Ropeflex ORYX RX2100 OX2 Installation guide

ORYX –RX2100 OX2 & OX2O
Assembly Instructions & Manual
DOC: 32-1015
Configuration subject to change
PLEASE REGISTER YOUR NEW PRODUCT
To register your product online please go to:
www.hipeq.com/product-registration
Product serial number is located on equipment or is shown in the box below
SERIAL NUMBER
If serial number is not sown
please check equipment

O X 2 & O X 2 O A S S E M B L Y I N S T R U C T I O N S & M A N U A L 32- 1 0 1 5 R E V . B
2
WARNING DECAL PLACEMENT
The decals shown here have been placed on
the equipment in indicated locations. If any of
the decals aremissing orillegible, call ustoll-
free at 650.549.5888, Monday through Friday,
9 a.m. until 5 p.m. PacificTime, toorder
replacement decals. Applyreplacement decals
in the locations shown.

O X 2 & O X 2 O A S S E M B L Y I N S T R U C T I O N S & M A N U A L 32- 1 0 1 5 R E V . B
3
IMPORTANT PRECAUTIONS
WARNING: To reduce the risk of serious injury, read the following important precautions
before using this equipment.
1. Read all instructions in this manual and
assemble as described before using this
equipment.
2. It is the responsibility of the owner to
ensure
that all users of this equipment are
adequately informed of all precautions.
3. Use this equipment only on a level surface.
Cover the floor beneath to protect the
surface.
4. Keep children under 12 and pets away from
the equipment at all times.
5. Make sure all parts are properly tightened
each time you use this machine. Replace
any worn parts immediately.
6. Make sure the adjustment knobs are fully
engaged / disengaged before using the
equipment.
7. Always wear athletic shoes for foot
protection while exercising.
8. This equipment is designed to support a
maximum user weight of 300 pounds.
9. Pull on one the rope only and never grab a
rope in a way that prevents the drum from
rotating. Never attempt to hang on the rope
or frame. Pull rope with hands only.
10. If you feel pain or dizziness at any time
while exercising, stop immediately and
begin cooling down.
WARNING: Before beginning this or any exercise program, consult your physician. This is
especially important for persons over the age of 35 or persons with pre-existing health problems.
Read all instructions before using. HiPEQ assumes no responsibility for personal injury or
property damage sustained by or through the use of this product.

O X 2 & O X 2 O A S S E M B L Y I N S T R U C T I O N S & M A N U A L 32- 1 0 1 5 R E V . B
4
Box Contents / Parts List
MAINDRUMASSEMBLY
ITEM
QUANTITY
DESCRIPTION
1
1
OXII Drum with Rope
2
1
OXII Bracket Plate
3
4
Hex Bolt ½-13” x 5.5”
4
8
Washer ½”
5
4
Hex Lock Nut ½-13”
Qty.4
Hex Bolt ½-13” x 5.5”
Qty.8
Washer 1/2"
Qty.4
Lock-nut ½-13"

O X 2 & O X 2 O A S S E M B L Y I N S T R U C T I O N S & M A N U A L 32- 1 0 1 5 R E V . B
5
Tools Required for Assembly
3/4 Hex Socket Ratchet Wrench
3/4 Hex Open Wrench

O X 2 & O X 2 O A S S E M B L Y I N S T R U C T I O N S & M A N U A L 32- 1 0 1 5 R E V . B
6
Product Installation
STEP 1
1-1 With 2 bolts installed as shown adjust the distance between
bracket plates as close to the beam width as possible while allowing the
unit to be mounted.
1-2 If necessary use additional ½” steel washers (not provided) to
ensure that once the bold is tightened it does not touch the rope or
drum.
1-3 Tighten all hardware.
Note: Do not attempt assembly alone. 2 person installation required. Never hang on
the unit or the rope. This will void the warranty and may result in injury or death.
1-1 Adjust gap as described
Use 2 bolt, washers and lock
nuts to secure in place. Once
adjusted in place use remaining
2 bolts with hardware.
1-2 Lock-nut on this side.
Bolt to protrude a
maximum of 1/8” from
top of lock-nut surface
1-2 If necessary use
additional steel washers
on this side

