RiverRidge Ellsworth 3-Shelf Corner Cabinet User manual

ASSEMBLY INSTRUCTIONS
Ellsworth 3-Shelf Corner Cabinet
ADULT ASSEMBLY REQUIRED
This product requires assembly by an adult because of small parts. Care should be taken
in unpacking and assembling this item to keep small parts away from children. During assembly
children should be kept away from the product due to possible risk of injury.
WARNING SEE FULL WARNING ON PAGE 2
Young children can be seriously injured or killed if furniture tips over. Don’t use
this item for a TV stand or place heavy objects on top of item. Always use
angle-braces or anchors to secure furniture to the wall.

THIS SHELF UNIT WILL HOLD UP TO 25 POUNDS PER SHELF OR A TOTAL OF 75
POUNDS. DO NOT LOAD EACH SHELF WITH MORE THAN 25 POUNDS. IF LOADED
WITH MORE THAN 25 POUNDS PER SHELF AS THIS MAY CAUSE DAMAGE TO THE
SHELF AND MAY CAUSE SERIOUS INJURY OR DEATH.

PARTS LIST
NO
QTY
DESCRIPTION
1
1PC
Top Board
2
1PC
Left Side Support Board
3
1PC
Right Side Support Board
4
1PC
Lower Cross Bar
5
1PC
Right Side Door
6
1PC
Left Side Door
7
1PC
Adjustable Shelf
8
1PC
Bottom Shelf
9
1PC
Left Side Board
10
1PC
Right Side Board

PARTS LIST
NO
PARTS
QTY
DESCRIPTION
A
4PCS
Cam Bolt
B
4PCS
Cam Lock
C
12PCS
Wood Dowel
D
+
1PC
Magnet
E
2PCS
Screw (3x14mm)
F
18PCS
Screw (3x10mm)
G
4PCS
Hinge
H
2PCS
Magnet Plate
I
13PCS
Screw (4x25mm)
J
2PCS
Knob
K
2PCS
Machine Screw (4x18mm)
L
4PCS
Shelf Holder
M
2PCS
Plastic Anchor
N
2PCS
Screw (4x45mm)
TOOLS NEEDED FOR ASSEMBLY: FLAT & PHILIPS SCREWDRIVER (NOT INCLUDED)
THE USE OF A POWER SCREWDRIVER IS NOT RECOMMENDED FOR ASSEMBLY
DO NOT USE ITEM IF ANY PARTS ARE MISSING OR DAMAGED

STEP 1
1. Insert 1 screw (F) through hole on magnet plate (H) and tighten to right side door (5).
2. Insert 4 screws (F) through holes on 2 hinges (G) and tighten to right side door (5).
3. Repeat above steps to assemble magnet plate (H) and 2 hinges (G) to left side door (6).
STEP 2
1. Insert 4 wood dowels (C) into dowel holes on each end of lower cross bar (4).
2. Attach left side support board (2) to lower cross bar (4) by inserting wood dowels into
dowel holes on left side support board (2).
3. Attach right side support board (3) to lower cross bar (4) by inserting wood dowels into
dowel holes on right side support board (3).

STEP 3
1. Attach right side door (5) and left side door (6) to left side support board (2) and right side
support board (3) by inserting 8 screws (F) through holes on hinges (G) on right side door
(5) and left side door (6) and tighten to left side support board (2) and right side support
board (3).
STEP 4
1. Attach bottom shelf (8) to both side support boards (2), (3) by inserting 2 screws (I)
through holes on bottom shelf (8) and tighten to left side support board (2) and right side
support board (3). Do not overtighten.
2. Insert 2 wood dowels (C) into dowel holes on bottom shelf (8).

STEP 5
1. Attach left side panel (9) to shelf (8) and left side support board (2) by inserting 4
screws (I) through holes on left side panel (9) and tighten to shelf (8) and left side
support board (2).
STEP 6
1. Attach right side panel (10) to shelf (8), right side support board (3) and left side panel (9)
by inserting 7 screws (I) through holes on right side panel (10) and tighten to shelf (8),
right side support board (3) and left side panel (9).

STEP 7
1. Screw 4 cam bolts (A) into cam bolt holes on top board (1).
2. Attach magnet (D) to top board (1) by inserting 2 screws (E) through holes on magnet (D)
and tighten to top board (1).
STEP 8
1. Insert 6 wood dowels (C) into dowel holes on end of left side panel (9) and right side
panel (10).
2. Attach top board (1) to left side panel (9) and right side panel (10) by inserting wood
dowels into dowel holes on top board (1) and inserting cam bolts (A) into cam bolt holes
on left side panel (9) and right side panel (10).

STEP 9
1. Insert 4 cam locks (B) into cam lock holes on left side panel (9) and right side panel (10)
and rotate clockwise to lock cam bolts (A) in place.
2. Insert 4 holders (L) into holes on desired position for shelf (7).
3. Attach knob (J) to left side door (6) by inserting 1 machine screw (K) through hole on
left side door (6) and tighten to knob (J).
4. Repeat step 3 to assemble knob (J) to right side door (5).
STEP 10
1. Place adjustable shelf (7) on holders (L).
Option #1: Securing to Drywall
1. Position cabinet against wall in desired location. Using a pencil, make 2 small marks on wall
through holes on side panels. Move cabinet away from wall and screw 2 plastic anchors (M)
into wall on pencil marks.
2. Place cabinet against wall, insert 2 screws (N) through holes on side panels, then tighten to
plastic anchors (M).
Option #2: Securing to Drywall and Wood Stud
1. Position cabinet against wall in desired location. Insert 2 screws (N) through holes on side
panels, then tighten through drywall and into wood stud.

ATTENTION ADULTS: Cabinet should be checked periodically for damage or
loose screws/parts. Take appropriate action necessary to correct hazards such as
tightening of screws and taking any damaged parts away from children.
WARNING Please make sure your item is
secured to the wall, per assembly instructions.
CARE INSTRUCTIONS:
Wipe clean with a water dampened cloth. Wipe dry with clean cloth.
IMPORTANT:
Keep assembly instructions for future reference.

Enjoy your new cabinet!