Rosemount 3144P User manual

Quick Start Guide
00825-0100-4834, Rev DA
June 2016
Rosemount™3144P Temperature
Transmitters
with FOUNDATION™Fieldbus Protocol

June 2016
2
Quick Start Guide
NOTICE
This guide provides basic guidelines for Rosemount 3144P. It does not provide instructions for
configuration, diagnostics, maintenance, service, troubleshooting or intrinsically safe (I.S.) installations.
Refer to the Rosemount 3144P Reference Manual for more instruction. The manual and this guide are also
available electronically on EmersonProcess.com/Rosemount.
Explosions could result in death or serious injury.
Installation of this transmitter in an explosive environment must be in accordance with the
appropriate local, national, and international standards, codes, and practices. Review the
approvals section of this manual for any restrictions associated with a safe installation.
In an Explosion-proof/Flameproof installation, do not remove the transmitter covers when power
is applied to the unit.
Process leaks may cause harm or result in death.
Install and tighten thermowells or sensors before applying pressure.
Do not remove the thermowell while in operation.
Electrical shock can result in death or serious injury.
Avoid contact with the leads and terminals. High voltage that may be present on leads can cause
electrical shock.
Contents
Mount the transmitter . . . . . . . . . . . . . . . . . . . . 3
Wire and apply power . . . . . . . . . . . . . . . . . . . . . 4
Verify tagging . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Verify transmitter configuration . . . . . . . . . . . . 9
Set the switches . . . . . . . . . . . . . . . . . . . . . . . . . 10
Product Certifications . . . . . . . . . . . . . . . . . . . . 12

Quick Start Guide
3
June 2016
1.0 Mount the transmitter
Mount the transmitter at a high point in the conduit run to prevent moisture from
draining into the transmitter housing.
1.1 Typical North America installation
1. Mount the thermowell to the process container wall. Install and tighten
thermowells. Perform a leak check.
2. Attach any necessary unions, couplings, and extension fittings. Seal the fitting
threads with an approved thread sealant, such as silicone or PTFE tape (if
required).
3. Screw the sensor into the thermowell or directly into the process (depending
on installation requirements).
4. Verify all sealing requirements.
5. Attach the transmitter to the thermowell/sensor assembly. Seal all threads
with an approved thread sealant, such as silicone or PTFE tape (if required).
6. Install field wiring conduit into the open transmitter conduit entry (for remote
mounting) and feed wires into the transmitter housing.
7. Pull the field wiring leads into the terminal side of the housing.
8. Attach the sensor leads to the transmitter sensor terminals (the wiring
diagram is located inside the housing cover).
9. Attach and tighten both transmitter covers.
1.2 Typical European installation
1. Mount the thermowell to the process container wall. Install and tighten
thermowells. Perform a leak check.
2. Attach a connection head to the thermowell.
3. Insert sensor into the thermowell and wire the sensor to the connection head
(the wiring diagram is located inside the connection head).
4. Mount the transmitter to a 2-in. (50 mm) pipe or a panel using one of the
optional mounting bracket (B4 bracket is shown below).
5. Attach cable glands to the shielded cable running from the connection head
to the transmitter conduit entry.
A. Thermowell D. Conduit for field wiring (dc power)
B. Extension (Nipple) E. Extension fitting length
C. Union or Coupling
ABC
ED

June 2016
4
Quick Start Guide
6. Run the shielded cable from the opposite conduit entry on the transmitter
back to the control room.
7. Insert shielded cable leads through the cable entries into the connection
head/transmitter. Connect and tighten cable glands.
8. Connect the shielded cable leads to the connection head terminals (located
inside the connection head) and to the sensor wiring terminals (located inside
the transmitter housing).
2.0 Wire and apply power
Connect the transmitter to a FOUNDATION Fieldbus network. Two terminators and
a power conditioner are required. The voltage at the transmitter terminals must
be between 9 and 32 Vdc to operate properly.
2.1 Power filter
A fieldbus segment requires a power conditioner to isolate the power supply and
decouple the segment from other segments attached to the same power supply.
2.2 Power the transmitter
1. Remove the terminal block cover.
2. Connect power to the power terminal. The terminals are polarity insensitive.
3. Tighten the terminal screws.
4. Reattach and tighten the cover.
5. Apply power.
A. Cable gland
B. Shielded cable from sensor to transmitter
C. Shielded cable from transmitter to control room
D. 2-in. (50 mm) pipe
E. B4 mounting bracket
A
B
C
D
E