O X 2 & O X 2 O A S S E M B L Y I N S T R U C T I O N S & M A N U A L 32- 1 0 1 5 R E V . B
7
Bracket installation hole pattern

O X 2 & O X 2 O A S S E M B L Y I N S T R U C T I O N S & M A N U A L 32- 1 0 1 5 R E V . B
8
Sample Configuration 1: Indoor

O X 2 & O X 2 O A S S E M B L Y I N S T R U C T I O N S & M A N U A L 32- 1 0 1 5 R E V . B
9
Sample Configuration 2: Outdoor

O X 2 & O X 2 O A S S E M B L Y I N S T R U C T I O N S & M A N U A L 32- 1 0 1 5 R E V . B
10
Equipment Maintenance
WARNING: Routine inspection and maintenance is of critical importance to
ensure maximum safety and performance. We use the highest quality materials
available, but wear is inevitable. Be advised that dangerous conditions can arise
even during a warranty period. A warranty does not negate the owner’s
responsibility to thoroughly, carefully and daily inspect the machine. Consult your
physician before starting your exercise program. For your own safety, do not
begin any exercise program without proper instruction.
1. Check Rope
While the machine is not in use carefully inspect the rope for damage and tears.
Carefully inspect connection of rope ends and make sure that stitching (threads)
are not torn or damaged. Do not use equipment until damaged rope has been
replaced.
2. Upholstery
Wipe down after every workout.
Periodically take the time to use a mild soap or mild vinyl upholstery cleaner.
Avoid using any abrasive cleaner not intended for use on vinyl.
Keep sharp or pointed objects out of your pockets and clear of all upholstery.
3. Nuts/Bolts/Fasteners
Periodically inspect all nuts and bolts. Tighten if needed. If bolts seem to loosen
periodically, use Loctite 242 for a long-term cure.
Go through a re-tightening sequence periodically to ensure that all hardware is
properly tensioned.
4. Adjustments / Locking Pins / Tightening Knobs
Check all pieces for signs of visible wear or damage.
Check springs in Snap Links and Pop Pins for proper tension and alignment.
If the spring sticks or has lost its rigidity, replace it immediately.
5. Anti-Skid Surfaces
Replace if they appear worn or become slippery.
6. Warning Instruction Labels
Inspect and familiarize yourself with all safety warnings and other user
information on decals. Replace decals if damaged, illegible, or removed.

O X 2 & O X 2 O A S S E M B L Y I N S T R U C T I O N S & M A N U A L 32- 1 0 1 5 R E V . B
11
WARRANTY
We strive to offer the simplest and fastest resolution to all product related
concerns. Our warranty service program gives its customers the option to return
the product for repair, exchange or refund if the product is determined to be
defective.
•All products are warranted to the original purchaser.
•Warranties apply and cover all defects in material and workmanship.
Frame (excluding coating): Lifetime
Rope, Sheaves, Bearings and Labor: One-Year
•Customer is responsible for the cost of shipment to HiPEQ. Company
“ship to” address for product returns and service will be provided once the
RMA has been issued. It will be at HIPEQ’s discretion to determine the
party responsible for cost of shipment back to customer.
•Out-of-Warranty Products are repaired only with the customer’s prior
approval.
•15 Day 100% Satisfaction Guarantee includes full refund of purchase
price, less shipping, handling and restocking fee equaling 15% of price
during purchase. Email for more details. If you decide to return a HiPEQ
product, simply email us within 15 days to ask for a return authorization
number (RMA). Items must be returned in original condition and
packaging and postmarked no later than 2 weeks after the date of return
authorization.

12
If you have any questions regarding HIPEQ
equipment or any instruction found in this document,
please call 650.549.5888 for assistance.