a pencil, make a small mark on wall through hole
on bracket (L). Move cabinet away from wall and screw 1 plastic anchor (K) into wall on pencil mark.
2. Place cabinet against wall, insert 1 screw (H) through hole on metal bracket (L), then tighten to plastic
anchor (K).
Option #2: Securing to Drywall and Wood Stud
1. Position cabinet against wall in desired location. Insert 1 screw (H) through hole on metal bracket (L),
then tighten through drywall and into wood stud.
H
K
*Tip: Anchor bracket (L) can be adjusted to correct distance from wall to cabinet as needed. Once adjusted,
be sure to re-tighten bracket inside cabinet for stability.
ATTENTION ADULTS: Cabinet should be checked periodically for damage or
loose screws/parts. Take appropriate action necessary to correct hazards such as
tightening of screws and taking any damaged parts away from children.
WARNING Please make sure youritem is
secured to the wall, per assembly instructions.
CARE INSTRUCTIONS:
Wipe clean with a water dampened cloth. Wipe dry with clean cloth.
IMPORTANT:
Keep assembly instructions for future reference.

Enjoy your new RiverRidge®Cabinet!
To order replacement parts at no cost to you,email [email protected], call
1-(844)-223-5201 or order parts online at www.riverridgehome.com. Only valid in the United States.
If purchased outside of the United States, please contact retailer where purchased.
RiverRidge® is a registered trademark of Sourcing Solutions, Inc., Hudson, WI 54016
Thank you for purchasing this RiverRidge®Home item. We hope you
enjoy it and consider purchasing other RiverRidge®items.