Quick Start Guide
5
June 2016
Figure 1. Power the Transmitter
A. Sensor terminals (1–5)
B. Power terminals
C. Ground
2.3 Wiring diagram
Figure 2. Rosemount 3144P Single-Sensor
Figure 3. Rosemount 3144P Dual-Sensor
1. Emerson™Process Management provides 4-wire sensors for all single-element RTDs. You can use
these RTDs in 3-wire configurations by leaving the unneeded leads disconnected and insulated with
electrical tape.
2. Transmitter must be configured for a 3-wire RTD in order to recognize an RTD with a compensation
loop.
1. Emerson provides 4-wire sensors for all single-element RTDs. You can use these RTDs in 3-wire
configurations by leaving the unneeded leads disconnected and insulated with electrical tape.
A
C
B
4-wire RTD
and Ohms
T/Cs and
Millivolts
RTD with
Compensation
Loop(2)
2-wire RTD
and Ohms
3-wire RTD
and Ohms(1)
ΔT/Hot
Backup/Dual
Sensor with 2
RTDs(1)
ΔT/Hot
Backup/Dual
Sensor with 2
Thermocouples
ΔT/Hot
Backup/Dual
Sensor with RTDs/
Thermocouples(1)
ΔT/Hot
Backup/Dual
Sensor with RTDs/
Thermocouples(1)
ΔT/
Hot Backup/Dual
Sensor with 2 RTDs with
Compensation Loop(1)

June 2016
6
Quick Start Guide
Figure 4. Typical Configuration for FOUNDATION Fieldbus Networking
Note
Each segment in a Fieldbus trunk must be terminated at both ends.
2.4 Ground the transmitter
Ungrounded thermocouple, mV, and RTD/Ohm inputs
Each process installation has different requirements for grounding. Use the
grounding options recommended by the facility for the specific sensor type, or
begin with grounding Option 1 (the most common).
Option 1 (recommended for ungrounded transmitter housing)
1. Connect signal wiring shield to the sensor wiring shield.
2. Ensure the two shields are tied together and electrically isolated from the
transmitter housing and other grounded fixtures.
3. Ground shield at the power supply end only.
4. Ensure the sensor shield is electrically isolated from the surrounding
grounded fixtures.
A. 6234 ft. (1900 m) max
(depending upon cable characteristics)
B. Integrated power conditioner and filter
C. Terminators
D. Power supply
E. Trunk
F. Spur
G. FOUNDATION Fieldbus configuration tool
H. Power/signal wiring
I. Devices 1 through 16
J. The power supply, filter, first terminator,
and configuration tool are typically located
in the control room.
A
BC
E
F
D
G
J
H
I

Quick Start Guide
7
June 2016
5. Connect shields together, electrically isolated from the transmitter.
Option 2 (recommended for grounded transmitter housing)
1. Connect sensor wiring shield to the transmitter housing (only if the housing is
grounded).
2. Ensure the sensor shield is electrically isolated from the transmitter housing
and other grounded fixtures.
3. Ground signal wiring shield at the power supply end.
Option 3
1. Ground sensor wiring shield at the sensor, if possible.
2. Ensure the sensor wiring and signal wiring shields are electrically isolated from
the transmitter housing and other grounded fixtures.
3. Ground signal wiring shield at the power supply end.
Grounded thermocouple inputs
1. Ground sensor wiring shield at the sensor.
2. Ensure the sensor wiring and signal wiring shields are electrically isolated from
the transmitter housing and other grounded fixtures.
A. Sensor wire
B. Transmitter
C. Shield ground point
A. Sensor wire
B. Transmitter
C. Shield ground point
A. Sensor wire
B. Transmitter
C. Shield ground point
C
B
A
A
B
C
A
B
C

June 2016
8
Quick Start Guide
3. Ground signal wiring shield at the power supply end.
3.0 Verify tagging
3.1 Commissioning (paper) tag
To identify which device is at a particular location use the removable tag provided with
the transmitter. Ensure the physical device tag (PD Tag field) is properly entered in both
places on the removable commissioning tag and tear off the bottom portion for each
transmitter.
Figure 5. Commissioning (Paper) Tag
Note
The device description loaded in the host system must be at the same revision as this device. The
device description can be downloaded from EmersonProcess.com/Rosemount.
A. Sensor wire
B. Transmitter
C. Shield ground point
A
B
C
COMMISSIONING TAG
Device ID:
0011513144-FR-TEMP-0X472D2402
PD Tag:
TT- 101
Revision:
Device ID:
0011513144-FR-TEMP-0X472D2402
PD Tag:
TT- 101
Revision:
Tear Here

