RiverRidge MEDORD 06-102 User manual

ASSEMBLY INSTRUCTIONS
RiverRidge® MEDORD SINGLE DOOR FLOOR CABINET
ITEM# 06-102WHITE
ITEM# 06-103ESPRESSO
ADULT ASSEMBLY REQUIRED
This product requires assembly by an adult because of small parts. Care should be taken
in unpacking and assembling this item to keep small parts away from children.
WARNING SEE FULL WARNING ON PAGE 2
Young children can be seriously injured or killed if furniture tips over. Don’t use this
item for a TV stand or place heavy objects on top of item. Always use angle-braces or
anchors to secure furniture to the wall.

Send requests for missing or damaged parts by email to: [e-mail] or
call toll free 1-(844)-223-5201 or order parts on line at www.riverridgehome.com
THIS CABINET WILL HOLD UP TO 25 POUNDS PER SHELF OR A TOTAL OF 75 POUNDS. DO NOT
LOAD EACH SHELF WITH MORE THAN 25 POUNDS OR 75 POUNDS TOTAL WEIGHT. IF
OVERLOADED WITH MORE THAN 25 POUNDS PER SHELF OR 75 POUNDS TOTAL WEIGHT,
CABINET MAY TIP FROM WALL AND CAUSE SERIOUS INJURY OR DEATH.

PARTS LIST
NO QTY DESCRIPTION
1 1PC TOP BOARD
2 1PC LEFT SIDE PANEL
3 1PC RIGHT SIDE PANEL
4 1PC CROSS BAR
5 1PC BACK BOARD
6 1PC DOOR
7 1PC ADJUSTABLE SHELF
8 1PC BOTTOM BOARD
9 1PC DRAWER FRONT BOARD
10 1PC DRAWER LEFT SIDE PANEL
11 1PC DRAWER RIGHT SIDE PANEL
12 1PC DRAWER BACK BOARD
13 1PC DRAWER BOTTOM BOARD

NO PARTS QTY DESCRIPTION
A
10PCS CAM BOLT 5x35mm
B
10PCS CAM LOCK 15x10mm
C 4PCS WOOD DOWEL
D
1PC MAGNET
E 6PCS SCREW 3x14mm
F 2PCS METAL BRACKET
G 2PCS SCREW 3x10mm
H 4PCS SHELF HOLDER
I
5PCS SCREW 4x35mm
J
1PC MAGNET PLATE
K
2PCS DOOR PIN
L
2PCS SCREW 4x25mm
M
2PCS KNOB
N
1PC PLASTIC LOCK STRIP
O
1PC PLASTIC ANCHOR
P
4PCS PLASTIC BRACKET
Q
4PCS CAM BOLT 5x25mm
R 4PCS CAM LOCK 12x10mm
S 8PCS SCREW 3x12mm
T
1PC
DRAWER SLIDER (ATTACH TO
LEFT SIDE PANEL)
U
1PC
DRAWER SLIDER (ATTACH TO
RIGHT SIDE PANEL)
V
1PC
DRAWER SLIDER (ATTACH TO
DRAWER RIGHT SIDE PANEL)
W
1PC
DRAWER SLIDER (ATTACH TO
DRAWER LEFT SIDE PANEL)
TOOLS NEEDED FOR ASSEMBLY: FLAT & PHILLIPS SCREWDRIVER (NOT INCLUDED)
THE USE OF POWER SCREWDRIVER IS NOT RECOMMENDED FOR ASSEMBLY
TOOL NEEDED FOR SECURING TO WALL: POWER DRILL (NOT INCLUDED)

STEP 1
STEP 1
1. Screw 4 cam bolts (A) into pre-threaded holes on top board (1).
2. Attach 1 metal bracket (F) to top board (1) by inserting 1 screw (G) through hole on metal bracket (F)
and tighten to top board (1).
3. Attach magnet plate (J) to door (6) by inserting 1 screw (G) through hole on magnet plate (J) and
tighten to door (6)
4. Attach 1 knob (M) to door (6) by inserting 1 screw (L) through hole on door (6) and tighten to knob (M).
5. Insert 2 door pins (K) into holes on door (6).
STEP 2
STEP 2
1. Screw 3 cam bolts (A) into pre-threaded holes on left side panel (2).
2. Attach drawer slider (T) to left side panel (2) by inserting 2 screws (S) through screw holes on drawer
slider (T) and tighten to left side panel (2).
3. Screw 3 cam bolts (A) into pre-threaded holes on right side panel (3).
4. Attach drawer slider (U) to right side panel (3) by inserting 2 screws (S) through screw holes on drawer
slider (U) and tighten to right side panel (3).

