Vivo DESK-V100EBY User manual

Black Electric Single Motor Desk Frame
Follow along step-by-step with our video walk through by scanning
the QR code with your mobile device or by following the product
link: vivo-us.com/products/desk-v100eby
Instruction Manual
SKU: DESK-V100EBY
ASSEMBLY VIDEO AVAILABLE:
[email protected]om www.vivo-us.com 309-278-5303

Contact Us First!
PERSONABLE CUSTOMER SUPPORT
Our friendly product support team is here to help!
DO NOT RETURN ITEM
We’re Here for You!
Missing a Part?
Our customer-minded support team is here for YOU,
Monday-Friday 7am-7pm CST.
We oer immediate assistance with rapid response times
from customer service agents and product techncians to
help you every step of the way!
Monday-Friday
Chat Us:
www.vivo-us.com
Give us a Call:
309-278-5303
Email Us:
[email protected]om
If any parts are received damaged / defective OR you are
missing a part, please reach out to us within 30 days of
product delievery to have it replaced at no cost.
We are happy to replace parts to ensure you have a fully
functioning product
7AM - 7PM

If you do not understand these directions, or if you have any
doubts about the safety of the installation, please call a qualified
technician. Check carefully to make sure there are no missing
or defective parts. Improper installation may cause damage or
serious injury. Do not use this product for any purpose that is
not explicitly specified in this manual. Do not exceed weight capacity. We
cannot be liable for damage or injury caused by improper mounting, incorrect
assembly or inappropriate use.
PRE-ASSEMBLY | BEFORE YOU BEGIN
Product Warranty
Returns | Product Didn’t Work Out?
For the most up to date details on your product’s warranty, please visit
the product’s listing on our website or reach out to customer support.
vivo-us.com/products/desk-v100eby
We oer a hassle-free 30 day return on all products. Contact customer
support at 309-278-5303 or [email protected]om. Please note: For items
ordered in error or no longer needed, the return shipping charges will
be at the buyer’s expense.
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS
REQUIRED.
WEIGHT CAPACITY
DO NOT EXCEED WEIGHT CAPACITY. Failure to do so may result in serious injury.
176lbs
(80kg)
!
THIS PRODUCT IS POWERED BY ELECTRICITY. IN ORDER TO AVOID BURNS, FIRE AND ELECTRIC
SHOCK, PLEASE READ THE FOLLOWING INSTRUCTIONS CAREFULLY.
• DO NOT CLEAN PRODUCT WHILE POWER IS CONNECTED.
• DO NOT DISASSEMBLE OR REPLACE COMPONENTS WHILE POWER IS CONNECTED.
• NEVER OPERATE THE SYSTEM WITH A DAMAGED CORD OR PLUG. PLEASE CONTACT YOUR
SELLER TO REPLACE DAMAGED PARTS.
• NEVER OPERATE SYSTEM IN DAMP ENVIRONMENTS OR IF ANY ELECTRICAL COMPONENTS HAVE
MADE CONTACT WITH LIQUIDS.
• ALTERATIONS OF THE GIVEN POWER UNIT ARE NOT ALLOWED.
• OUTDOOR USE IS PROHIBITED.
ELECTRICAL WARNING :

4
PACKAGE CONTENTS
A (x1)
Leg
B(x1)
Motorized
Leg
C(x2)
Foot
D (x2)
Side Bracket
S-A (x4)
M8x50mm Screw
S-B (x8)
M6x35mm Screw
S-C (x4)
M8x16mm Screw
Please consult the parts list below and ensure you have everything you need to assemble
your product. If parts are missing or damaged, please contact us.
Phillips Screwdriver
|
TOOLS NEEDED:
DIFFICULTY LEVEL
E (x1)
Sync Rod
F (x1)
Crossbar G(x1)
Controller
H (x1)
Power Cord
I (x2)
Hook
J(x5)
Cable Clip
S-D (x12)
ST4.2x15mm Screw
T-A (x1)
5mm Allen
Wrench
T-B (x1)
Wrench
Drill

5
A
Leg
B
Motorized Leg
S-A
M8x50mm Screw
STEP 1: Mount Crossbar
ASSEMBLY STEPS
F
Crossbar
T-A
5mm Allen Wrench
Loosen screws on Crossbar (F) using 5mm Allen Wrench (T-A), extend, and then re-tighten
screws. Mount Crossbar (F) to Leg (A) and Motorized Leg (B) using M8x50mm Screws (S-A) and
5mm Allen Wrench (T-A).
M-E
M-E
F
B
M-A
A
S-A
B
A
F
T-A
T-A

6
STEP 2: Install Feet
Assemble Foot (E) to Leg (B) and Motorized Leg (C) using M6x35mm Screws (S-B) and 5mm Allen Wrench
(T-A).
M-E
M-B
T-A
S-B
C
B
A
C
Foot
A
Leg
B
Motorized Leg
S-B
M6x35mm Screw
T-A
5mm Allen Wrench

7
STEP 3: Attach Side Brackets
Install Side Brackets (D) on Leg (A) and Motorized Leg (B) using M8x16mm Screw (S-C) and 5mm
Allen Wrench (T-A).
D
M-E
M-C
S-C
T-A
B
C
D
Side Bracket
S-C
M8x16mm Screw
T-A
5mm Allen Wrench

8
STEP 4: Adjust Desk Frame Width
Use 5mm Allen Wrench (T-A) to losen set screws on Crossbar (F) and adjust to fit width of
desktop. Re-tighten to secure.
M-E
F
T-A
T-A
5mm Allen Wrench

9
STEP 5: Attach Frame to Desktop
Secure frame assembly to the desktop with ST4.2x15mm Screws (S-D) and a Phillips screwdriver.
M-D
S-D
S-D
ST4.2x15mm Screw

10
STEP 6: Install Sync Rod
Loosen the knobs on the Sync Rod (E) and extend the hex sha. Insert hex sha into the Leg (A),
making sure the metal retaining ring makes contact with the Leg. While holding the hex sha
with one hand, extend Sync Rod onto the spline sha of Motorized Leg (B). Retighten knob with
Wrench (T-B).
12-1 2-2 3
1
2
3
E
T-B
E
Sync Rod
T-B
Wrench