RiverRidge Ellsworth Tall Corner Cabinet 06-027 User manual

ASSEMBLY INSTRUCTIONS
RiverRidge® ELLSWORTH TALL CORNER CABINET
ITEM # 06-027 WHITE
ITEM # 06-028 ESPRESSO
ADULT ASSEMBLY REQUIRED
This product requires assembly by an adult because of small parts. Care should be
taken in unpacking and assembling this item to keep small parts away from children.
WARNING SEE FULL WARNING ON PAGE 2
Young children can be seriously injured or killed if furniture tips over.
Don’t use this item for a TV stand or place heavy objects on top of item.
Always use angle-braces or anchors to secure furniture to the wall.

Send requests for missing or damaged parts replacements by email to:
customer.serv[email protected] or call toll free 1-(844)-223-5201 or order parts on lineat
www.riverridgehome.com
THIS SHELF UNIT WILL HOLD UP TO 25 POUNDS PER SHELF OR A TOTAL OF 75 POUNDS.
DO NOT LOAD EACH SHELF WITH MORE THAN 25 POUNDS OR 75 POUNDS TOTAL WEIGHT.
OVERLOADING MAY CAUSE DAMAGE TO THE SHELF AND MAYCAUSE SERIOUS INJURY
ORDEATH.

PARTS LIST
NO PARTS
QTY
DESCRIPTION
A
4PC CAM BOLT
B
4PC CAM LOCK
C
24PC WOOD DOWEL
D
1PC MAGNET
E
2PC SCREW 3x14mm
F
18PC WOOD SCREW 3x10mm
G
4PC HINGE
H
2PC MAGNET PLATE
I
30PC WOOD SCREW 4x25mm
J
2PC KNOB
K
2PC MACHINE SCREW 4x18mm
L
4PC ADJUSTABLE SHELF HOLDER
M
4PC LONG WOOD SCREW 4x35mm
N
2PC LONG WOOD DOWEL
O 4PC PLASTIC ANCHOR
P
4PC LONG SCREW 4x40mm

NO PARTS
QTY
DESCRIPTION
1 1PC MIDDLE CONNECTION BOARD
2
1PC LEFT LOWER SUPPORTBOARD
3
1PC RIGHT LOWER SUPPORT BOARD
4
1PC
LOWER CROSS BAR
5
1PC
RIGHT SIDE DOOR
6
1PC LEFT SIDE DOOR
7
1PC ADJUSTABLE SHELF
8
2PC TOP & BOTTOM FIXED SHELF
9
1PC LEFT LOWER SIDE PANEL
10
1PC RIGHT LOWER SIDE PANEL
11
1PC RIGHT UPPER SUPPORT BOARD
12
1PC LEFT UPPER SUPPORT BOARD
13
1PC TOP CROSS BOARD
14
1PC LEFT UPPER SIDE PANEL
15
1PC RIGHT UPPER SIDE PANEL
16
2PC
TOP OPEN SHELF
TOOLS NEEDED FOR ASSEMBLY: FLAT & PHILLIPS SCREWDRIVER (NOTINCLUDED)
THE USE OF POWER SCREWDRIVER IS NOT RECOMMENDED

STEP 1
1. Insert 1 wood screw (F) through hole in magnet plate (H) and tighten to right side door (5).
2. Insert 4 wood screws (F) through holes in 2 hinges (G) and tighten to right side door (5).
3. Repeat above steps to assemble magnet plate (H) and 2 hinges (G) to left side door (6).
STEP 2
1. Insert 4 wood dowels (C) into wood dowel holes on each end of lower cross bar (4).
2. Attach left lower support board (2) to lower cross bar (4) by inserting wood dowels into wood dowel holes on
left lower support board (2).
3. Attach right lower support board (3) to lower cross bar (4) by inserting wood dowels into wood dowel holes on
right lower support board (3).

STEP 3
1. Attach right side door (5) and left side door (6) to left lower support board (2) and right lower support board
(3) by inserting 8 wood screws (F) through holes in hinges (G) on right side door (5) and left side door (6) and
tighten to left lower support board (2) and right lower support board (3).
STEP 4
1. Attach shelf (8) to both lower side support boards (2), (3) by inserting 2 wood screws (I) through holes in
shelf (8) and tighten to left lower support board (2) and right lower support board (3).
2. Insert 2 wood dowels (C) into dowel holes on shelf (8).

STEP 5
1. Attach left lower side panel (9) to left lower support board (2) and shelf (8) by inserting wooden dowel (C) into
dowel hole in left lower side panel (9).
2. Insert 4 wood screws (I) through holes in left lower side panel (9) and tighten to shelf (8) and left lower
support board (2).
STEP 6
1. Attach right lower side panel (10) to shelf (8), right lower support board (3) and left lower side panel (9) by
inserting 7 screws (I) through holes in right lower side panel (10) and tighten to shelf (8), right lower side
support board (3) and left lower side panel (9).

