Ronbow SIGNATUTE Series Assembly instructions

INSTALLATION AND CARE GUIDE
UNITY LED MIRROR CABINET
E045612
E045614

UNITY LED Mirror Cabinet
Model : E045612
E045614
Designed By: KURZ KURZ DESIGN | GERMANY
161020ronbow.eu | ronbow.comINSTALLATION SHEET
1
Tools Required
PRE-INSTALLATION
ALL WIRING SHOULD BE DONE BY A QUALIFIED LICENSED ELECTRICIAN.
WARNING: To reduce the risk of electrical shock, shut o power before wiring the cabinet.
CAUTION: Requires 120V 20AMP circuit.
CAUTION: The LED mirror must be wired to a GFI (ground fault interrupter) circuit breaker when used in
bathrooms and all other locations required by the national electric code.
120VAC
20A GFI
CIRCUIT BREAKER FIELD CONNECTION LED MIRROR CABINET
White = Negative
Green= Ground
Black= Positive
White = Negative
LED
Black= Positive
Green= Ground
1 reflector
1 set of wall cleats
4 long screws
1 2x4 beam
1 electrical box
3 wire nuts
Materials Included
Materials Required

UNITY LED Mirror Cabinet
Model : E045612
E045614
Designed By: KURZ KURZ DESIGN | GERMANY
161020ronbow.eu | ronbow.comINSTALLATION SHEET
2
See Figure 1.
See Figure 2.
Step 1: Determine the ideal location of your
new LED mirror.
Mark the locations for the long screws
to hang the wall cleat.
NOTE: It is highly recommended
the location has at least two studs.
Front notch the studs to install a 2x4
horizontal beam for added stability.
Figure 1.
Step 2: Cut an opening in the wall and connect
the electrical wires to the housing.
NOTE: Run electrical wires to
the opening. An electrical box is
recommended inside the opening.
Figure 2.
Step 3: Install the reflector to the top of the
mirror cabinet.
INSTALLATION
2X4

UNITY LED Mirror Cabinet
Model : E045612
E045614
Designed By: KURZ KURZ DESIGN | GERMANY
161020ronbow.eu | ronbow.comINSTALLATION SHEET
3
Figure 3.
Figure 4.
Figure 5.
Step 5:
Step 6:
Connect the wires to the electrical box.
Carefully lift and place the mirror
cabinet on the wall cleat.
Verify the cabinet is level.
See Figure 3.
See Figure 4.
See Figure 5.
Step 4: Fasten the wall cleat to the wall using
the 4 long screws.

UNITY LED Mirror Cabinet
Model : E045612
E045614
Designed By: KURZ KURZ DESIGN | GERMANY
161020ronbow.eu | ronbow.comINSTALLATION SHEET
4
Figure 6.
Locate the screw nearest the hinge
cup and rotate clockwise or counter-
clockwise to move the door from side
to side.
Locate the screw furthest away from
the hinge cup and turn the screw
clockwise or counter-clockwise to
move the door from front to back.
Locate the screw pictured in Figure 6.
Turn the screw clockwise or counter-
clockwise to move the door from top
to bottom.
ADJUST DOOR HINGE
Figure 7.
Figure 8.
NOTE: When adjusting the door hinges keep in mind
to adjust the other hinges.
Side to Side
Front to Back
Top to Bottom
See Figure 6.
See Figure 7.
See Figure 8.
Side
Depth
Height

UNITY LED Mirror Cabinet
Model : E045612
E045614
Designed By: KURZ KURZ DESIGN | GERMANY
161020ronbow.eu | ronbow.comINSTALLATION SHEET
5
Wood Surfaces
Recommended Products
The fine furniture finish of your new vanity, mirror or other bathroom accessories are designed to
protect against normal home use. With proper care, your product will provide years of use and beauty
in your home.
General Care Tips
PRODUCT CARE AND MAINTENANCE
• If a spill occurs, clean and dry the surface immediately as liquid can soak through the surface and cause
greater damage.
• Do not place in direct sunlight. Exposure to sunlight may affect the appearance of your vanity, and the
finish will eventually crack.
• Keep away from direct sources of extreme temperatures as heat, cold or moisture from humidity.
Color changes, or blemishes in the wood can occur if recommended care of is not met. Try to avoid
these extremes.
• Most wood surfaces can be cleaned, or dusted, with any commercial wood cleaning product. For general
cleaning, use a non-abrasive, or lint-free cloth while dusting along the wood grain to preserve the
wood’s chacteristics.
• Pledge Orange Oil, or similar
• Orange-Glo Wood Cleaner
DISCLAIMERS: Wood naturally ages, darkens and changes color over time due to several environmental conditions that may cause materials to vary from their
original color and/or to warp, split or crack. These variations are considered to be the nature of the material in relation to their environmental exposure and may
be significant over a long period of time. The eectiveness of cleaning Ronbow product is dependant on various factors that include sunlight, smoke, moisture,
household cleaners and/or amount of cleaning product used over time. Ronbow cannot guarantee that the above Product Care & Maintenance methods will
eectively clean your product.
• Test cleaning product on small, discrete area prior to applying to entire surface.
• Wipe surfaces frequently with dry, soft, non-abrasive and lint-free towel.
• Do not allow liquids and moisture to accumulate on the surface of products.
• For warranty information, please visit our website at www.ronbow.com or contact the Customer Service
Department at [phone].

UNITY LED Mirror Cabinet
Model : E045612
E045614
Designed By: KURZ KURZ DESIGN | GERMANY
161020ronbow.eu | ronbow.comINSTALLATION SHEET
6
Glass Surfaces
• Clean up any spills or liquids immediately. Never allow liquids of any kind to remain on surface as it may
form buildup and deposits.
• DO NOT use abrasive brushes, sponges or cleaners as they may scratch and damage the surface.
• Do not use ol or any oil-based cleaners on the glass as this may remove the frosted finish.
DISCLAIMERS: Clear glass will tend to have a greenish tint. This is a natural feature and not a defect. Eectiveness of cleaning your Ronbow products is dependent
on various factors that include: water temperature, concentration and/or amounts of cleansers. Because of these many dierent conditions, Ronbow cannot
guarantee that the above Product Care & Maintanence methods will eectively clean your product.

161020
40650 Encyclopedia Circle
Fremont, CA 94538
T 510.713.1188
F 510.657.9388 ronbow.eu | ronbow.com