RiverRidge Madison 06-117 User manual

ASSEMBLY INSTRUCTIONS
RiverRidge®Madison Spacesaver
ITEM #: 06-117 White
ITEM #: 06-118 Gray
ADULT ASSEMBLY REQUIRED
WARNING SEE FULL WARNING ON PAGE 2
This product requires assembly by an adult because of small parts. Care should be taken in
unpacking and assembling this item to keep small parts away from children.
Young children can be seriously injured or killed if furniture tips over.
Don’t use this item for a TV stand or place heavy objects on top of item.
Always use angle-braces or anchors to secure furniture to the wall.

THIS SHELF UNIT WILL HOLD UP TO 25 POUNDS PER SHELF OR A TOTAL OF 75 POUNDS.
DO NOT LOAD EACH SHELF WITH MORE THAN 25 POUNDS. IF LOADED WITH MORE THAN
25 POUNDS PER SHELF, THIS MAY CAUSE DAMAGE TO THE SHELF AND MAY CAUSE
SERIOUS INJURY OR DEATH.

PARTS LIST
15
2
1
3
4
5
6
7
8
9
10
11
12
13
14
16
13
NO QTY DESCRIPTION
1 1PC Top Board
2 1PC Upper Left Side Panel
3 1PC Upper Right Side Panel
4 1PC Lower Left Side Panel
5 1PC Lower Right Side Panel
6 1PC Upper Cross Bar
7 1PC Adjustable Shelf
8 1PC Fixed Shelf
9
10
11
12
13
14
15
16
1PC
1PC
1PC
1PC
2PCS
1PC
1PC
1PC
Open Shelf
Upper Back Panel
Middle Back Panel
Lower Back Panel
Middle Cross Bar
Lower Rear Cross Bar
Left Door
Right Door

TOOLS NEEDED FOR ASSEMBLY: FLAT & PHILLIPS SCREWDRIVER (NOT INCLUDED)
THE USE OF A POWER SCREWDRIVER IS NOT RECOMMENDED FOR ASSEMBLY
DO NOT USE ITEM IF ANY PARTS ARE MISSING OR DAMAGED
To order replacement parts at no cost to you,email [email protected], call
1-(844)-223-5201 or order parts online at www.riverridgehome.com. Only valid in the United States.
If purchased outside of the United States, please contact retailer where purchased.
PARTS LIST
NO QTYPARTS DESCRIPTION
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
16PCS
16PCS
10PCS
4PCS
28PCS
21PCS
2PCS
4PCS
2PCS
2PCS
2PCS
5PCS
2PCS
4PCS
1PC
2PCS
Cam Bolt
Cam Lock
Wood Dowel
Hinge
Screw (4x12mm)
Screw (3x12mm)
Handle
Shelf Holder
Plastic Anchor
Adjustable Anchor Bracket
Screw (4x35mm)
Screw (4x10mm)
Screw (4x30mm)
Silicon pad
Plastic Connection Strip
Screw (4x60mm)

STEP 1
STEP 2
4
4
5
5
A
A
A
A
14
13
13
B
B
B
B
C
C
C
CM
M
M
M
1. Screw 2 cam bolts (A) into pre-threaded holes on lower left side panel (4).
2. Screw 2 cam bolts (A) into pre-threaded holes on lower right side panel (5).
1. Insert 2 wood dowels (C) into wood dowel holes on lower left side panel (4).
2. Attach lower left side panel (4) to 2 middle cross bars (13) by inserting cam bolts (A) into
cam lock holes and wood dowels (C) into wood dowel holes on middle cross bars (13).
3. Insert 2 cam locks (B) into cam lock holes on middle cross bars (13), then rotate clockwise
to secure cam bolts in place.
4. Attach lower rear cross bar (14) to lower left side panel (4) by inserting 2 screws (M)
through holes on lower left side panel (4), then tighten to lower rear cross bar (14).
5. Repeat above steps to assemble lower right side panel (5) to 2 middle cross bars (13)
and lower rear cross bar (14).

STEP 3
STEP 4
C
C
2
2
3
3
A
A
AA
6
8B
B
B
B
1. Screw 2 cam bolts (A) into pre-threaded holes on upper left side panel (2).
2. Screw 2 cam bolts (A) into pre-threaded holes on upper right side panel (3).
1. Insert 1 wood dowel (C) into wood dowel hole on upper cross bar (6).
2. Attach upper cross bar (6) and fixed shelf (8) to upper left side panel (2) by inserting cam
bolts (A) into cam lock holes and wood dowel (C) into wood dowel hole on upper cross
bar (6), and fixed shelf (8).
3. Insert 2 cam locks (B) into cam lock holes on fixed shelf (8), then rotate clockwise to secure
cam bolts in place.
4. Repeat above steps to assemble upper right side panel (3) to upper cross bar (6) and fixed
shelf (8).