Quick Start Guide
9
June 2016
Verify transmitter configuration
Each FOUNDATION Fieldbus host or configuration tool has a different way of
displaying and performing configurations. Some use Device Descriptions (DD) or
DD methods for configuration and to display data consistently across platforms.
There is no requirement that a host or configuration tool support these features.
The following is the minimum configuration requirement for a temperature
measurement. This guide is designed for systems not using DD methods. For a
complete list of parameters and configuration information refer to the
Rosemount 3144P Temperature Transmitter Reference Manual.
3.2 Transducer function block
This block contains temperature measurement data for the sensors and the
terminal temperature. It also includes information about sensor types,
engineering units, damping, and diagnostics. At a minimum, verify the
parameters in Table 1.
Analog Input (AI) function block
The AI block processes field device measurements and makes the outputs
available to other function blocks. The output value of the AI block is in
engineering units and contains a status indicating the quality of the
measurements. Use the Channel number to define the variable that the AI block
processes. At a minimum, verify the parameters of each AI block in Table 2.
Note
All devices ship with the AI blocks scheduled, meaning no configuration is needed if the factory
default channels are used.
Table 1. Transducer Block Parameters
Parameter Comments
Typical configuration
SENSOR_TYPE_X example: “Pt 100_A_385 (IEC 751)”
SENSOR_CONNECTIONS_X example: “2-wire”, “3-wire”, “4-wire”
Sensor matching configuration
SENSOR_TYPE_X “User Defined, Calvandu”
SENSOR_CONNECTIONS_X example: “2-wire”, “3-wire”, “4-wire”
SENSOR_CAL_METHOD_X set to “User Trim Standard”
SPECIAL_SENSOR_A_X enter sensor specific coefficients
SPECIAL_SENSOR_B_X enter sensor specific coefficients
SPECIAL_SENSOR_C_X enter sensor specific coefficients
SPECIAL_SENSOR_R0_X enter sensor specific coefficients

June 2016
10
Quick Start Guide
Note
To make changes to the AI block, the BLOCK_MODE (TARGET) must be set to OOS (out of service).
Once the changes are made, return the BLOCK_MODE TARGET to AUTO.
Set the switches
The security and simulate switches are located on the top center of the
electronics module. Follow the steps below to set the switches.
Note
The simulate switch is shipped in the “ON” position from the factory.
Table 2. AI Block Parameters(1)
1. Configure one AI Block for each desired measurement.
Parameter Comments
CHANNEL
Choices:
1. Sensor 1 Temperature
2. Sensor 2 Temperature
3. Differential Temperature
4. Terminal Temperature
5. Sensor 1 Min. Value
6. Sensor 1 Max Value
7. Sensor 2 Min. Value
8. Sensor 2 Max Value
9. Differential Min. Value
10. Differential Max Value
11. Terminal Temp Min. Value
12. Terminal Temp Max Value
13. Hot Backup
L_TYPE For most measurements, set to “DIRECT”
XD_SCALE
Set desired measurement range and units. Units must be one of the
following:
mV
Ohms
°C
°F
°R
K
OUT_SCALE For “DIRECT” L_TYPE, set OUT_SCALE to match XD_SCALE
HIGH_HIGH_LIM
HIGH_LIM
LOW_LIM
LOW_LOW_LIM
Process alarms.
Must be within the range defined by “OUT_SCALE.”

Quick Start Guide
11
June 2016
3.3 Without a LCD display
1. Set the loop to Out-of-Service (OOS) mode (if applicable) and disconnect the
power.
2. Remove the electronics housing cover.
3. Set the switches to the desired position. Reattach housing cover.
4. Apply power and set the loop to In-Service mode.
3.4 With a LCD display
1. Set the loop to Out-of-Service (OOS) (if applicable) and disconnect the power.
2. Remove the electronics housing cover.
3. Unscrew the LCD display meter screws and pull the meter straight off.
4. Set the switches to the desired position. The simulate switch is default set to
the “ON” position.
5. Reattach the LCD display meter and electronics housing cover (consider LCD
display meter orientation).
6. Apply power and set the loop to In-Service mode.

