RiverRidge ELLSWORTH 06-029 User manual

ASSEMBLY INSTRUCTIONS
RiverRidge® Ellsworth Single Door Floor Cabinet
ITEM #: 06-029 White
ITEM #: 06-030 Espresso
ADULT ASSEMBLY REQUIRED
This product requires assembly by an adult because of small parts. Care should be taken
in unpacking and assembling this item to keep small parts away from children. During assembly
children should be kept away from the product due to possible risk of injury.
WARNING SEE FULL WARNING ON PAGE 2
Young children can be seriously injured or killed if furniture tips over. Don’t use
this item for a TV stand or place heavy objects on top of item. Always use
angle-braces or anchors to secure furniture to the wall.

THIS SHELF UNIT WILL HOLD UP TO 25 POUNDS PER SHELF OR A TOTAL OF 75
POUNDS. DO NOT LOAD EACH SHELF WITH MORE THAN 25 POUNDS OR 75 POUNDS
TOTAL WEIGHT. OVERLOADING MAY CAUSE DAMAGE TO THE SHELF AND MAY CAUSE
SERIOUS INJURY OR DEATH.

PARTS LIST
NO
QTY
DESCRIPTION
1
1PC
Top Board
2
1PC
Left Side Panel
3
1PC
Right Side Panel
4
1PC
Cross Bar
5
1PC
Door
6
1PC
Middle Panel
7
1PC
Bottom Board
8
1PC
Shelf
9
1PC
Back Board

PARTS LIST
NO
PARTS
QTY
DESCRIPTION
A
12PCS
Cam Bolt
B
12PCS
Cam Lock
C
17PCS
Wood Dowel
D
1PC
Knob
E
1PC
Machine Screw (4x18mm)
F
4PCS
Shelf Holder
G
2PCS
Metal Pin
H
1PC
Magnet
J
1PC
Magnet Plate
K
1PC
Screw (3x10mm)
M
2PCS
Screw (3x14mm)
N
1PC
Screw (4x30mm)
P
1PC
Plastic Anchor
Q
1PC
Adjustable Anchor Bracket
R
1PC
Screw (4x10mm)
TOOLS NEEDED FOR ASSEMBLY: FLAT & PHILLIPS SCREWDRIVER (NOT INCLUDED)
THE USE OF A POWER SCREWDRIVER IS NOT RECOMMENDED FOR ASSEMBLY
DO NOT USE ITEM IF ANY PARTS ARE MISSING OR DAMAGED
To order replacement parts at no cost to you, email [e-mail], call
1-(844)-223-5201 or order parts online at www.riverridgehome.com. Only valid in the United States.
If purchased outside of the United States, please contact retailer where purchased.

STEP 1
1. Screw 4 cam bolts (A) into cam bolt holes on top board (1).
2. Insert 5 wood dowels (C) into dowel holes on top board (1).
STEP 2
1. Screw 4 cam bolts (A) into cam bolt holes on left side panel (2).
2. Insert 6 wood dowels (C) into dowel holes on left side panel (2).
3. Attach magnet (H) to left side panel (2) by inserting 2 screws (M) through holes on magnet
(H) and tighten to left side panel (2).

STEP 3
1. Screw 4 cam bolts (A) into cam bolt holes on right side panel (3).
2. Insert 6 wood dowels (C) into dowel holes on right side panel (3).
STEP 4
1. Insert 1 screw (K) through hole on magnet plate (J) and tighten to door (5).
2. Attach knob (D) to door (5) by inserting 1 screw (E) through hole on door (5) and tighten to
knob (D).
3. Insert 2 door pins (G) into holes on each end of door (5).

STEP 5
1. Attach cross bar (4), middle panel (6) and bottom board (7) to left side panel (2) by
inserting cam bolts into cam lock holes and inserting wood dowels into dowel holes on
cross bar (4), middle panel (6) and bottom board (7).
2. Insert 4 cam locks (B) into cam lock holes on middle panel (6) and bottom board (7) and
rotate clockwise to secure cam bolts.
STEP 6
1. Slide back board (9) into grooves on left side panel (2), middle panel (6) and bottom
board (7).

STEP 7
1. Attach door (5) to middle panel (6) and bottom board (7) by inserting door pins (G) into
holes on middle panel (6) and bottom board (7).
STEP 8
1. Attach right side panel (3) to cross bar (4), middle panel (6) and bottom board (7) by
inserting cam bolts into cam lock holes and inserting wood dowels into dowel holes on
cross bar (4), middle panel (6) and bottom board (7).
2. Insert 4 cam locks (B) into cam lock holes on middle panel (6) and bottom board (7) and
rotate clockwise to secure cam bolts.

STEP 9
1. Attach top board (1) to both side panels (2), (3) and cross bar (4) by inserting cam bolts
into cam lock holes and inserting wood dowels into dowel holes on both side panels (2),
(3) and cross bar (4).
2. Insert 4 cam locks (B) into cam lock holes on both side panels (2), (3) and rotate clockwise
to secure cam bolts.
STEP 10
1. Insert 1 screw (R) through hole on adjustable anchor bracket (Q), then tighten to middle
panel (6).

STEP 11
1. Insert 4 shelf holders (F) into desired positions and put shelf (8) onto shelf holders (F).
Option #1: Securing to Drywall
1. Position cabinet against wall in desired location. Using a pencil, make small mark on wall
through hole on bracket (Q). Move cabinet away from wall and screw 1 plastic anchor (P) into
wall on pencil mark.
2. Place cabinet against wall, insert 1 screw (N) through hole on bracket (Q), then tighten to
plastic anchor (P).
Option #2: Securing to Drywall and Wood Stud
1. Place cabinet against wall in desired location. Insert 1 screw (N) through hole on bracket (Q),
then tighten through drywall and into wood stud.
*Tip: Anchor bracket (Q) can be adjusted to correct distance from wall to cabinet as needed. Once
adjusted, be sure to re-tighten bracket inside cabinet for stability.
ATTENTION ADULTS: Cabinet should be checked periodically for damage or
loose screws/parts. Take appropriate action necessary to correct hazards such as
tightening of screws and taking any damaged parts away from children.
WARNING Please make sure your item is
secured to the wall, per assembly instructions.
CARE INSTRUCTIONS:
Wipe clean with a water dampened cloth. Wipe dry with clean cloth.
IMPORTANT:
Keep assembly instructions for future reference.

Enjoy your new RiverRidge® Cabinet!
Thank you for purchasing this RiverRidge® Home item. We hope you
enjoy it and consider purchasing other RiverRidge® items.
To order replacement parts at no cost to you, email [email protected], call
1-(844)-223-5201 or order parts online at www.riverridgehome.com. Only valid in the United States.
If purchased outside of the United States, please contact retailer where purchased.
RiverRidge® is a registered trademark of Sourcing Solutions, Inc., Hudson, WI 54016