Royalcraft FARO-15 User manual

Faro Double Sunlounger with Cushion
Assembly Instructions
Produced in China for A Mir & Co., Ltd.
© A Mir & Co., Ltd. 2 / 5
www.royalcraft.co.uk
Before you start
Warnings
IMPORTANT, RETAIN FOR FUTURE
REFERENCE
READ CAREFULLY
See enclosed instructions for safety and care
information.
Failure to follow the warnings could result in serious
injury.
Handle heavy parts with care.
Thisproduct is intended for Domestic Use only.
This product should only be used on firm, level
ground.
Ensure the product is always placed on level
ground.
Furniture can be dangerous if used incorrectly or
maintained poorly. Keep your furniture in a good
condition at all times. No liability will be accepted for
damage or injury caused by failure to follow the care
and maintenance guidelines.
Dos
Unwrap all packaging materials and place the
components on suitable surface to prevent
scratching your product.
We recommend the use of furniture covers to
protect your product when not in use.
Cushions should be cleaned following the care
instruction onthe label.
If the set is stored outside then we recommend that
cushions are brought inside for storage and
protection.
To clean theproduct, a pressure washer or jet wash
on a wide spray can be used at a minimum distance
of 1m from the product. Do not aim this directly at
the joints of the furniture. Alternatively it can simply
be wiped down by hand with a damp sponge and a
weak solution of soap and water.
We would recommend lifting the products to move
the items instead of dragging them which may
cause some damage to either the product or the
area in which you choose to use them.
Don’ts
Never drag furniture when moving it, always lift it.
Never tilt the product use.
Do not stand or climb onto the product.
Do not sit or lean onto the arms/rims of this product.
Never use scourers, abrasives or chemical cleaner.
Number of people required for assembly
Two people
Time to assemble
15Minutes
Tools required
(Rubber Hammer may be required, not provided)

Produced in China for A Mir & Co., Ltd.
© A Mir & Co., Ltd. 3 / 6
www.royalcraft.co.uk
Components, fixtures & fittings (not actual size)
Parts List
Part
No. Diagram Qty. Part No. Diagram Qty.
F+B
Seat
2 PCS CB
Backrest
2 PCS
MB
Middle Part
1 PC MF
Middle Part
1 PC
M1
Leg
4 PCS M2
Leg
2 PCS
M3
Leg
4 PCS M4
Leg
2 PCS
E
Cushion
2 PCS
mm
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
190
200
210
220
0
Faro Double Sunlounger with Cushion
Assembly Instructions

Produced in China for A Mir & Co., Ltd.
© A Mir & Co., Ltd. 4 / 6
www.royalcraft.co.uk
Step by step assembly instructions
Step One
Please note the two Seats (F+B) are folded when taking out from the carton.
Place the Seats (F+B) on the ground, unfold them.
Step Two
Please locate the assembly joints carefully.
Combine the Middle Part (MB) and (MF); and attach them to each side of the Seats (F+B).
F+B
MB
MF
F+B
F+B
Faro Double Sunlounger with Cushion
Assembly Instructions

Produced in China for A Mir & Co., Ltd.
© A Mir & Co., Ltd. 5 / 6
www.royalcraft.co.uk
Step Three
Attach all Legs (M1, M2, M3, M4) as per below diagram onto the reverse side of the
Seats (F+B).
Step Four
Attach Backrests (CB) to the Seats (F+B).
M1
M1
M1
M1 M3
M3
M2
M2
M4
F+B
F+B
CB
Faro Double Sunlounger with Cushion
Assembly Instructions

Produced in China for A Mir & Co., Ltd.
© A Mir & Co., Ltd. 6 / 6
www.royalcraft.co.uk
Step Five
Place the Cushions (E) to the Seats (F+B), fasten the Belts.
Your Double Sunlounger is now ready for use.
Never tilt the products during use.
Ensure the product is always placed firmly on the ground.
PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE
E
Faro Double Sunlounger with Cushion
Assembly Instructions