June 2016
12
Quick Start Guide
4.0 Product Certifications
Rev 1.3
4.1 European Directive Information
A copy of the EC Declaration of Conformity can be found at the end of the Quick
Start Guide. The most recent revision of the EC Declaration of Conformity can be
found at EmersonProcess.com/Rosemount.
4.2 Ordinary Location Certification
As standard, the transmitter has been examined and tested to determine that the
design meets the basic electrical, mechanical, and fire protection requirements
by a nationally recognized test laboratory (NRTL) as accredited by the Federal
Occupational Safety and Health Administration (OSHA).
North America
E5 FM Explosionproof, Dust-Ignitionproof, and Nonincendive
Certificate: 3012752
Standards: FM Class 3600: 1998, FM Class 3611: 2004, FM Class 3615: 1989, FM Class
3810: 2005, NEMA®-250: 1991, ANSI/ISA 60079-0: 2009, ANSI/ISA
60079-11: 2009
Markings: XP CL I, DIV 1, GP A, B, C, D; T5(-50 °C ≤ Ta≤ +85 °C); DIP CL II/III, DIV 1, GP E,
F, G; T5(–50 °C ≤ Ta≤ +75 °C); T6(-50 °C ≤ Ta≤ +60 °C); when installed per
Rosemount drawing 03144-0320; NI CL I, DIV 2, GP A, B, C, D; T5(–60 °C ≤Ta
≤ +75 °C); T6(–60 °C ≤ Ta≤ +50 °C); when installed per Rosemount drawing
03144-0321, 03144-5075
I5 FM Intrinsic Safety and Nonincendive
Certificate: 3012752
Standards: FM Class 3600: 1998, FM Class 3610: 2010, FM Class 3611: 2004, FM Class
3810: 2005, NEMA-250: 1991, ANSI/ISA 60079-0: 2009, ANSI/ISA 60079-11:
2009
Markings: IS CL I/II/III, DIV 1, GP A, B, C, D, E, F, G; T4(–60 °C ≤ Ta≤ +60 °C); IS [Entity]
CL I, Zone 0, AEx ia IIC T4(–60 °C ≤ Ta≤ +60 °C); NI CL I, DIV 2, GP A, B, C, D;
T5(–60 °C ≤Ta≤ +75 °C); T6(–60 °C ≤ Ta≤ +50 °C); when installed per
Rosemount drawing 03144-0321, 03144-5075
I6 CSA Intrinsic Safety and Division 2
Certificate: 1242650
Standards: CAN/CSA C22.2 No. 0-M91 (R2001), CAN/CSA-C22.2 No. 94-M91, CSA Std
C22.2 No. 142-M1987, CAN/CSA-C22.2 No. 157-92, CSA Std C22.2 No.
213-M1987
Markings: Intrinsically Safe for Class I Groups A, B, C, D; Class II, Groups E, F, G; Class III;
[HART®only zone markings]: Intrinsically Safe for Class I Zone 0 Group IIC; T4
(–50 °C ≤Ta≤ +60 °C); Type 4X;Suitable for Class I, Div. 2, Groups A, B, C, D;
[HART only zone markings]: Suitable for Class I Zone 2 Group IIC; T6(–60 °C ≤
Ta≤ +60°C); T5(–60 °C ≤Ta≤ +85 °C); when installed per Rosemount drawing
03144-5076

