RiverRidge Somerset 06-039 User manual

ASSEMBLY INSTRUCTIONS
RiverRidge® Somerset 2-Door Wall Cabinet
ITEM #: 06-039 White
ITEM #: 06-078 Gray
ADULT ASSEMBLY REQUIRED
This product requires assembly by an adult because of small parts. Care should be taken
in unpacking and assembling this item to keep small parts away from children. During assembly
children should be kept away from the product due to possible risk of injury.
WARNING SEE FULL WARNING ON PAGE 2
Young children can be seriously injured or killed if furniture tips over. Don’t use
this item for a TV stand or place heavy objects on top of item. Always use
angle-braces or anchors to secure furniture to the wall.

THIS SHELF UNIT WILL HOLD UP TO 25 POUNDS PER SHELF OR A TOTAL OF 75
POUNDS. DO NOT LOAD EACH SHELF WITH MORE THAN 25 POUNDS OR 75 POUNDS
TOTAL WEIGHT. IF OVERLOADED WITH MORE THAN 25 POUNDS PER SHELF OR 75
POUNDS TOTAL WEIGHT, SHELF MAY TIP FROM WALL AND CAUSE SERIOUS INJURY
OR DEATH.

PARTS LIST
NO
QTY
DESCRIPTION
1
1PC
Left Door
2
1PC
Right Door
3
1PC
Right Side Panel
4
1PC
Left Side Panel
5
1PC
Cross Bar
6
1PC
Shelf
7
1PC
Top Board
8
1PC
Bottom Board
9
1PC
Upper Back Board
10
1PC
Middle Back Board
11
1PC
Lower Back Board
12
1PC
Adjustable Shelf
13
1PC
Right Support Board
14
1PC
Left Support Board

NO
PARTS
QTY
DESCRIPTION
A
16PCS
Wood Dowel
B
12PCS
Cam Bolt
C
12PCS
Cam Lock
D
18PCS
Screw (3x12mm)
E
4PCS
Hinge
F
2PCS
Magnet Plate
G
24PCS
Screw (2.5x12mm)
H
1SET
Magnet with 2 Screws
I
4PCS
Shelf Holder
J
4PCS
Machine Screw (4x12mm)
K
2PCS
Handle
L
2PCS
Plastic Anchor
M
2PCS
Screw (4x45mm)
N
1PC
Plastic Connection Strip
1PC
Wall Mounting Paper Template
TOOLS NEEDED FOR ASSEMBLY: FLAT & PHILLIPS SCREWDRIVER (NOT INCLUDED)
THE USE OF A POWER SCREWDRIVER IS NOT RECOMMENDED FOR ASSEMBLY
DO NOT USE ITEM IF ANY PARTS ARE MISSING OR DAMAGED
To order replacement parts at no cost to you, email [e-mail], call
1-(844)-223-5201 or order parts online at www.riverridgehome.com. Only valid in the United States.
If purchased outside of the United States, please contact retailer where purchased.

STEP 1
1. Attach 1 magnet plate (F) to left door (1) by inserting 1 screw (D) through hole on magnet
plate (F), then tighten to left door (1).
2. Attach 1 handle (K) to left door (1) by inserting 2 machine screws (J) through holes on left
door (1), then tighten to handle (K).
3. Repeat above steps to assemble another magnet plate (F) and handle (K) to right door (2).
STEP 2
1. Screw 3 cam bolts (B) into cam bolt holes on right support board (13).
2. Attach 2 metal hinges (E) to right support board (13) by inserting 4 screws (D) through
holes on metal hinges (E), then tighten to right support board (13).
3. Repeat above steps for left support board (14).

