RiverRidge 06-035 User manual

ASSEMBLY INSTRUCTIONS

RiverRidge® LADDER SHELF
ITEM#:06-035 White
ITEM#:06-036 Espresso
ADULT ASSEMBLY REQUIRED
This product requires assembly by an adult because of the small parts. Care should be
taken in unpacking and assembling this item to keep the small parts away from children.
WARNING
Young children can be seriously injured or killed, if furniture tips over.
Don’t use this item for a TV stand.
Use angle-braces or anchors to secure furniture to the wall.

Send requests for missing or damaged parts replacements by email to :
[email protected] or call toll free 1-(844)-223-5201 or order parts on line at
www.riverridgehome.com
THIS SHELF UNIT WILL HOLD UP TO 12 POUNDS PER SHELF OR A TOTAL OF 36 POUNDS. DO
NOT LOAD EACH SHELF WITH MORE THAN 12 POUNDS. IF LOADED WITH MORE THAN 12
POUNDS PER SHELF AS THIS MAY CAUSE DAMAGE TO THE SHELF AND MAY CAUSE SERIOUS
INJURY OR DEATH.

PARTS LIST
TOOLS NEEDED FOR ASSEMBLY: FLAT & PHILIPS SCREWDRIVER (NOT INCLUDED)
THE USE OF POWER SCREWDRIVER IS NOT RECOMMENDED
1
1PC TOP SHELF
2
1PC SECOND SHELF
3
1PC THIRD SHELF
4 1PC LEFT UPPER SIDE PANEL
5 1PC LEFT LOWER SIDE PANEL
6 1PC RIGHT UPPER SIDE PANEL
7 1PC RIGHT LOWER SIDE PANEL
8 2PCS CROSS BAR
A 4PCS METAL CONNECTION BAR
B
12PCS SCREW 6x20mm
C 4PCS LONG SCREW 4x35mm
D 8PCS SHORT SCREW 4x12mm
E
2PCS ANCHOR SCREW 4x40mm
F
2PCS PLASTIC ANCHOR

STEP 1
STEP-1:
1. Insert 2 Metal Connection Bars (A) into the holes on the end of Left Upper Side Panel (4), make sure the hole on
the Metal Connection Bar (A) is towards the hole on the Left Upper Side Panel (4).
2. Insert 2 screws (D) through the holes on the Left Upper Side Panel (4) and tighten to Metal Connection Bar (A).
3. Attach Left Lower Side Panel (5) to Left Upper Side Panel (4) by inserting the Metal Connection Bar (A) into the
holes on end of Left Lower Side Panel (5), make sure the hole on the Metal Connection Bar (A) is towards the
hole on the Left Lower Side Panel (5).
4. Insert 2 screws (D) through the holes on the Left Lower Side Panel (5) and tighten to Metal Connection Bar (A).
5. Repeat above steps to connect the Right Upper Side Panel (6) and Right Lower Side Panel (7).
STEP 2
STEP-2:
1. Attach 2 Cross Bars (8) to pre-assembled left side panel (4,5) by inserting 2 Long Screws (C) through the holes
on the Left Side Panel then tighten to Cross Bar (8).
2. Attach Top Shelf (1) to Left Side Panel by inserting 2 Screws (B) through the holes on the Top Shelf (1) then
tighten to the Left Side Panel.
3. Repeat Step #2 to attach Second Shelf (2) and Third Shelf (3).

STEP 3
STEP-3:
1. Attach 2 Cross Bars (8) to pre-assembled right side panel (6,7) by inserting 2 Long Screws (C) through the holes
on the Right Side Panel then tighten to Cross Bar (8).
2. Attach Top Shelf (1) to Right Side Panel by inserting 2 screws (B) through the holes on the Top Shelf (1) then
tighten to the Right Side Panel.
3. Repeat Step #2 to attach Second Shelf (2) and Third Shelf (3).
STEP 4
STEP-4:
1. Drill 2 holes on the wall using the holes in the Top Shelf (1) as a guide.
2. Insert 2 Plastic Anchors (F) into the holes on the wall.
3. Insert 2 Anchor Screws (E) through the holes on the Top Shelf (1) then tighten to the 2 Plastic Anchors (F).