Quick Start Guide
13
June 2016
K6 CSA Explosionproof, Intrinsic Safety and Division 2
Certificate: 1242650
Standards: CAN/CSA C22.2 No. 0-M91 (R2001), CSA Std C22.2 No. 30-M1986;
CAN/CSA-C22.2 No. 94-M91, CSA Std C22.2 No. 142-M1987,
CAN/CSA-C22.2 No. 157-92, CSA Std C22.2 No. 213-M1987
Markings: Explosionproof for Class I, Groups A, B, C, D; Class II, Groups E, F, G; Class III;
[HART only zone markings]: Suitable for Class I Zone 1 Group IIC; Intrinsically
Safe for Class I Groups A, B, C, D; Class II, Groups E, F, G; Class III
[HART only zone markings]: Suitable for Class I Zone 0 Group IIC; T4 (–50 °C ≤
Ta≤ +60 °C); Type 4X; Suitable for Class I, Div. 2, Groups A, B, C, D
[HART only zone markings]: Suitable for Class I Zone 2 Group IIC; T(–60 °C ≤
Ta≤ +60 °C); T5(–60 °C ≤Ta≤ +85 °C); when installed per Rosemount drawing
03144-5076
Europe
E1 ATEX Flameproof
Certificate: FM12ATEX0065X
Standards: EN 60079-0: 2012, EN 60079-1: 2007, EN 60529:1991 +A1:2000
Markings: II 2 G Ex d IIC T6…T1 Gb, T6(–50 °C ≤Ta≤+40 °C), T5…T1(–50 °C ≤Ta≤
+60 °C)
See Table 3 at the end of the Product Certifications section for process temperatures.
Special Conditions for Safe Use (X):
1. See certificate for ambient temperature range.
2. The non-metallic label may store an electrostatic charge and become a source of
ignition in Group III environments.
3. Guard the LCD display cover against impact energies greater than 4 joules.
4. Consult the manufacturer if dimensional information on the flameproof joints is
necessary.
I1 ATEX Intrinsic Safety
Certificate: BAS01ATEX1431X [HART]; Baseefa03ATEX0708X [Fieldbus];
Standards: EN 60079-0: 2012; EN 60079-11:2012
Markings: HART: II 1 G Ex ia IIC T4 Ga; T4(-60 °C ≤ Ta≤ +60 °C),
Fieldbus: II 1 G Ex ia IIC T4 Ga; T4(-60 °C ≤ Ta≤ +60 °C)
See Table 4 at the end of the Product Certifications section for Entity Parameters.
Special Conditions for Safe Use (X):
1. When fitted with the transient terminal options, the equipment is not capable of
passing the 500 V insulation test. This must be taken into account during installation.
2. The enclosure may be made from aluminum alloy with a protective polyurethane paint
finish; however, care should be taken to protect it from impact or abrasion when located
in Zone 0.
N1 ATEX Type n
Certificate: BAS01ATEX3432X [HART]; Baseefa03ATEX0709X [Fieldbus]
Standards: EN 60079-0:2012, EN 60079-15:2010
Markings: HART: II 3 G Ex nA IIC T5/T6 Gc; T6(-40 °C ≤ Ta≤+50 °C), T5(-40 °C ≤ Ta≤
+75 °C);
Fieldbus: II 3 G Ex nA IIC T5 Gc; T5(-40 °C ≤ Ta≤+75 °C)
Special Condition for Safe Use (X):
1. When fitted with the transient terminal options, the equipment is not capable of
withstanding the 500 V electrical strength test as defined in clause 6.5.1 of EN
60079-15: 2010. This must be taken into account during installation.

