Rohde & Schwarz R&S ATS1000 Manual

R&S®ATS1000
Antenna Test System
Instructions Handbook
1179298302
Version 01
(;ÝMá2)

Original instructions, referred to below as "this handbook".
It describes the following models of the antenna test system:
●R&S®ATS1000, Version 02, order no. 1532.1010K02
●R&S®ATS1000, Version 03, order no. 1532.1010K03
The antenna test system is also referred to as the "chamber" or the "product".
The software contained in this product uses several valuable open source software packages. For information, see the "Open
Source Acknowledgment" document, which is available for download from the R&S ATS1000 product page at www.rohde-
schwarz.com/product/ats1000 > Software.
Rohde & Schwarz would like to thank the open source community for their valuable contribution to embedded computing.
© 2020 Rohde & Schwarz GmbH & Co. KG
Mühldorfstr. 15, 81671 München, Germany
Phone: [phone] - 0
Email: [email protected]
Internet: www.rohde-schwarz.com
Subject to change – data without tolerance limits is not binding.
R&S® is a registered trademark of Rohde & Schwarz GmbH & Co. KG.
Trade names are trademarks of the owners.
1179.2983.02 | Version 01 | R&S®ATS1000
Throughout this handbook, the names of Rohde & Schwarz products appear without the ® symbol, e.g. R&S®ATS1000 is given as
R&S ATS1000.

Contents
R&S®ATS1000
3Instructions Handbook 1179.2983.02 ─ 01
Contents
1 Introduction............................................................................................ 7
1.1 Regulatory Information.................................................................................................7
1.1.1 CE Declaration................................................................................................................ 7
1.1.2 Korea Certification Class B............................................................................................. 7
1.1.3 China RoHS Certification................................................................................................ 8
1.2 Documentation Overview............................................................................................. 8
1.2.1 Instructions Handbook.................................................................................................... 8
1.2.2 Configuration Manual...................................................................................................... 8
1.2.3 Data Sheets and Brochures............................................................................................ 8
1.2.4 Open Source Acknowledgment (OSA)............................................................................9
1.2.5 Application Notes, Application Cards, White Papers, etc................................................9
1.2.6 Help.................................................................................................................................9
1.3 Conventions.................................................................................................................. 9
2 Safety.....................................................................................................11
2.1 Intended Use................................................................................................................11
2.2 Residual Risks.............................................................................................................11
2.3 Potentially Dangerous Situations..............................................................................13
2.4 Warning Messages in This Handbook.......................................................................15
2.5 Labels on the Chamber.............................................................................................. 15
3 Emergencies.........................................................................................17
3.1 Emergency Stop..........................................................................................................17
4 Machine Overview................................................................................18
4.1 Interlock Systems....................................................................................................... 23
4.2 DUT Alignment Lasers................................................................................................25
4.3 Positioner.....................................................................................................................25
4.3.1 Third-Party Positioning Equipment................................................................................26
5 Transportation, Handling and Storage...............................................29
5.1 Moving the Chamber...................................................................................................29
5.2 Packing........................................................................................................................ 30
5.3 Transport......................................................................................................................33

Contents
R&S®ATS1000
4Instructions Handbook 1179.2983.02 ─ 01
5.4 Storage.........................................................................................................................33
6 Installation and Commissioning.........................................................35
6.1 Choosing the Operating Site......................................................................................35
6.2 Unpacking and Checking........................................................................................... 36
6.3 Installing the Chamber............................................................................................... 38
6.4 Connecting to Power.................................................................................................. 39
6.5 Connecting to Control................................................................................................ 40
6.6 Connecting Test Equipment.......................................................................................41
6.7 Testing Safety Systems.............................................................................................. 41
7 Operation.............................................................................................. 43
7.1 Activating the Chamber..............................................................................................43
7.2 Deactivating the Chamber..........................................................................................43
7.3 Operating the Door..................................................................................................... 44
7.3.1 Door Status................................................................................................................... 44
7.3.2 Referencing the Door's Lock......................................................................................... 45
7.3.3 Opening the Door..........................................................................................................46
7.3.4 Closing the Door........................................................................................................... 46
7.4 Placing a DUT in the Chamber...................................................................................46
7.4.1 DUT Mass and Eccentricity...........................................................................................49
7.4.2 Metal DUT Holder Set................................................................................................... 49
7.4.3 Telescopic Tube DUT Holder........................................................................................ 51
7.4.4 Rohacell DUT Holder.................................................................................................... 51
7.4.5 PCB Holder Set.............................................................................................................52
7.5 Connecting a DUT....................................................................................................... 55
7.6 Operating the Positioning System............................................................................ 56
7.6.1 Moving the Elevation Positioner....................................................................................60
7.6.2 Moving the Azimuth Turntable.......................................................................................61
7.6.3 Combining the Elevation and Azimuth Movements.......................................................62
7.7 Preparing for Shift End...............................................................................................64
8 Inspection and Maintenance...............................................................65
8.1 Recommended Intervals.............................................................................................65
8.2 Regular Safety Inspections........................................................................................ 65

