RiverRidge Madison 06-111 User manual

ASSEMBLY INSTRUCTIONS
RiverRidge®Madison Single Door Floor Cabinet
ITEM #: 06-111 White
ADULT ASSEMBLY REQUIRED
This product requires assembly by an adult because of small parts. Care should be taken in
unpacking and assembling this item to keep small parts away from children.
WARNING SEE FULL WARNING ON PAGE 2
Young children can be seriously injured or killed if furniture tips over. Don’t use
this item for a TV stand or place heavy objects on top of item. Always use
angle-braces or anchors to secure furniture to the wall.

THIS SHELF UNIT WILL HOLD UP TO 20 POUNDS PER SHELF OR TOP BOARD FOR
A TOTAL OF 80 POUNDS. DO NOT LOAD EACH SHELF WITH MORE THAN 20
POUNDS OR 80 POUNDS TOTAL WEIGHT. IF OVERLOADED WITH MORE THAN 20
POUNDS PER SHELF OR 80 POUNDS TOTAL WEIGHT, SHELF MAY TIP FROM THE
WALL AND CAUSE SERIOUS INJURY OR DEATH.

PARTS LIST
NO
QTY
DESCRIPTION
1
1PC
Top Board
2
1PC
Bottom Board
3
1PC
Left Side Panel
4
1PC
Right Side Panel
5
1PC
Cross Bar
6
1PC
Shelf
7
1PC
Adjustable Shelf
8
1PC
Door
9
1PC
Back Board

PARTS LIST
NO
PARTS
QTY
DESCRIPTION
A
12PCS
Cam Bolt
B
12PCS
Cam Lock
C
12PCS
Wood Dowel (6 x 30mm)
D
4PCS
Metal Shelf Holder
E
2PCS
Hinge
F
1PCS
Handle
G
14PCS
Screw (4 x 12mm)
H
1PC
Screw (4 x 10mm)
I
1PC
Bracket
J
12PCS
Screw (2.5 x 10mm)
K
1PC
Plastic Anchor
L
1PC
Screw (5 x 40mm)
M
1PC
Silicon pad
TOOLS NEEDED FOR ASSEMBLY: FLAT & PHILLIPS SCREWDRIVER (NOT INCLUDED)
THE USE OF POWER SCREWDRIVER IS NOT RECOMMENDED FOR ASSEMBLY
TOOL NEEDED FOR SECURING TO WALL: POWER DRILL (NOT INCLUDED)
To order replacement parts at no cost to you, email [e-mail],
call 1-(844)-223-5201 or order parts online at www.riverridgehome.com

STEP 1
1. Screw 4 cam bolts (A) into pre-threaded holes on top board (1).
2. Attach bracket (I) to shelf (6) by inserting 1 screw (H) through hole on bracket (I), then
tighten to shelf (6).
STEP 2
1. Screw 4 cam bolts (A) into pre-threaded holes on left side panel (3).
2. Screw 4 cam bolts (A) into pre-threaded holes on right side panel (4).
STEP 3
1. Insert 6 wood dowels (C) into wood dowel holes on left side panel (3).
2. Attach left side panel (3) to cross bar (5), shelf (6) and bottom board (2) by inserting wood dowels
(C) into wood dowel holes on cross bar (5) and inserting cam bolts (A) into cam lock holes on
shelf (6) and bottom board (2).
3. Insert 4 cam locks (B) into cam lock holes on shelf (6) and bottom board (2) then rotate
clockwise to secure cam bolts in place.
4. Repeat above steps to assemble right side panel (4) to cross bar (5), shelf (6) and bottom board (2).

STEP 4
1. Attach top board (1) to left side panel (3) and right side panel (4) by inserting cam bolts into
cam lock holes on left side panel (3) and right side panel (4).
2. Insert 4 cam locks (B) into cam lock holes on left side panel (3) and right side panel (4), then
rotate clockwise to secure cam bolts in place.
STEP 5
1. Attach back board (9) to cabinet by inserting 12 screws (J) through holes on back board (9),
then tighten to cabinet.

STEP 6
1. Attach 2 hinges (E) to door (8) by inserting 4 screws (G) through holes on hinges, then tighten to
door (8).
2. Attach handle (F) to door (8) by inserting 2 screws (G) through holes on handle (F), then tighten
to door (8).
3. Stick 1 silicon pad (M) on handle (F) to prevent scratches on shelf edge when door is closed.
STEP 7
1. Attach door (8) to cabinet by inserting 8 screws (G) through holes on hinges, then tighten to right
side panel (4).
2. Note: Tightening screw in position “a” will adjust door up or down; tightening screw in position “b”
will adjust door to or from cabinet and tightening screw in position “c” will adjust door side to side.
Door Adjustments

STEP 8
1. Place drawing with hole position on wall in desired location and drill hole on wall.
2. Insert plastic anchor (K) into hole on wall.
3. Align hole on cabinet with hole on wall, then insert screw (L) through hole on bracket (I) and
tighten to plastic anchor (K) in wall.
STEP 9
1. Insert 4 metal holders (D) into desired shelf position.
2. Place adjustable shelf (7) onto metal holders (D).

ATTENTION ADULTS: Cabinet should be checked periodically for damage or loose
screws/parts. Take appropriate action necessary to correct hazards such as tightening
of screws and taking any damaged parts away from children.
WARNING Please make sure your item is
secured to the wall, per assembly instructions.

Enjoy your new RiverRidge® Cabinet!
Thank you for purchasing this RiverRidge® Home item. We hope you
enjoy it and consider purchasing other RiverRidge® items.
To order replacement parts at no cost to you, email [e-mail],
call 1-(844)-223-5201 or order parts online at www.riverridgehome.com
RiverRidge® is a registered trademark of Sourcing Solutions, Inc., Hudson, WI 54016