Ronbow Signature series Assembly instructions

INSTALLATION AND CARE GUIDE
71” STACK SIDE CABINET
E016117

160825ronbow.eu | ronbow.comINSTALLATION SHEET
1
Stack 71” Side Cabinet
Model : E016117 Designed By: PHOENIX DESIGN | GERMANY
Tools Required
PRE-INSTALLATION
Materials Included
1 pair of anti-tipping hardware
2 ceramic trays
2 ceramic cups
4 allen screws
1 allen wrench
4 short screws
1 set of stainless steel legs
See Figure 1.
Carefully lay the cabinet on its back.
Install the stainless steel legs using the
allen wrench and 3 allen screws for
each leg.
NOTE: Metal leg levelers are attached
to the legs. Adjust if necessary.
Step 1:
INSTALLATION
Figure 1.
NOTE: For safety reasons it is highly recommended,
but not required to install the anti-tip hardware.

160825ronbow.eu | ronbow.comINSTALLATION SHEET
2
Stack 71” Side Cabinet
Model : E016117 Designed By: PHOENIX DESIGN | GERMANY
Figure 2.
Figure 3.
Measure the distances for the anti-
tipping hardware.
Drill pilot holes before fastening the
hardware.
Zip tie the anti-tipping hardware
together.
Adjust the leg levelers if needed.
Place each of the ceramic cups and
trays inside the cabinet.
See Figure 2.
See Figure 3.
Step 1:
Step 2:
Step 3:
Step 4:
INSTALLING ANTI-TIPPING HARDWARE
Y =
Y =
X =
X =
12
Leveler

160825ronbow.eu | ronbow.comINSTALLATION SHEET
3
Stack 71” Side Cabinet
Model : E016117 Designed By: PHOENIX DESIGN | GERMANY
Figure 4.
Locate the screw nearest the hinge
cup and rotate clockwise or counter-
clockwise to move the door from side
to side.
Locate the screw furthest away from
the hinge cup and turn the screw
clockwise or counter-clockwise to
move the door from front to back.
Locate the screw pictured in Figure 6.
Turn the screw clockwise or counter-
clockwise to move the door from top
to bottom.
ADJUST DOOR HINGE
Figure 5.
Figure 6.
NOTE: When adjusting the door hinges keep in mind
to adjust the other hinges.
Side to Side
Front to Back
Top to Bottom
See Figure 4.
See Figure 5.
See Figure 6.
Side
Depth
Height

160825ronbow.eu | ronbow.comINSTALLATION SHEET
4
Stack 71” Side Cabinet
Model : E016117 Designed By: PHOENIX DESIGN | GERMANY
Figure 7.
Step 2: Slide and lift up the drawer box.
Pull the release latches located
underneath the drawer.
Slide drawer box in until secured by rail
hook.
See Figure 8.
See Figure 7.
See Figure 9.
Step 1:
Step 1:
REMOVE DRAWER
REINSTALL DRAWER
Figure 8.
Figure 9.
Hook
https://youtu.be/4DdK3cj3sTU

160825ronbow.eu | ronbow.comINSTALLATION SHEET
5
Stack 71” Side Cabinet
Model : E016117 Designed By: PHOENIX DESIGN | GERMANY
Wood Surfaces
Recommended Products
The fine furniture finish of your new vanity, mirror or other bathroom accessories are designed to
protect against normal home use. With proper care, your product will provide years of use and beauty
in your home.
General Care Tips
PRODUCT CARE AND MAINTENANCE
• If a spill occurs, clean and dry the surface immediately as liquid can soak through the surface and cause
greater damage.
• Do not place in direct sunlight. Exposure to sunlight may affect the appearance of your vanity, and the
finish will eventually crack.
• Keep away from direct sources of extreme temperatures as heat, cold or moisture from humidity.
Color changes, or blemishes in the wood can occur if recommended care of is not met. Try to avoid
these extremes.
• Most wood surfaces can be cleaned, or dusted, with any commercial wood cleaning product. For general
cleaning, use a non-abrasive, or lint-free cloth while dusting along the wood grain to preserve the
wood’s chacteristics.
• Pledge Orange Oil, or similar
• Orange-Glo Wood Cleaner
DISCLAIMERS: Wood naturally ages, darkens and changes color over time due to several environmental conditions that may cause materials to vary from their
original color and/or to warp, split or crack. These variations are considered to be the nature of the material in relation to their environmental exposure and may
be significant over a long period of time. The eectiveness of cleaning Ronbow product is dependant on various factors that include sunlight, smoke, moisture,
household cleaners and/or amount of cleaning product used over time. Ronbow cannot guarantee that the above Product Care & Maintenance methods will
eectively clean your product.
• Test cleaning product on small, discrete area prior to applying to entire surface.
• Wipe surfaces frequently with dry, soft, non-abrasive and lint-free towel.
• Do not allow liquids and moisture to accumulate on the surface of products.
• For warranty information, please visit our website at www.ronbow.com or contact the Customer Service
Department at [phone].

160825
40650 Encyclopedia Circle
Fremont, CA 94538
T 510.713.1188
F 510.657.9388 ronbow.eu | ronbow.com