STEP 7
1. Screw 4 cam bolts (A) into pre-threaded holes on middle connection board (1). Do not over tighten.
2. Attach magnet (D) to middle connection board (1) by inserting 2 screws (E) through holes on magnet (D) and
tighten to middle connection board (1).
STEP 8
1. Insert 4 wood dowels (C) into wood dowel holes in end of top cross board (13).
2. Attach right upper support board (11) and left upper support board (12) to top cross board (13) by inserting
wood dowels into wood dowel holes on right upper support board (11) and left upper support board (12).

STEP 9
1. Attach shelf (8) to both upper support boards (11) and (12) by inserting 2 screws (I) through holes in shelf (8)
and tighten to left upper support board (12) and right upper support board (11).
2. Insert 2 wood dowels (C) into dowel holes on shelf (8).
STEP 10
1. Insert 2 wood dowels (C) into wood dowel hole on each shelf (16).
2. Attach 2 shelf (16) to left upper side panel (14) by inserting 2 wood dowels (C) into wood dowel holes on left
upper side panel (14) and inserting 2 wood screws (I) through holes on left upper side panel (14) and tighten
to shelf (16).

STEP 11
1. Attach left upper side panel (14) to shelves (16) and left upper support board (12) and shelf (8) by inserting
wood dowels (C) into wood dowel holes on inner side of left upper side panel (14).
2. Insert 4 wood screws (I) through holes on left upper side panel (14) and tighten to shelf (8) and left upper
support board (12).
STEP 12
1. Insert 2 wood dowels (C) into wood dowel holes on shelves (16).

STEP 13
1. Attach right upper side panel (15) to left upper side panel (14), shelves (16) and shelf (8) by inserting wood
dowels (C) on shelves (16) and shelf (8) into wood dowel holes on inner side of right upper side panel (15).
2. Insert 9 wood screws (I) through holes on right upper side panel (15) and tighten to shelf (8), shelves (16),
right upper support board (11) and left upper side panel (14).
STEP 14
1. Insert 4 wood dowels (C) into wood dowel holes on end of left upper side panel (14) and right upper side
panel (15).
2. Attach middle connection board (1) by inserting wooden dowels (C) into wood dowel holes on middle
connection board (1) and insert 4 long wood screws (M) through holes on middle connection board (1) and
tighten to left upper side panel (14) and right upper side panel (15).

STEP 15
1. Insert 2 long wood dowels (N) and 4 wood dowels (C) into wood dowel holes on lower support boards (2) and
(3) and lower side panels (9) and (10).
2. Two people may be required for this step. Attach upper unit to lower unit by inserting wooden dowels (C) and
(N) into wood dowel holes on upper support boards (11) and (12) and upper side panels (14) and (15) and
inserting 4 cam bolts (A) into cam lock holes on lower side panels (14) and (15).

STEP 16
1. Insert 4 cam locks (B) into cam lock holes on left lower side panel (9) and right lower side panel (10) and
rotate cam locks (B) clockwise to lock cam bolts.
2. Insert 4 adjustable shelf holders (L) into holes on left lower side panel (9) and right lower side panel (10).
3. Insert 1 machine screw (K) through hole on left side door (6) and tighten to knob (J).
4. Repeat above step 3 to assemble knob to right door (5).

STEP 17
1. With a nail or screw mark 4 holes on wall that will be used to attach plastic wall anchors (O) and anchor
screws (P).
2. Drill holes on wall at 4 marked spots and insert 4 plastic wall anchors (O) into holes on wall.
3. Insert 4 long screws (P) through holes on lower and upper side panels and tighten to plastic wall anchor (O).
4. Place shelf (7) onto plastic holders (L).

ENJOY YOUR NEW RiverRidge® CABINET NOW!
Attention Adults: Cabinet should be checked periodically for damage or loose screws/parts.
Take appropriate action necessary to correct hazards such as tightening of screws and taking
any damaged parts away from children.
Warning Please make sure your item is secured to the wall, per
assembly instructions.
Thank you for purchasing this RiverRidge® Kids Products item. We hope you enjoy it and
consider purchasing other RiverRidge® items.
Send requests for missing or damaged parts replacements by email to:
customer.servic[email protected] or call toll free 1-(844)-223-5201 or order parts on line at
www.riverridgehome.com
RiverRidge® is a registered trademark of Sourcing Solutions, Inc., Hudson, WI54016.

