Ronbow Signature series Assembly instructions

INSTALLATION AND CARE GUIDE
42” VENTO LED MIRROR CABINET
E095614

VENTO 42” LED Mirror Cabinet
Model : E095614 Designed By: PININFARINA | ITALY
161018ronbow.eu | ronbow.comINSTALLATION SHEET
1
Tools Required
PRE-INSTALLATION
ALL WIRING SHOULD BE DONE BY A QUALIFIED LICENSED ELECTRICIAN.
WARNING: To reduce the risk of electrical shock, shut o power before wiring the cabinet.
CAUTION: Requires 120V 20AMP circuit.
CAUTION: The LED mirror must be wired to a GFI (ground fault interrupter) circuit breaker when used in
bathrooms and all other locations required by the national electric code.
120VAC
20A GFI
CIRCUIT BREAKER FIELD CONNECTION LED MIRROR CABINET
White = Negative
Green= Ground
Black= Positive
White = Negative
LED
Black= Positive
Green= Ground
6 long screws
1 set of wall cleats
1 2x4 beam
1 electrical box
3 wire nuts
Materials Included
Materials Required

VENTO 42” LED Mirror Cabinet
Model : E095614 Designed By: PININFARINA | ITALY
161018ronbow.eu | ronbow.comINSTALLATION SHEET
2
See Figure 1.
Step 1: Determine the ideal location of your
new mirror cabinet. Make sure mirror
cabinet has enough clearance from
faucet and ceiling.
Figure 1.
Minimum to Faucet
Minimum to Ceiling1”
1”
See Figure 2.
Step 2: Determine the location of wall cleats.
Make sure to use the leveling tool to
ensure the pilot holes are level.
Drill pilot holes into the wall.
NOTE: It is highly recommended
to include a 2x4 horizontal beam
between 2 studs to add stability.
Front notch the 2 studs and place
the 2x4 beam between the studs.
Figure 2.
Step 3: Fasten the screws provided into the
wall to secure the wall cleat.
INSTALLATION
2 x 4

VENTO 42” LED Mirror Cabinet
Model : E095614 Designed By: PININFARINA | ITALY
161018ronbow.eu | ronbow.comINSTALLATION SHEET
3
Step 4: Cut an opening in the wall and connect
the electrical wires to the housing.
NOTE: Run electrical wires to
the opening. An electrical box is
recommended inside the opening.
Figure 3.
Figure 4.
See Figure 3.
Step 5: Secure the cleats in the back of the
mirror cabinet to the wall cleat. Hide all
wires in the opening.
See Figure 4.
Step 6: Remove the three top screws of the
LED light cover.

VENTO 42” LED Mirror Cabinet
Model : E095614 Designed By: PININFARINA | ITALY
161018ronbow.eu | ronbow.comINSTALLATION SHEET
4
Figure 5.
See Figure 5.
Step 7: Tighten the bottom screw of the
mounting brackets until mirror
cabinet is flush against the wall.

VENTO 42” LED Mirror Cabinet
Model : E095614 Designed By: PININFARINA | ITALY
161018ronbow.eu | ronbow.comINSTALLATION SHEET
5
Wood Surfaces
Recommended Products
The fine furniture finish of your new vanity, mirror or other bathroom accessories are designed to
protect against normal home use. With proper care, your product will provide years of use and beauty
in your home.
General Care Tips
PRODUCT CARE AND MAINTENANCE
• If a spill occurs, clean and dry the surface immediately as liquid can soak through the surface and cause
greater damage.
• Do not place in direct sunlight. Exposure to sunlight may affect the appearance of your vanity, and the
finish will eventually crack.
• Keep away from direct sources of extreme temperatures as heat, cold or moisture from humidity.
Color changes, or blemishes in the wood can occur if recommended care of is not met. Try to avoid
these extremes.
• Most wood surfaces can be cleaned, or dusted, with any commercial wood cleaning product. For general
cleaning, use a non-abrasive, or lint-free cloth while dusting along the wood grain to preserve the
wood’s chacteristics.
• Pledge Orange Oil, or similar
• Orange-Glo Wood Cleaner
DISCLAIMERS: Wood naturally ages, darkens and changes color over time due to several environmental conditions that may cause materials to vary from their
original color and/or to warp, split or crack. These variations are considered to be the nature of the material in relation to their environmental exposure and may
be significant over a long period of time. The eectiveness of cleaning Ronbow product is dependant on various factors that include sunlight, smoke, moisture,
household cleaners and/or amount of cleaning product used over time. Ronbow cannot guarantee that the above Product Care & Maintenance methods will
eectively clean your product.
• Test cleaning product on small, discrete area prior to applying to entire surface.
• Wipe surfaces frequently with dry, soft, non-abrasive and lint-free towel.
• Do not allow liquids and moisture to accumulate on the surface of products.
• For warranty information, please visit our website at www.ronbow.com or contact the Customer Service
Department at [phone].

161018
40650 Encyclopedia Circle
Fremont, CA 94538
T 510.713.1188
F 510.657.9388 ronbow.eu | ronbow.com