Royalcraft LUGGAZ3X3.6-GREY User manual

- 2 -
1. Damages due to vandalism, abuse and incorrect use of the product are not covered by the warranty
2. Damages due to extreme weather conditions such as thunderstorm, hail and high winds are not
covered by warranty.
3. Canopy and/or Curtains will fade in the sunshine, the chemicals that make up the colours within the
polyester fabric are broken down by ultraviolet light that is present in the sunshine, this is a natural
process and is not covered by the guarantee or warranty. We do try to counteract this process by putting
a UV resistant additive to the fabric however this only protects the fabric for a certain amount of time.
Excluded
Note! This gazebo is meant to be used for decorative and sunshade purposes only and is
not meant to withstand all elements of the weather. Please remove all FABRIC during
adverse weather conditions.
Warning
4.. The screws/bolts to anchor to a wooden deck and concrete patio are not included.
5. DO NOT REMOVE THE PROTECTIVE FILM ON THE POLYCARBONATE ROOF PANELS
BEFORE INSTALLATION. MAKE SURE TO PUT THE UV PROTECTED SIDE FACING UP TO THE
SUN. IT IS A VERY IMPORTANT PROCEDURE; IF NOT FOLLOWED AS DESCRIBED, YOUR ROOF
WILL NOT BE COVERED BY THE GUARANTEE
Attention
1. It is the consumer's responsibility to comply with any relevant local planning requirements.
2. Two-Four persons are required for assembly. The tools required are a screwdriver or wrench, stepladder
and other relevant safety items such as gloves. We recommend the use of protective equipment.
3. This gazebo will take at least 1-2 hours to set up. You must allow enough time to complete the assembly.
Do not leave it unattended if not fully assembled, even if bolted to the ground.
A. Make sure that all components are in the box. Read instructions carefully before starting the assembly.
B. Follow all instructions carefully to assure the strength of the gazebo.
C. In order to avoid damage to the gazebo and its components, use appropriate tools. Do not use the
structure as a support; a stepladder is recommended.
D. Check all screws on a regular basis to maintain the solidity of the structure.
E. Keep the instructions and parts list for further use.
Maintenance
1. In the event that your gazebo needs replacement parts, repairs or you require assistance with regards
to assembly; please contact our customer sales team by email [email protected]
2. For cleaning: Use a mild domestic soap or soft detergent and wash with warm water using a sponge or
microfibre fabric. Rinse with clean water.
3. To preserve the fabric (curtains) we recommend the use of a UV protector spray like Fabsil. This will
help block the harmful UV rays from damaging the fabric and will also keep the fabric protected from
discoloration.
Your gazebo has been created for all four seasons and will resist snow accumulations of up to 5kg/m².
You will need to remove any excess of snow on the roof at all times.
The mosquito netting and the curtains must be removed for winter storage.
This Gazebo with curtains should only be used as a sunshade.
Make sure the product is fixed firmly to the ground or have a suitable weighted base to hold them in
place. If not secured or weighted down they will move position in high winds.
Please be aware that this product is not a permanent structure and we recommend removing the
curtains between October and March. These are the months when the weather will cause damage to
the fabric.

- 3 -

- 4 -
STEP ONE:
BOLTS NEEDED: H1
CONNECT PART A TO PART U
STEP TWO:
BOLTS NEEDED: H
2A. SLIDE 6 PART O INTO PARTS A1, A2, B1 AND B2
2B. CONNECT PART A1 WITH PA RT K
2C. CONNECT PART B1 WITH PART K

- 5 -
STEP THREE:
BOLTS NEEDED: H, H1, H2, H3
3A. CONNECT A1 TO B2 USING LEG A, PLACE YOUR J1 CORNER
BRACKET OVER ALL PARTS AND SECURE USING H3 (AS PER
DIAGRAM)
3B. CONNECT A2 TO B1 USING LEG A, PLACE YOUR J1 CORNER
BRACKET OVER ALL PARTS AND SECURE USING H3 (AS PER
DIAGRAM)
3C. CONNECT ALL PARTS TOGETHER IN THE MIDDLE USING
BRACKET K AND H BOLTS
3D. CONNECT PART J1 TO ALL CORNERS USING H3 BOLT
3E. CONNECT PART J2 TO THE MIDDLE SECTIONS USING H3 BOLT

- 6 -
STEP FOUR:
BOLTS NEEDED: H1
4A. CONNECT PART I TO PART C
4B. CONNECT PART G TO PART B
4C. CONNECT ALL PARTS B AND C TO PART F AND E (F IS TOP E IS BOTTOM
AS PER DIAGRAM)
STEP FIVE:
CONNECT YOUR BUILT ROOF SECTION TO YOUR BUILT FRAME SECTION
USING H1 BOLTS (AS PER DIAGRAM BELOW)

- 7 -
STEP SIX:
BOLTS NEEDED: H3, H4
SECTIONS 6A – 6C 3.6M SIDE
6A. SLIDE PANEL 1 THEN PART C1 THEN PANEL 3 INTO YOUR FRAME AND
CLOSE OFF WITH PART D2 (LEFT SIDE)
6B. SLIDE PANEL 5, THEN C2 AND THEN PANEL 6 INTO THE MIDDLE
SECTION AND CLOSE OFF WITH PART D
6C. SLIDE PANEL 2 THEN C1 THEN PANEL 4 INTO YOUR FRAME AND
CLOSE OFF WITH D1 (RIGHT SIDE)
6D. SLIDE PANEL 1 THEN PART C1 THEN PANEL 3 INTO YOUR FRAME AND
CLOSE OFF WITH D2
6E. SLIDE PANEL 2 THEN C1 THEN PANEL 4 INTO YOUR FRAME AND
CLOSE OFF WITH D1
6F. CONNECT PART N TO ALL CORNERS WITH H3 BOLT
6G. CONNECT PART M TO ALL MIDDLE SECTIONS WITH H3 BOLT
(AS SHOWN IN DIAGRAM BELOW)

- 8 -
STEP SEVEN:
7A. SLIDE PART X INTO THE INSIDE TRACK
7B. SLIDE PART W INTO THE OUTSIDE TRACK
7C. SECURE YOUR FRAME INTO THE GROUND USING PART Y (ONLY
AVAILABLE FOR GRASS) IF YOU WISH TO SECURE TO CONCRETE YOU
WILL NEED TO PURCHASE BOLTS FOR THIS.