June 2016
14
Quick Start Guide
ND ATEX Dust
Certificate: FM12ATEX0065X
Standards: EN 60079-0: 2012, EN 60079-31: 2009, EN 60529:1991 +A1:2000
Markings: II 2 D Ex tb IIIC T130 °C Db, (-40 °C ≤Ta≤ +70 °C); IP66
See Table 3 at the end of the Product Certifications section for process temperatures.
Special Conditions for Safe Use (X):
1. See certificate for ambient temperature range.
2. The non-metallic label may store an electrostatic charge and become a source of
ignition in Group III environments.
3. Guard the LCD display cover against impact energies greater than 4 joules.
4. Consult the manufacturer if dimensional information on the flameproof joints is
necessary.
International
E7 IECEx Flameproof
Certificate: IECEx FMG 12.0022X
Standards: IEC 60079-0:2011, IEC 60079-1:2007-04, IEC 60079-31:2008
Markings: Ex d IIC T6…T1 Gb, T6(-50 °C ≤Ta≤+40 °C), T5…T1(-50 °C ≤ Ta≤+60 °C); Ex
tb IIIC T130 °C Db, (-40 °C ≤Ta≤+70 °C); IP66
See Table 3 at the end of the Product Certifications section for process temperatures.
Special Conditions for Safe Use (X):
1. See certificate for ambient temperature range.
2. The non-metallic label may store an electrostatic charge and become a source of
ignition in Group III environments.
3. Guard the LCD display cover against impact energies greater than 4 joules.
4. Consult the manufacturer if dimensional information on the flameproof joints is
necessary.
I7 IECEx Intrinsic Safety
Certificate: IECEx BAS 07.0002X [HART]; IECEx BAS 07.0004X [Fieldbus]
Standards: IEC 60079-0: 2011; IEC 60079-11: 2011;
Markings: HART: Ex ia IIC T5/T6 Ga; T6(-60 °C ≤Ta≤+50 °C), T5(-60 °C ≤Ta≤+75 °C);
Fieldbus: Ex ia IIC T4 Ga; T4(-60 °C ≤Ta≤ +60 °C)
See Table 4 at the end of the Product Certifications section for entity parameters.
Special Conditions for Safe Use (X):
1. When fitted with the transient terminal options, the apparatus is not capable of
withstanding the 500 V electrical strength test as defined in Clause 6.3.13 of IEC
60079-11: 2011. This must be taken into account during installation.
2. The enclosure may be made from aluminum alloy with a protective polyurethane paint
finish; however, care should be taken to protect it from impact or abrasion when located
in Zone 0.
N7 IECEx Type n
Certificate: IECEx BAS 07.0003X [HART]; IECEx BAS 07.0005X [Fieldbus]
Standards: IEC 60079-0:2011, IEC 60079-15:2010
Markings: HART: Ex nA IIC T5/T6 Gc; T6(-40 °C ≤Ta≤ +50 °C), T5(-40 °C ≤Ta≤+75 °C);
Fieldbus: Ex nA IIC T5 Gc; T5(-40 °C ≤Ta≤+75 °C)

Quick Start Guide
15
June 2016
Brazil
E2 INMETRO Flameproof
Certificate: UL-BR 13.0535X
Standards: ABNT NBR IEC 60079-0:2008 + corrigendum 1:2011,
ABNT NBR IEC 60079-1:2009 + corrigendum 1:2011
Markings: Ex d IIC T6...T1* Gb; T6…T1*: -50 °C ≤Tamb ≤+40 °C; T5...T1*: -50 °C ≤
Tamb ≤ +60 °C
Special Conditions for Safe Use (X):
1. See product description for ambient temperature limits and process temperature limits.
2. The non-metallic label may store an electrostatic charge and become a source of
ignition in Group III environments.
3. Guard the LCD display cover against impact energies greater than 4 joules.
4. Consult the manufacturer if dimensional information on the flameproof joints is
necessary.
I2 INMETRO Intrinsic Safety [HART]
Certificate: UL-BR 15.0088X
Standards: ABNT NBR IEC 60079-0:2008 + corrigendum 1:2011,
ABNT NBR IEC 60079-11:2009
Markings: Ex ia IIC T4 Ga (-60 ° C ≤ Ta≤ +60 °C),
See Table 4 at the end of the Product Certifications section for entity parameters.
Special Conditions for Safe Use (X):
1. When mounted with the terminal options with transient protection, the equipment is
not capable of withstanding the dielectric strength test with 500 V as defined in ISO IEC
60079-11. This feature should be taken into account during installation.
2. The enclosure may be made from aluminum alloy with a protective polyurethane paint
finish; however, care should be taken to protect it from impact and abrasion when
located in areas that require EPL Ga (Zone 0).
INMETRO Intrinsic Safety [Fieldbus/FISCO]
Certificate: UL-BR 15.0030X
Standards: ABNT NBR IEC 60079-0:2008 + corrigendum 1:2011,
ABNT NBR IEC 60079-11:2009
Markings: Ex ia IIC T4 Ga (-60C < Ta < 60C)
See Table 4 at the end of the Product Certifications section for Entity Parameters.
Special Condition for Safe Use (X):
1. When mounted with the terminal options with transient protection, the equipment is
not capable of withstanding the dielectric strength test with 500 V as defined in ABNT
NBR IEC 60079-11. This feature should be taken into account during installation.
2. The enclosure may be made from aluminum alloy with a protective polyurethane paint
finish; however, care should be taken to protect it from impact and abrasion when
located in areas that require EPL Ga (Zone 0).
China
E3 China Flameproof
Certificate: GYJ11.1650X
Standards: GB3836.1-2000, GB3836.2-2010
Markings: Ex d IIC T5/T6 Gb