STEP 3
1. Attach left support board (14) to left side panel (4) by inserting 3 cam bolts (B) into cam
lock holes on left side panel (4).
2. Insert 3 cam locks (C) into cam lock holes on left side panel (4), then rotate clockwise to
secure cam bolts (B) in place.
3. Repeat above steps to assemble right side panel (3) and right support board (13).
STEP 4
1. Screw 2 cam bolts (B) into cam bolt holes on left side panel (4) and right side panel (3).
2. Insert 8 wood dowels (A) into dowel holes on left side panel (4) and right side panel (3).
3. Attach cross bar (5) to left side panel (4) by inserting wood dowels (A) into dowel holes on
cross bar (5).
4. Attach shelf (6) to left side panel (4) by inserting 1 cam bolt (B) and 2 wood dowels (A) into
holes on shelf (6), then insert 1 cam lock (C) into cam lock hole on shelf (6) and rotate
clockwise to secure cam bolt (B) in place.
5. Attach right side panel (3) to cross bar (5) and shelf (6) by inserting wood dowels (A) into
holes on cross bar (5), and inserting cam bolt (B) and wood dowels (A) into holes on shelf (6).
6. Insert 1 cam lock (C) into cam lock hole on shelf (6) and rotate clockwise to secure cam
bolt (B) in place.

STEP 5
1. Screw 2 cam bolts (B) into the cam bolt holes on bottom board (8).
2. Insert 4 wood dowels (A) into dowel holes on bottom board (8).
3. Attach bottom board (8) to left side panel (4) and right side panel (3) by inserting cam bolts
(B) and wood dowels (A) into holes on left side panel (4) and right side panel (3).
4. Insert 2 cam locks (C) into cam lock holes on left side panel (4) and right side panel (3),
then rotate clockwise to secure cam bolts (B) in place.
5. Attach magnet (H) to top board (7) by inserting 2 screws (H) through holes on magnet (H),
then tighten to bottom of top board (7).
6. Screw 2 cam bolts (B) into cam bolt holes on top board (7).
7. Insert 4 wood dowels (A) into dowel holes on the bottom of top board (7).
8. Attach top board (7) to left side panel (4) and right side panel (3) by inserting 4 wood dowels
(A) and 2 cam bolts (B) into dowel holes and cam lock holes on left side panel (4) and right
side panel (3).
9. Insert 2 cam locks (C) into cam lock holes on left side panel (4) and right side panel (3),
then rotate clockwise to secure cam bolts (B) in place.

STEP 6
1. Attach upper back board (9) and middle back board (10) together by sliding into plastic
connection strip (N).
2. Attach upper back board (9) and middle back board (10) to cabinet by inserting screws (G)
through holes on upper back board (9) and middle back board (10), then tighten into
cabinet.
3. Attach lower back board (11) to cabinet by inserting screws (G) through holes on lower
back board (11), then tighten into cabinet.
STEP 7
1. Attach left door (1) to left support panel (14) by inserting 4 screws (D) through holes on
metal hinges (E), then tighten to left door (1).
2. Repeat above step to assemble right door (2).

STEP 8
Option #1: Securing to Drywall
1. Using wall mounting paper template to determine position, screw 2 plastic anchors (L) into
drywall.
2. Insert 2 screws (M) through holes on inside of cabinet and into plastic anchors (L) and tighten.
Option #2: Securing to Drywall and Wood Stud
1. Insert 2 screws (M) through holes on inside of cabinet, then tighten through drywall and into
wood stud.
STEP 9
1. Insert 4 shelf holders (I) into holes on left side panel (4) and right side panel (3) at desired
shelf heights.
2. Place adjustable shelf (12) onto shelf holders (I).

ATTENTION ADULTS: Cabinet should be checked periodically for damage or
loose screws/parts. Take appropriate action necessary to correct hazards such as
tightening of screws and taking any damaged parts away from children.
WARNING Please make sure your item is
secured to the wall, per assembly instructions.
CARE INSTRUCTIONS:
Wipe clean with a water dampened cloth. Wipe dry with clean cloth.
IMPORTANT:
Keep assembly instructions for future reference.

Enjoy your new RiverRidge® Cabinet!
Thank you for purchasing this RiverRidge® Home item. We hope you
enjoy it and consider purchasing other RiverRidge® items.
To order replacement parts at no cost to you, email [email protected], call
1-(844)-223-5201 or order parts online at www.riverridgehome.com. Only valid in the United States.
If purchased outside of the United States, please contact retailer where purchased.
RiverRidge® is a registered trademark of Sourcing Solutions, Inc., Hudson, WI 54016