STEP 5
STEP 6
A
A
A
A
K
K
J
J
1
B
B
B
B
C
C
2
1
3
6
8
L
1. Screw 4 cam bolts (A) into pre-threaded holes on top board (1).
2. Attach 2 adjustable anchor brackets (J) to top board (1) by inserting 2 screws (K) through
holes on adjustable anchor brackets (J), then tighten to top board (1).
1. Insert 2 wood dowels (C) into wood dowel holes on upper cross bar (6).
2. Attach top board (1) to upper cross bar (6), upper left side panel (2) and upper right side
panel (3) by inserting cam bolts (A) into cam lock holes on upper left side panel (2) and upper
right side panel (3) and inserting wood dowels (C) into wood dowel holes on upper cross bar (6).
3. Insert 4 cam locks (B) into cam lock holes on upper left side panel (2) and upper right side
panel (3), then rotate clockwise to secure cam bolts in place.
4. Insert 1 screw (L) through hole on upper cross bar (6), then tighten to top board (1).

STEP 7
STEP 8
C
C
12
3
9
9
AA
AAL
L
L
L
10
10
10
11
11
11
12
O
OF
F
F
F
F
F
F
FF
1. Screw 4 cam bolts (A) into pre-threaded holes on open shelf (9).
2. Insert 2 wood dowels (C) into wood dowel holes on opposite side of open shelf (9).
3. Attach open shelf (9) to upper left side panel (2) and upper right side panel (3)
by inserting wood dowels (C) into wood dowel holes on upper left side panel (2) and upper
right side panel (3).
4. Insert 4 screws (L) through holes on open shelf (9), then tighten to upper left side panel (2)
and upper right side panel (3).
1. Add 1 plastic connection strip (O) between upper back panel (10) and middle back panel (11);
make sure upper back panel (10) and middle back panel (11) slide into grooves on plastic
connection strip (O).
2. Attach back panels (10), (11), (12) to back of cabinet by inserting 21 screws (F) through
holes on back panels (10), (11), (12), then tighten to back of cabinet.

STEP 9
STEP 10 1
2
3
45
14
1
2
3
9
B
B
4
5
14
13
13
7
H
H
HH
1. Attach lower assembled section to upper assembled section by inserting cam bolts (A) into
cam lock holes on lower left side panel (4) and lower right side panel (5).
2. Insert 4 cam locks (B) into cam lock holes on lower left side panel (4) and lower right side
panel (5), then rotate clockwise to secure cam bolts in place.
1. Insert 4 shelf holders (H) into holes on upper left side panel (2) and upper right side panel (3);
make sure all 4 shelf holders (H) are at same level.
2. Place adjustable shelf (7) onto 4 shelf holders (H).

STEP 11
STEP 12
16
EEEE
EE
P
G
DD
15
16
E
E
1
2
3
4
5
14
E×2
E×2
b
a
a
bc
c
1. Attach 2 hinges (D) to left door (15) by inserting 4 screws (E) through holes on 2 hinges (D),
then tighten to left door (15).
2. Attach 1 handle (G) to bottom of left door (15) by inserting 2 screws (E) through holes on
handle (G), then tighten to bottom of left door (15).
3. Stick 1 silicone pad (P) on handle (G).
4. Repeat above steps to assemble hinges (D) and handle (G) to right door (16).
1. Attach left door (15) to upper left side panel (2) by inserting 8 screws (E) through holes on
hinges (D), then tighten to upper left side panel (2)
2. Attach right door (16) to upper right side panel (3) by inserting 8 screws (E) through holes on
hinges (D), then tighten to upper right side panel (3).
*Note: Tightening screw in position “a” will adjust door up or down; tightening screw in position “b”
will adjust door to or from cabinet and tightening screw in position “c” will adjust door side to side.
15
P
EE
E
EE
E
GD
D

ATTENTION ADULTS: Cabinet should be checked periodically for damage or
loose screws/parts. Take appropriate action necessary to correct hazards such as
tightening of screws and taking any damaged parts away from children.
WARNING Please make sure youritem is
secured to the wall, per assembly instructions.
CARE INSTRUCTIONS:
Wipe clean with a water dampened cloth. Wipe dry with clean cloth.
IMPORTANT: Keep assembly instructions for future reference
STEP 13 I
I
N
N
DRYWALL
WALL ANCHOR
WITH SCREW
SCREW
ONLY
DRYWALL
OPTION #2
OPTION #1
WOOD
STUD
I
I
N
NN
J
Option #1: Securing to Drywall
1. Position spacesaver against wall in desired location. Using a pencil, make 2 small marks on
wall through holes on adjustable anchor brackets (J). Move cabinet away from wall and screw
2 plastic anchors (I) into wall on pencil marks.
2. Place cabinet against wall, insert 2 screws (N) through holes on anchor brackets (J), then
tighten to plastic anchors (I).
Option #2: Securing to Drywall and Wood Stud
1. Position spacesaver against wall in desired location. Insert 2 screws (N) through holes on
adjustable anchor brackets (J), then tighten through drywall and into wood stud.
*Tip: Adjustable anchor brackets (J) can be adjusted to correct distance from wall to cabinet as
needed. Once adjusted, be sure to re-tighten brackets inside cabinet for stability.

Thank you for purchasing this RiverRidge® Home item. We hope you
enjoy it and consider purchasing other RiverRidge® items.
RiverRidge® is a registered trademark of Sourcing Solutions, Inc., Hudson, WI 54016
Enjoy your new RiverRidge®Spacesaver!
To order replacement parts at no cost to you,email [email protected], call
1-(844)-223-5201 or order parts online at www.riverridgehome.com. Only valid in the United States.
If purchased outside of the United States, please contact retailer where purchased.