June 2016
16
Quick Start Guide
Special Conditions for Safe Use (X):
1. Symbol “X” is used to denote specific conditions of use: For information on the
dimensions of the flameproof joints the manufacturer shall be contacted. This shall be
mentioned in the manual.
2. Relation between T code and ambient temperature range is:
3. The earth connection facility in the enclosure should be connected reliably.
4. During installation, there should be no mixture harmful to flameproof housing.
5. During installation in hazardous location. Cable glands, conduits and blanking plugs,
certified by state-appointed inspection bodies with Ex d IIC Gb degree, should be used.
6. During installation, use and maintenance in explosive gas atmospheres, observe the
warning “Do not open when energized”.
7. End users is not permitted to change any components insides, but to settle the problem
in conjunction with manufacturer to avoid damage to the product.
8. When installation, use and maintenance of this product, observe following standards:
GB3836.13-1997 “Electrical apparatus for explosive gas atmospheres Part 13: Repair
and overhaul for apparatus used in explosive gas atmospheres”
GB3836.15-2000 “Electrical apparatus for explosive gas atmospheres Part 15: Electrical
installations in hazardous area (other than mines)”
GB3836.16-2006 “Electrical apparatus for explosive gas atmospheres Part 16:
Inspection and maintenance of electrical installation (other than mines)”
GB50257-1996 “Code for construction and acceptance of electric device for explosion
atmospheres and fire hazard electrical equipment installation engineering”
I3 China Intrinsic Safety
Certificate: GYJ11.1536X
Standards: GB3836.1-2000, GB3836.4-2010
Markings: Ex ia IIC T4/T5/T6
Special Conditions for Safe Use (X):
1. Symbol “X” is used to denote specific conditions of use:
a. The enclosure may contain light metal, attention should be taken to avoid ignition
hazard due to impact or friction when used in Zone 0.
b. When fitted with the “Transient Terminal Option”, this apparatus is not capable of
withstanding the 500 V r.m.s. insulation test required by Clause 6.3.12 of
GB3836.4-2010.
2. Relation between T code and ambient temperature range is:
T code Ambient temperature
T6 -40 °C ≤ Ta≤ +70 °C
T5 -40 °C ≤ Ta≤ +80 °C
Output T code Ambient temperature
HART
T6 –60 °C ≤ Ta≤ +70 °C
T5 –60 °C ≤ Ta≤ +70 °C
Fieldbus T4 –60 °C ≤ Ta≤ +60 °C

Quick Start Guide
17
June 2016
3. Parameters:
Power/loop terminals (+ and -)
Sensor terminal (1 to 5)
Load connected to sensor terminals (1 to 5)
Temperature transmitters comply to the requirements for FISCO field devices specified
in GB3836.19-2010. FISCO parameters are as follows:
4. The product should be used with Ex-certified associated apparatus to establish
explosion protection system that can be used in explosive gas atmospheres. Wiring and
terminals should comply with the instruction manual of the product and associated
apparatus.
5. The cables between this product and associated apparatus should be shielded cables
(the cables must have insulated shield). The shielded has to be grounded reliably in
non-hazardous area.
6. End users are not permitted to change any components insides, but to settle the
problem in conjunction with manufacturer to avoid damage to the product.
Output
Maximum
input
voltage:
Ui (V)
Maximum
input
current:
Ii (mA)
Maximum
inputpower:
Pi (W)
Maximum internal
parameters:
Ci (nF) Li (μH)
HART 30 300 1 5 0
Fieldbus 30 300 1.3 2.1 0
Output
Maximum
input
voltage:
Uo (V)
Maximum
input
current:
Io (mA)
Maximum
inputpower:
Po (W)
Maximum internal
parameters:
Co (nF) Lo (μH)
HART 30 300 1 5 0
Fieldbus 30 300 1.3 2.1 0
Output Group
Maximum external
parameters:
Co (μF) Lo (mH)
HART
IIC 0.74 11.7
IIB 5.12 44
IIA 18.52 94
Fieldbus
IIC 0.73 30.2
IIB 4.8 110.9
IIA 17.69 231.2
Maximum input
voltage:
Maximum input
current:
Maximum input
power:
Maximum internal
parameters
Ui(V) li(mA) Pi(W) Ci(nF) Li(μH)
17.5 380 5.32 2.1 0

