Royalcraft Turnbury FSC110206 User manual

Turnbury 2/3 Seater Bench
ITEM CODE: FSC110206, FSC110207
Produced in China for A. Mir & Co., Ltd.
© A. Mir & Co., Ltd. 1 / 4
www.ro
y
alcraft.co.uk
Assembly Instructions
Product size:
W120*D59*H92 cm (2 Seater Bench)
W150*D59*H92 cm (3 Seater Bench)
Furniture should be covered/stored whilst not in use
to prolong its longevity.
(It should also be covered in adverse weather.)
This product is for domestic use only.
IMPORTANT, PLEASE RETAIN FOR FUTURE REFERENCE
READ CAREFULLY

Turnbury 2/3 Seater Bench
ITEM CODE: FSC110206, FSC110207
Produced in China for A. Mir & Co., Ltd.
© A. Mir & Co., Ltd. 2 / 4
www.ro
y
alcraft.co.uk
Before you start
Warnings
IMPORTANT, RETAIN FOR FUTURE REFERENCE
READ CAREFULLY
See enclosed instructions for assembly, safety and care information.
Failure to follow the warnings could result in serious injury.
Handle heavy parts with care.
Ensure that this product is fully assembled as illustrated before use.
This product should only be used on firm, level ground.
The product contains small parts which could pose a risk to young
children. Keep small parts out of reach of children.
Do not stand or climb onto this product.
This product is intended for domestic use only.
Ensure the product is always placed on level ground.
Furniture can be dangerous if incorrectly used. No liability will be accepted
for damage or injury caused by incorrect use of this product.
Take care when opening and folding furniture. Keep your hands away from
moving parts in order to prevent trapping your fingers. Children should not
open or close the furniture.
This table is not intended to support a parasol separately. A parasol
base with suitable weight must be used to support your parasol.
Dos
When you are ready to start, make sure that you have the right tools, plenty
of space and a clean, dry area for assembly.
Unwrap all packaging materials and place the components on suitable
surface to prevent scratching your product.
Check the pack and make sure you have all of the parts listed. In the event
of problems or missing parts, please contact the seller.
Check all screws and bolts are tightened and inspect regularly.
During severe weather conditions, including high winds, rain, hail,
thunderstorms, extreme heat and cold temperatures, the product should be
stored inside in a cool, dry place.
To best preserve this product, please use a protective cover when your
furniture is not in use. We would also recommend using a gazebo or parasol
over your furniture during the summer period and prolonged sunny spells.
This will help prevent harmful UV rays from damaging and discolouring the
material.
Timber is a natural product and contains coloured resins which may initially
bleed out of the timber when its gets wet. Therefore we recommend that
care is taken to protect patios and decking from possible staining where the
product comes into contact with the ground. The furniture will stabilise in its
environment after the first few times it gets wet.
Wood is a natural material whose appearance will deteriorate when left
outside. A surface coating is vital in protecting it from premature darkening,
or splitting, when exposed to the weather. The finish should be regularly
maintained to ensure that the wood is protected from moisture and the
furniture continues to look at its best.
This product has been treated with furniture oil during manufacture and the
wood requires further treatment before being left out side. When applying
furniture oil particular care should be given to the end grain and any joints or
crevices, please note that is the products needs to be put together the first
coat should be applied to all wood surfaces before assembly.
Should you choose not to treat your furniture, then it will turn a greyish
colour and develop cracks. Light sanding can restore the original colour
after which furniture oil can be regularly applied in accordance with the
instructions above.
A liberal coating of furniture oil should be given to the furniture before it is
laid up, and again when it is removed from storage.
Clean your product with a sponge and warm soapy water then wipe with a
clean, dry cloth.
Ensure that the product is clean and dry before storage.
Where instructions as to the; storage, commissioning, installation, use and
maintenance of the goods or (if there is none) good trade practice are not
followed and a defect arises this will void the 12 month manufacturer's
guarantee on the product.
Don’ts
Do not use scourers, abrasives, washing powders, chemical cleaners or any
other substances containing abrasives since these substances can damage
the product.
To preserve the product do not place greasy / oily items directly onto the
wooden surface.
Do not place very hot or very cold items on the wooden surface unless
adequately thick place-mats are used to prevent such items from coming into
contact with the wood.
Do not strike the product with hard or pointed items.
Do not sit or lean on the arms of this product.
Do not use power tools to construct this product.
Do not tighten screws until fully assembled.
Do not overtighten screws or bolts.
Do not use this product if parts are missing, damaged or worn.
Do not stand or climb onto the product and do not use it as a ladder, as this
could lead to it unbalancing and overturning.
Never tilt the product during use.
Never drag furniture when moving it, always lift it.
This item is intended for max use 120 kgs, do not exceed this weight.
Number of people required for assembly
Two people
Time to assemble Tools required
30 minutes

Turnbury 2/3 Seater Bench
ITEM CODE: FSC110206, FSC110207
Produced in China for A. Mir & Co., Ltd.
© A. Mir & Co., Ltd. 3 / 4
www.ro
y
alcraft.co.uk
Components, fixtures & fittings (not actual size)
Parts List
Part
No. Diagram Qty. Part No. Diagram Qty.
A
Right Leg
1 PC B
Left Leg
1 PC
C
Backrest
1 PC D
Seat
1 PC
1
Male Bolt
M6*40mm
4 PCS 2
Self-Taping Screw
M7*100mm
6 PCS
3
Allen Key
1 PC
mm
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
190
200
210
220
0

Turnbury 2/3 Seater Bench
ITEM CODE: FSC110206, FSC110207
Produced in China for A. Mir & Co., Ltd.
© A. Mir & Co., Ltd. 4 / 4
www.ro
y
alcraft.co.uk
Step by step assembly instructions
Step One
Step Two
With the help of another person, turn over the above partly-assembled bench,
connect the Leg (A, B) and Seat (D) using Bolts (1). Tighten with Allen Key (3).
Stand the Bench, your bench is now ready for use.
PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE
2
3
X6
A
B
C
D
With the help of another person, attach the Right Leg (A), Left Leg (B), Backrest (C) and
Seat (D) as per the diagram using Self-Taping Screws (2).
Tighten with Allen Key (3).
X4
1
3