Ropeflex ROPERIG Installation guide

ROPERIG | RX8100
Assembly Instructions & Manual
PN: 32-8100
Configuration subject to change

R X 8 1 0 0 A S S E M B L Y I N S T R U C T I O N S & M A N U A L 32- 8 1 0 0 R E V . A
1
WARNING DECAL PLACEMENT
The decals shown herehave been placed on
the equipment. If any ofthe decals aremissing
orillegible, call ustoll-free at 650.549.5888,
Mondaythrough Friday, 9 a.m. until5 p.m.
Pacific Time, to order replacement decals.
Apply replacement decals where theyhave
been placed originally.

R X 8 1 0 0 A S S E M B L Y I N S T R U C T I O N S & M A N U A L 32- 8 1 0 0 R E V . A
2
IMPORTANT PRECAUTIONS
WARNING: To reduce the risk of serious injury, read the following important precautions before
using this equipment.
1. Read all instructions in this manual and
assemble as described before using this
equipment.
2. It is the responsibility of the owner to ensure
that all users of this equipment are are
adequately informed of all precautions.
3. Use this equipment only on a level surface.
Cover the floor beneath to protect the
surface.
4. Keep children under 12 and pets away from
the equipment at all times.
5. Make sure all parts are properly tightened
each time you use this machine. Replace
any worn parts immediately.
6. Make sure the adjustment knobs are fully
engaged / disengaged before using the
equipment.
7. Always wear athletic shoes for foot
protection while exercising.
8. This equipment is designed to support a
maximum user weight of 300 pounds.
9. Pull on one the rope only and never grab a
rope in a way that prevents the drum from
rotating. Never attempt to hang on the rope
or frame. Pull rope with hands only.
10. If you feel pain or dizziness at any time
while exercising, stop immediately and
begin cooling down.
WARNING: Before beginning this or any exercise program, consult your physician. This is
especially important for persons over the age of 35 or persons with pre-existing health problems.
Read all instructions before using. HIPEQ assumes no responsibility for personal injury or property
damage sustained by or through the use of this product.

R X 8 1 0 0 A S S E M B L Y I N S T R U C T I O N S & M A N U A L 32- 8 1 0 0 R E V . A
3
MAIN FRAME ASSEMBLY | 12 RX2100 CONFIGURATION
MAIN COMPONENTS
ITEM
QUANTITY
DESCRIPTION
1
4
Vertical RIG Beam
2
4
Horizontal RIG Beam
3
12
LCD Display Extension Clamping Plate (For the RX2100)
4
2
Logo Display
5
12
RX2100Rope Trainer
3
1
2
4
4
5

R X 8 1 0 0 A S S E M B L Y I N S T R U C T I O N S & M A N U A L 32- 8 1 0 0 R E V . A
4
RECOMMENDED TOOLS
RatchetWrench, 3/8" Square Drive
3/8" SquareDrive FlexSocketAdapter
1/4 in. x 3/8 in. SteelSquareSocket Adapter
Hex Bit Socket
3/8" Square Drive, 3/8" Size, 2-3/4" Long
6-Point StandardSocket, 3/8" Drive, 3/4" Size
Ball-End Hex Key, 3/8”
Ball-End Hex Key, ¼”
¾” Combination Wrench
Screwdriver,#2Phillips
Soft Rubber Hammer
Torque driver, 3/8” Square Drive
Cordless Impact Driver

R X 8 1 0 0 A S S E M B L Y I N S T R U C T I O N S & M A N U A L 32- 8 1 0 0 R E V . A
5
HARDWARE
ITEM
QUANTITY
DESCRIPTION
1
32
Zinc-Plated Alloy Steel Socket Head Screw
1/2"-13 ThreadSize, 1" Long
TORQUE: lubricated 55 ft-lb
2
6
Alloy Steel Socket HeadScrew
5/16"-18 Thread Size, 2" Long, Partially Threaded
3
6
AluminumUnthreaded Spacer
3/4" OD, 1-1/4" Long, for 5/16" Screw Size
4
48
Alloy Steel Socket HeadScrew 1/2"-13 Thread
Size, 5" Long
5
48
Steel Nylon-Insert FlangeLocknut, Zinc-Plated,
1/2"-13 ThreadSize
6
56
SSWasher .515" ID,.875" OD
7
6
SS WASHER 5/16", .344x.75x.05"

R X 8 1 0 0 A S S E M B L Y I N S T R U C T I O N S & M A N U A L 32- 8 1 0 0 R E V . A
6
ASSEMBLY | STEP 1
1. AssembleRIG as shown following assembly photos
2. Connect RIG members using Item 1 (hardware table)
3. Torque as specified

R X 8 1 0 0 A S S E M B L Y I N S T R U C T I O N S & M A N U A L 32- 8 1 0 0 R E V . A
7
ASSEMBLY | STEP 2
1. Using Item 3 –LCD Display Extension Clamping Plate (main components table), install
RX2100Rope trainers as shown,spacing themequally.
2. Torque as specified
3. Connect 3.5mm sensor cablefrom eachRX2100 unit to the corresponding LCD display
cablecomingfrom top of Item3
DISPLAY VERIFICATION
1. Pullthe rope allRX2100 toverify that display turns on and is counting
2. Toreset display open the enclosure (4 screws on the front) and located theRED button.
Long pressing RED buttons will reset the counter
3. Reassemble LCD enclosure ensuring that it sits properly in order toseal it properly

R X 8 1 0 0 A S S E M B L Y I N S T R U C T I O N S & M A N U A L 32- 8 1 0 0 R E V . A
8
ASSEMBLY | STEP 3
1. Attach Logo Plates Item 4 (component table) as shown, using Items 2, 3 & 7 (hardware
table).
2. Note: it is important to makesure thatthehorizontal beams are placed properly in
ASSEMBLYSTEP1, to makesure that LogoPlates threadedholes arefacing up, and
areon oppositeends as shown.
4
4

9
If you have any questions regarding HiPEQ
equipment or any instruction found in this document,
please call 650.549.5888 for assistance.
HIPEQ CORP.