INSTRUCCIONES DE ENSAMBLAJE
GABINETE ESQUINERO ALTO ELLSWORTH RiverRidge®
ARTÍCULO N.°06-027 BLANCO
ARTÍCULO N.°06-028 CAFÉESPRESSO
REQUIERE QUE UN ADULTO REALICE EL ENSAMBLAJE
Este producto requiere que un adulto lleve a cabo el ensamblaje debido a las piezas
pequeñas. Debe tener cuidado al desempacar y ensamblar este artículo para mantener las
piezas pequeñas alejadas de los niños.
ADVERTENCIA VEA LA ADVERTENCIA COMPLETA
EN LA PÁGINA 2
Los niños pequeños pueden resultar gravemente heridos o muertos si el mueble
vuelca. No utilice este artículo como soporte para el televisor ni coloque
objetos pesado sobre él.
Siempre utilice abrazaderas de ángulo o anclajes para fijar el mueble a la pared.

Envíe las solicitudes de reemplazos de piezas faltantes o dañadas por correo electrónico a:
[e-mail] o llame sin costo al 1-(844)-223-5201, o bien pida las piezas
en línea en www.riverridgehome.com
ESTA UNIDAD DE REPISAS PUEDE GUARDAR HASTA 25 LIBRAS POR REPISA O UN TOTAL
DE 75 LIBRAS. NO CARGUE CADA REPISA CON MÁS DE 25 LIBRAS O 75 LIBRAS DE PESO
TOTAL. SOBRECARGAR PUEDE DAÑAR EL GABINETE Y PUEDE OCASIONAR LESIONES
GRAVES O INCLUSO LA MUERTE.

LISTA DE PIEZAS
N.°PIEZAS CANT. DESCRIPCIÓN
A 4 PIEZAS PERNO DE ANCLAJE
B 4 PIEZAS PESTILLO DE LEVA
C 24 PIEZAS PASADOR DE MADERA
D 1 PIEZA IMÁN
E 2 PIEZAS TORNILLO 3 x 14 mm
F 18 PIEZAS
TORNILLO PARA MADERA
3 x 10 mm
G 4 PIEZAS BISAGRA
H 2 PIEZAS PLACA DE IMÁN
I 30 PIEZAS
TORNILLO PARA MADERA
4 x 25 mm
J 2 PIEZAS PERILLA
K 2 PIEZAS
TORNILLO PARA METALES
4 x 18 mm
L 4 PIEZAS SUJETADOR DE REPISA
AJUSTABLE
M 4 PIEZAS TORNILLO PARA MADERA
LARGO 4 x 35 mm
N 2 PIEZAS PASADOR DE MADERA LARGO
O 4 PIEZAS ANCLAJE PLÁSTICO
P 4 PIEZAS
TORNILLO LARGO
4 x 40 mm

N.°PIEZAS CANT. DESCRIPCIÓN
1 1 PIEZA TABLERO DE CONEXIÓN MEDIA
2 1 PIEZA
TABLERO DE SOPORTE
INFERIOR IZQUIERDO
3 1 PIEZA
TABLERO DE SOPORTE
INFERIOR DERECHO
4 1 PIEZA BARRA TRANSVERSAL INFERIOR
5 1 PIEZA PUERTA DERECHA
6 1 PIEZA PUERTA IZQUIERDA
7 1 PIEZA REPISA AJUSTABLE
8 2 PIEZAS
REPISA FIJA INFERIOR Y
SUPERIOR
9 1 PIEZA PANEL INFERIOR IZQUIERDO
10 1 PIEZA PANEL INFERIOR DERECHO
11 1 PIEZA TABLERO DE SOPORTE
SUPERIOR DERECHO
12 1 PIEZA
TABLERO DE SOPORTE
SUPERIOR IZQUIERDO
13
1 PIEZA TABLERO TRANSVERSAL
SUPERIOR
14 1 PIEZA PANEL SUPERIOR IZQUIERDO
15 1 PIEZA PANEL SUPERIOR DERECHO
16 2 PIEZAS REPISA ABIERTA SUPERIOR
HERRAMIENTAS NECESARIAS PARA EL ENSAMBLAJE: DESTORNILLADOR PLANO Y
PHILLIPS (NO INCLUIDO) NO SE RECOMIENDA EL USO DE UN DESTORNILLADOR ELÉCTRICO

PASO 1
1. Inserte 1 tornillo de madera (F) a través del agujero de la placa de imán (H) y apriete a la puerta derecha (5).
2. Inserte 4 tornillos de madera (F) a través de los agujeros de las 2 bisagras (G) y apriete a la puerta derecha (5).
3. Repita los pasos anteriores para ensamblar la placa de imán (H) y 2 bisagras (G) a la puerta izquierda (6).
PASO 2
1. Inserte 4 pasadores de madera (C) en los agujeros para los pasadores de madera en cada extremo de la barra
transversal inferior (4).
2. Fije el tablero de soporte inferior izquierdo (2) a la barra transversal inferior (4) al insertar los pasadores de
madera en los agujeros para los pasadores de madera en el tablero de soporte inferior izquierdo (2).
3. Fije el tablero de soporte inferior derecho (3) a la barra transversal inferior (4) al insertar los pasadores de
madera en los agujeros para los pasadores de madera en el tablero de soporte inferior derecho (3).