Ronbow SIGNATURE E075614 Assembly instructions

INSTALLATION AND CARE GUIDE
43” PURE LED MIRROR CABINET
E075614

PURE LED Mirror Cabinet
Model : E075614 Designed By: ALEXANDER ZHUKOVSKY | RUSSIA
161018ronbow.eu | ronbow.comINSTALLATION SHEET
1
Tools Required
PRE-INSTALLATION
ALL WIRING SHOULD BE DONE BY A QUALIFIED LICENSED ELECTRICIAN.
WARNING: To reduce the risk of electrical shock, shut o power before wiring the cabinet.
CAUTION: Requires 120V 20AMP circuit.
CAUTION: The LED mirror must be wired to a GFI (ground fault interrupter) circuit breaker when used in
bathrooms and all other locations required by the national electric code.
120VAC
20A GFI
CIRCUIT BREAKER FIELD CONNECTION LED MIRROR CABINET
White = Negative
Green= Ground
Black= Positive
White = Negative
LED
Black= Positive
Green= Ground
6 long screws
1 set of wall cleats
1 2x4 beam
1 electrical box
3 wire nuts
Materials Included
Materials Required

PURE LED Mirror Cabinet
Model : E075614 Designed By: ALEXANDER ZHUKOVSKY | RUSSIA
161018ronbow.eu | ronbow.comINSTALLATION SHEET
2
See Figure 1.
Step 1: Determine the ideal location of your
new mirror. Make sure mirror has
enough clearance from faucet
and ceiling.
Figure 1.
Minimum to Faucet
Minimum to Ceiling1”
1”
See Figure 2.
Step 2: Determine the location of wall cleat.
Make sure to use the leveling tool to
ensure the pilot holes are level.
Drill pilot holes into the wall.
NOTE: It is highly recommended
to include a 2x4 horizontal beam
between 2 studs to add stability. Front
notch the 2 studs and place the 2x4
beam between the studs. Figure 2.
Step 3: Cut a rough opening in the dry wall
below the 2x4. This will be used for the
electrical box.
INSTALLATION
2x4 beam

PURE LED Mirror Cabinet
Model : E075614 Designed By: ALEXANDER ZHUKOVSKY | RUSSIA
161018ronbow.eu | ronbow.comINSTALLATION SHEET
3
Step 4: Connect the electrical wires to the
housing.
NOTE: Run electrical wires to
the opening. An electrical box is
recommended inside the opening.
Figure 3.
Figure 4.
See Figure 3.
Step 5: Attach the wall cleat to the wall where
the horizontal beam was installed.
Secure the wall cleat using the long
screws provided.
Verify the cleat is level.
See Figure 4.
Step 6: Attach the wires from the cabinet to
the electrical box and lift and gently
place the cabinet on the wall cleat.
Verify the cabinet is level.

PURE LED Mirror Cabinet
Model : E075614 Designed By: ALEXANDER ZHUKOVSKY | RUSSIA
161018ronbow.eu | ronbow.comINSTALLATION SHEET
4
Wood Surfaces
Recommended Products
The fine furniture finish of your new vanity, mirror or other bathroom accessories are designed to
protect against normal home use. With proper care, your product will provide years of use and beauty
in your home.
General Care Tips
PRODUCT CARE AND MAINTENANCE
• If a spill occurs, clean and dry the surface immediately as liquid can soak through the surface and cause
greater damage.
• Do not place in direct sunlight. Exposure to sunlight may affect the appearance of your vanity, and the
finish will eventually crack.
• Keep away from direct sources of extreme temperatures as heat, cold or moisture from humidity.
Color changes, or blemishes in the wood can occur if recommended care of is not met. Try to avoid
these extremes.
• Most wood surfaces can be cleaned, or dusted, with any commercial wood cleaning product. For general
cleaning, use a non-abrasive, or lint-free cloth while dusting along the wood grain to preserve the
wood’s chacteristics.
• Pledge Orange Oil, or similar
• Orange-Glo Wood Cleaner
DISCLAIMERS: Wood naturally ages, darkens and changes color over time due to several environmental conditions that may cause materials to vary from their
original color and/or to warp, split or crack. These variations are considered to be the nature of the material in relation to their environmental exposure and may
be significant over a long period of time. The eectiveness of cleaning Ronbow product is dependant on various factors that include sunlight, smoke, moisture,
household cleaners and/or amount of cleaning product used over time. Ronbow cannot guarantee that the above Product Care & Maintenance methods will
eectively clean your product.
• Test cleaning product on small, discrete area prior to applying to entire surface.
• Wipe surfaces frequently with dry, soft, non-abrasive and lint-free towel.
• Do not allow liquids and moisture to accumulate on the surface of products.
• For warranty information, please visit our website at www.ronbow.com or contact the Customer Service
Department at [phone].

160926
40650 Encyclopedia Circle
Fremont, CA 94538
T 510.713.1188
F 510.657.9388 ronbow.eu | ronbow.com