Contents
R&S®ATS1000
5Instructions Handbook 1179.2983.02 ─ 01
8.3 Preparing the Chamber for Maintenance..................................................................66
8.4 Performing Maintenance Tasks................................................................................. 66
8.4.1 Daily Functional Check................................................................................................. 66
8.4.2 Checking the Absorber..................................................................................................67
8.4.3 Cleaning........................................................................................................................ 67
8.4.4 Lubricating the Turntable's Telescopic Tube................................................................. 69
8.4.5 System Calibration........................................................................................................ 70
9 Troubleshooting and Repair............................................................... 71
9.1 Chamber Troubleshooting......................................................................................... 71
9.2 Positioner Troubleshooting....................................................................................... 73
9.2.1 Positioner Loses Absolute Position...............................................................................73
9.2.2 Unusual Noise from Positioner......................................................................................73
9.3 Contacting Customer Support...................................................................................74
10 Disabling and Scrapping.....................................................................75
10.1 Taking Out of Commission.........................................................................................75
10.2 Disposal....................................................................................................................... 76
Glossary: List of Frequently Used Terms and Abbreviations..........77
Index......................................................................................................80

Contents
R&S®ATS1000
6Instructions Handbook 1179.2983.02 ─ 01

Introduction
R&S®ATS1000
7Instructions Handbook 1179.2983.02 ─ 01
1 Introduction
This instructions handbook addresses every user of the chamber (also referred to as
the product). To use the chamber safely, first read and understand this entire hand-
book. If you are unsure about a topic, ask your supervisor or contact Rohde & Schwarz
customer support.
The instructions handbook helps you to use the chamber safely and efficiently during
its entire lifecycle; installation, operation, maintenance and disabling. If you are only
involved in one part of the lifecycle, focus on the chapter about that topic. But always
get a deep understanding of the safety aspects described in Chapter 2, "Safety",
on page 11 before starting.
The chapter titles give a clear idea of the lifecycle stage and the tasks described. For
example, if you are an operator, most activities intended for you are described in Chap-
ter 7, "Operation", on page 43. If tasks are restricted to certain roles, these roles are
mentioned at the beginning of the chapter that describes the tasks. The roles are
explained in the glossary.
Abbreviations and frequently used terms are explained in the glossary at the end of
this handbook.
1.1 Regulatory Information
The following labels and the associated certificates declare conformance with legal
regulations.
1.1.1 CE Declaration
Certifies compliance with the applicable provisions of the Directive of the Council of the
European Union. A copy of the CE declaration in English is at the beginning of the prin-
ted version of this handbook.
1.1.2 Korea Certification Class B
이 기기는 가정용(B급) 전자파 적합기기로서 주로 가정에서 사용하는 것을 목적으로 하
며, 모든 지역에서 사용할 수 있습니다.
Regulatory Information

Introduction
R&S®ATS1000
8Instructions Handbook 1179.2983.02 ─ 01
1.1.3 China RoHS Certification
Certifies compliance with the Chinese government's regulation on the restriction of
hazardous substances (RoHS).
The chamber is built of environmentally sound materials. It is free of substances that
are either restricted or prohibited by law.
1.2 Documentation Overview
This section provides an overview of the R&S ATS1000 user documentation. Unless
specified otherwise, you find the documents on the R&S ATS1000 product page at:
www.rohde-schwarz.com/product/ats1000
1.2.1 Instructions Handbook
This handbook describes all operating modes and functions of the chamber. It also pro-
vides information on maintenance, interfaces and error messages.
The handbook does not describe the special activities required for permitted hardware
reconfigurations of the chamber, which are described in the Configuration Manual.
Only an expert user who has read and understood the Configuration Manual is allowed
to perform reconfigurations. Other users are limited to tasks described in the instruc-
tions handbook.
A printed copy of this handbook is included in the delivery and available at:
www.rohde-schwarz.com/manual/ats1000
1.2.2 Configuration Manual
Describes all permissible hardware reconfigurations and adjustments of the chamber.
These activities are restricted to the role of an expert user who has read and under-
stood the Configuration Manual and who has all skills required for reconfiguring the
chamber.
The configuration manual is available for registered users on the global
Rohde & Schwarz information system (GLORIS):
gloris.rohde-schwarz.com > Support & Services > Sales Web > Test and Measurement
> Wireless Communication > ATS1000 > Manuals
1.2.3 Data Sheets and Brochures
The data sheet contains the technical specifications of the chamber. It also lists
optional accessories and their order numbers.
Documentation Overview

Introduction
R&S®ATS1000
9Instructions Handbook 1179.2983.02 ─ 01
The brochure provides an overview of the chamber and describes its specific features
and characteristics.
See www.rohde-schwarz.com/brochure-datasheet/ats1000
1.2.4 Open Source Acknowledgment (OSA)
The open source acknowledgment provides verbatim license texts of the used open-
source software.
See www.rohde-schwarz.com/software/ats1000
1.2.5 Application Notes, Application Cards, White Papers, etc.
These documents deal with special applications or background information on particu-
lar topics.
See www.rohde-schwarz.com/application/ats1000
1.2.6 Help
The help system that is embedded in the R&S RF Test Suite provides information for
the R&S EMC32, R&S AMS32 and R&S WMS32 software packages. The R&S AMS32
software package communicates with the NCD controller. For help, navigate to this
part of the help system.
1.3 Conventions
The R&S ATS1000 is also referred to as the "chamber" or the "product".
The following text markings are used throughout this handbook:
Convention Description
[Keys] Names of connectors, keys and knobs are placed between square
brackets.
Filenames, commands,
program code
Filenames, commands, coding samples and screen output are distin-
guished by their font.
Links Clickable links are shown in blue font.
bold or italic Highlighted text is shown in bold or italic font.
"quote" Quoted text or terms are placed between quotation marks.
Tip
Tips are indicated as in this example and provide useful hints or alternative solutions.
Conventions

Introduction
R&S®ATS1000
10Instructions Handbook 1179.2983.02 ─ 01
Note
Notes are indicated as in this example and provide important additional information.
Conventions