STEP 3
STEP 3
1. Attach magnet (D) to cross bar (4) by inserting 2 screws (E) through holes on magnet (D) and tighten to
cross bar (4).
2. Insert 2 wood dowels (C) into wood dowel holes on left side panel (2).
3. Attach cross bar (4) and bottom board (8) to left side panel (2) by inserting wood dowels (C) into wood
dowel holes on cross bar (4) and bottom board (8).
4. Insert 3 cam locks (B) into cam lock holes on cross bar (4) and bottom board (8), then rotate clockwise
to secure cam bolts in place.
STEP 4
STEP 4
1. Attach door (6) to cross bar (4) and bottom board (8) by inserting door pin (K) into door pin holes on
cross bar (4) and bottom board (8).

STEP 5
STEP 5
1. Insert 2 wood dowels (C) into wood dowel holes on cross bar (4) and bottom board (8).
2. Attach right side panel (3) to cross bar (4) and bottom board (8) by inserting wood dowels (C) into wood
dowel holes on right side panel (3).
3. Insert 3 cam locks (B) into cam lock holes on cross bar (4) and bottom board (8), then rotate clockwise
to secure cam bolts in place.
STEP 6
STEP 6
1. Slide back board (5) into grooves on left side panel (2), right side panel (3) and bottom board (8).
2. Attach top board (1) to left side panel (2), right side panel (3) and back board (5) by aligning groove on
top board (1) with back board (5) and inserting cam bolts (A) into cam lock holes on left side panel (2)
and right side panel (3).
3. Insert 4 cam locks (B) into cam lock holes on left side panel (2) and right side panel (3), then rotate
clockwise to secure cam bolts in place.

STEP 7
STEP 7
1. Screw 4 cam bolts (Q) into pre-threaded holes on drawer front board (9).
2. Attach drawer left side panel (10) and drawer right side panel (11) to drawer back board (12) by
inserting 4 screws (I) through holes on drawer left side panel (10) and drawer right side panel (11),
then tighten to drawer back board (12).
3. Slide drawer bottom board (13) into grooves on drawer left side panel (10), drawer right side panel
(11) and drawer back board (12).
STEP 8
STEP 8
1. Attach drawer front board (9) to drawer left side panel (10), drawer right side panel (11) and drawer
bottom board (13) by inserting cam bolts (Q) into cam lock holes on drawer left side panel (10) and
drawer right side panel (11).
2. Insert 4 cam locks (R) into cam lock holes on drawer left side panel (10) and drawer right side panel (11)
and rotate clockwise to secure cam bolts in place.
3. Attach knob (M) to drawer front board (9) by inserting 1 screw (L) through hole on drawer front board (9)
and tighten to knob (M).

STEP 9
STEP 9
1. Attach drawer slider (V) and (W) to bottom of assembled drawer by inserting 4 screws (S) through holes
on drawer slider (V) and (W), then tighten to bottom of assembled drawer.
STEP 10
STEP 10
1. Slide assembled drawer into cabinet.
2. Insert 4 shelf holders (H) into holes on left side panel (2) and right side panel (3) and make sure all 4
plastic holders (H) are on same level.
3. Place adjustable shelf (7) on the plastic holders.

STEP 11
STEP 11
1.Attach 4 brackets (P) to back of cabinet by inserting 4 screws (E) through holes on brackets (P) and
tighten to cabinet.
STEP 12
STEP 12
1. Place drawing with hole position on wall in desired location and drill 1 hole through the hole position on
the drawing.
2. Insert plastic anchor (O) into hole on wall and attach metal bracket (F) to plastic anchor (O) by inserting
1 screw (I) through hole on metal bracket (F) and tighten to plastic anchor (O).
3. Place cabinet against wall to align brackets and insert Plastic lock strip (N) through metal bracket (F) on
cabinet and metal bracket (F) on wall.
4. Fasten plastic lock strip (N) to secure 2 metal brackets together firmly.