June 2016
18
Quick Start Guide
7. When installation, use and maintenance of this product, observe following standards:
GB3836.13-1997 “Electrical apparatus for explosive gas atmospheres Part 13: Repair
and overhaul for apparatus used in explosive gas atmospheres”
GB3836.15-2000 “Electrical apparatus for explosive gas atmospheres Part 15: Electrical
installations in hazardous area (other than mines)”
GB3836.6-2006 “Electrical apparatus for explosive gas atmospheres Part 16: Inspection
and maintenance of electrical installation (other than mines)”
GB50257-1996 “Code for construction and acceptance of electric device for explosion
atmospheres and fire hazard electrical equipment installation engineering”
EAC - Belarus, Kazakhstan, Russia
EM Technical Regulation Customs Union (EAC) Flameproof
Certificate: RU C-US.GB05.B.00289
Markings: 1Ex d IIC T6…T1 Gb X
Special Condition for Safe Use (X):
1. See certificate for special conditions.
IM Technical Regulation Customs Union (EAC) Intrinsic Safety
Certificate: RU C-US.GB05.B.00289
Markings: [HART]: 0Ex ia IIC T5, T6 Ga X; [Fieldbus/Profibus]: 0Ex ia IIC T4 Ga X
Special Condition for Safe Use (X):
1. See certificate for special conditions.
Japan
E4 TIIS Flameproof
Certificate: TC21038, TC21039
Markings: Ex d IIC T5 (-20 °C ≤ Ta≤ +60 °C)
Certificate: TC16127, TC16128, TC16129, TC16130
Markings: Ex d IIB T4 (-20 °C ≤ Ta≤ +55 °C)
Combinations
K1 Combination of E1, I1, N1, and ND
K2 Combination of E2 and I2
K5 Combination of E5 and I5
K7 Combination of E7, I7, N7
KA Combination of K1 and K6
KB Combination of K5, I6, and K6
KM Combination of EM and IM

Quick Start Guide
19
June 2016
Tables
Additional certifications
SBS American Bureau of Shipping (ABS) Type Approval
Certificate: 02-HS289101-4-PDA
Intended Use: Measurement of temperature for marine and offshore applications.
SBV Bureau Veritas (BV) Type Approval
Certificate: 23154
Requirements: Bureau Veritas Rules for the Classification of Steel Ships
Application: Class notations: AUT-UMS, AUT-CCS, AUT-PORT and AUT-IMS;
Temperature transmitter type 3144P cannot be installed on diesel
engines
Table 3. Process Temperatures
T6 T5 T4 T3 T2 T1 T130
Max ambient + 40 °C + 60 °C + 60 °C + 60 °C + 60 °C + 60 °C + 70 °C
Sensor extension
Transmitter with LCD display
0-in. 55 °C 70 °C 95 °C 95 °C 95 °C 95 °C 95 °C
3-in. 55 °C 70 °C 100 °C 100 °C 100 °C 100 °C 100 °C
6-in. 60 °C 70 °C 100 °C 100 °C 100 °C 100 °C 100 °C
9-in. 65 °C 75 °C 110 °C 110 °C 110 °C 110 °C 110 °C
Transmitter without LCD display
0-in. 55 °C 70 °C 100 °C 170 °C 280 °C 440 °C 100 °C
3-in. 55 °C 70 °C 110 °C 190 °C 300 °C 450 °C 110 °C
6-in. 60 °C 70 °C 120 °C 200 °C 300 °C 450 °C 110 °C
9-in. 65 °C 75 °C 130 °C 200 °C 300 °C 450 °C 120 °C
Table 4. Entity Parameters
Parameter HART Fieldbus/PROFIBUS®FISCO
Voltage Ui(V) 30 30 17.5
Current Ii(mA) 300 300 380
Power Pi(W) 11.3 5.32
Capacitance Ci(nF) 52.1 2.1
Inductance Li(mH) 0 0 0

June 2016
20
Quick Start Guide
SDN Det Norske Veritas (DNV) Type Approval
Certificate: A-14184
Intended Use: Det Norske Veritas' Rules for Classification of Ships, High Speed & Light
Craft and Det Norske Veritas' Offshore Standards
Application:
SLL Lloyds Register (LR) Type Approval
Certificate: 11/60002
Application: Environmental categories ENV1, ENV2, ENV3, and ENV5
Location classes
Temperature D
Humidity B
Vibration A
EMC A
Enclosure D