ROSE DISPLAYS SUPERSNAP WITH CABLE CLIP AND BALL CHAIN User manual

35 Congress Street, Salem, MA 01970
Tel# [phone] Fax# [phone]
e-mail:[e-mail]
Parts
SuperSnap™
Step 1
Snap the SuperSnap open and insert poster
(top and bottom). Fig. 1
Note: It is easier to open and close the
SuperSnap by starting at one end and work-
ing your way down the holder.
To close, snap the SuperSnap shut.
Fig. 2
Step 2
Insert single ball of ball chain into inner
channel of Cable Clip. The cable should
snap into place. Fig. 3
Step 3
Align one round end of cable clip with top
channel of the rail and insert. Once in place,
insert end of ball chain into channel. Then
press down on the other round end of the
cable clip and slide into rail by pushing on
the clip. Fig. 4 Repeat steps 2 & 3 for second
cable clip.
Note: Be sure to push on the cable clip in
order to slide the ball chain into place. Do
not pull on, or push against, the ball chain
as this will cause it to bind in the channel.
Step 4
Push end caps into place. Fig 5
Suspend poster. Finished Look
Important note:
Please save and reuse the
SuperSnap, End Caps and
Cable Clips for future projects.
Instruction Sheet
Instructions for assembly
Incept-11.13.02
The SuperSnap™ is a trademark of Rose Displays, Ltd. Neither the
manufacturer nor any sales agent may be held liable for injury, loss or
damage resulting from the use of these products.
Part #02INSSuperSnapCCBC
Figure 2
Figure 5
Figure 3
Figure 1
Finished Look
Figure 4
Cable Clip
06-5050
SuperSnap
12S300
End Caps
06-5475
Ball Chains
96-0302P

35 Congress Street, Salem, MA 01970
Tel# [phone] Fax# [phone]
e-mail:[e-mail]
Parts
SuperSnap™ Instruction Sheet
Instructions for assembly
Incept-11.13.02
The SuperSnap™ is a trademark of Rose Displays, Ltd. Neither the
manufacturer nor any sales agent may be held liable for injury, loss or
damage resulting from the use of these products.
Part #02INSSuperSnapCCBC
Figure 2
Figure 5
Figure 3
Figure 1
Finished Look
Figure 4
Cable Clip
06-5050
SuperSnap
12S300
End Caps
06-5475
Ball Chain
96-0302P
Step 1
Snap the SuperSnap open and insert poster
(top and bottom). Fig. 1
Note: It is easier to open and close the
SuperSnap by starting at one end and work-
ing your way down the holder.
To close, snap the SuperSnap shut.
Fig. 2
Step 2
Insert single ball of ball chain into inner
channel of Cable Clip. The cable should
snap into place. Fig. 3
Step 3
Align one round end of cable clip with top
channel of the rail and insert. Once in place,
insert end of ball chain into channel. Then
press down on the other round end of the
cable clip and slide into rail by pushing on
the clip. Fig. 4
Note: Be sure to push on the cable clip in
order to slide the ball chain into place. Do
not pull on, or push against, the ball chain
as this will cause it to bind in the channel.
Step 4
Push end caps into place. Fig 5
Suspend poster. Finished Look
Important note:
Please save and reuse the
SuperSnap, End Caps and
Cable Clips for future projects.

Parts
SuperSnap™ Instruction Sheet
Instructions for assembly
Incept-11.13.02
The SuperSnap™ is a trademark of Rose Displays, Ltd. Neither the
manufacturer nor any sales agent may be held liable for injury, loss or
damage resulting from the use of these products.
Part #02INSSuperSnapCCBC
Figure 2
Figure 5
Figure 3
Figure 1
Finished Look
Figure 4
Cable Clips
06-5050
SuperSnap
12S300
End Caps
06-5475
Ball Chains
96-0302P
Step 1
Snap the SuperSnap open and insert poster
(top and bottom). Fig. 1
Note: It is easier to open and close the
SuperSnap by starting at one end and work-
ing your way down the holder.
To close, snap the SuperSnap shut.
Fig. 2
Step 2
Insert single ball of ball chain into inner
channel of Cable Clip. The cable should
snap into place. Fig. 3
Step 3
Align one round end of cable clip with top
channel of the rail and insert. Once in place,
insert end of ball chain into channel. Then
press down on the other round end of the
cable clip and slide into rail by pushing on
the clip. Fig. 4 Repeat steps 2 & 3 for second
cable clip.
Note: Be sure to push on the cable clip in
order to slide the ball chain into place. Do
not pull on, or push against, the ball chain
as this will cause it to bind in the channel.
Step 4
Push end caps into place. Fig 5
Suspend poster. Finished Look
Important note:
Please save and reuse the
SuperSnap, End Caps and
Cable Clips for future projects.

Parts
Cable Clip
06-5050
SuperSnap
12S300
SuperSnap™ Instruction Sheet
Instructions for assembly
Incept-11.13.02
The SuperSnap™ is a trademark of Rose Displays, Ltd. Neither the
manufacturer nor any sales agent may be held liable for injury, loss or
damage resulting from the use of these products.
Part #02INSSuperSnapCCBC
Figure 2
Figure 5
Figure 3
Figure 1
Finished Look
Figure 4
End Caps
06-5475
Ball Chain
96-0302P
Step 1
Snap the SuperSnap open and insert poster
(top and bottom). Fig. 1
Note: It is easier to open and close the
SuperSnap by starting at one end and work-
ing your way down the holder.
To close, snap the SuperSnap shut.
Fig. 2
Step 2
Insert single ball of ball chain into inner
channel of Cable Clip. The cable should
snap into place. Fig. 3
Step 3
Align one round end of cable clip with top
channel of the rail and insert. Once in place,
insert end of ball chain into channel. Then
press down on the other round end of the
cable clip and slide into rail by pushing on
the clip. Fig. 4
Note: Be sure to push on the cable clip in
order to slide the ball chain into place. Do
not pull on, or push against, the ball chain
as this will cause it to bind in the channel.
Step 4
Push end caps into place. Fig 5
Suspend poster. Finished Look
Important note:
Please save and reuse the
SuperSnap, End Caps and
Cable Clips for future projects.