Ruijie RG-IS2700-P Series Installation manual

RG-IS2700-P Series PoE Switch
RGOS Command Reference

·
Copyright Statement
Ruijie Networks©2018
Ruijie Networks reserves all copyrights of this document. Any reproduction, excerption, backup, modification,
transmission, translation or commercial use of this document or any portion of this document, in any form or by any means,
without the prior written consent of Ruijie Networks is prohibited.
Exemption Statement
This document is provided “as is”. The contents of this document are subject to change without any notice. Please obtain
the latest information through the Ruijie Networks website. Ruijie Networks endeavors to ensure content accuracy and will
not shoulder any responsibility for losses and damages caused due to content omissions, inaccuracies or errors.

·
Preface
Thank you for using our products. This manual matches the RGOS Firmware Version 1.00.xx.
Audience
This manual is intended for:
Network engineers
Technical support and servicing engineers
Network administrators
Obtaining Technical Assistance
Ruijie Networks Website: https://www.ruijienetworks.com/
Technical Support Website: https://ruijienetworks.com/support
Case Portal: http://caseportal.ruijienetworks.com
Community: http://community.ruijienetworks.com
Technical Support Email: [email protected]
Skype: [email protected]
Related Documents
Documents
Description
Hardware Installation and Reference
Guide
Describes the functional and physical features and provides the device
installation steps, hardware troubleshooting, module technical specifications,
and specifications and usage guidelines for cables and connectors.

·
L2 Features Configuration Commands
1. Port Configuration Commands
2. MAC Address Table
3. Jumbo Frame Commands
4. Flow Control Commands
5. Spanning Tree Commands
6. VLAN Commands
7. Q-in-Q Commands
8. Link Aggregation Commands
9. GARP Commands
10.GVRP Commands
11.Port Mirror Commands
12.LLDP Commands

Command Reference Port Configuration Commands
1 Port Configuration Commands
1.1 [no] shutdown
Use "shutdown" command to disable port and use "no shutdown" to enable port. If port is error
disabled for any reason, use "no shutdown" command to recover the port manually.
[no] shutdown
Command
Mode
Privileged EXEC mode
Configuration
Examples
This example shows how to disable one of the ports.
switch(config)# interface gi1
switch(config-if)# shutdown"
1.2 speed
Use "speed" command to change port speed configuration. The speed is only able to configure to the
physical maximum speed. For example, in fast Ethernet port, speed 1000 is not available.
speed (10|100)
speed (1000|)
speed auto[(10|100|10/100)]
speed auto[(1000|)]
Command
Mode
Privileged EXEC mode
Configuration
Examples
This example shows how to modify port speed configuration.
switch(config)# interface gi2
switch(config-if)# speed auto 10/100
1.3 duplex(auto|full|half)
Use "duplex" command to change port duplex configuration.
duplex(auto|full|half)
Command
Mode
Privileged EXEC mode
Configuration
Examples
This example shows how to modify port duplex configuration.
switch(config)# interface gi1
switch(config-if)# duplex full
switch(config-if)# exit

Command Reference Port Configuration Commands
switch(config)# interface gi2
switch(config-if)# duplex half
1.4 description
Use "description" command to give the port a name to identify it easily. If description includes space
character, please use double quotes to wrap it.
description string
Command
Mode
Privileged EXEC mode
Configuration
Examples
This example shows how to modify port descriptions.
switch(config)# interface gi2
switch(config-if)# description "uplink port"
1.5 no description
Use no form to restore description to empty string.
no description
Command
Mode
Privileged EXEC mode
1.6 [no] protected
Use "protected" command to protect port. Protected port is only allowed to communicate with
unprotected port. In other words, protected port is not allowed to communicate with another protected
port. Use no form to make port unprotected.
[no] protected
Command
Mode
Privileged EXEC mode
Configuration
Examples
This example shows how to configure ports gi1 and gi2 as protected ports.
switch(config)# interface range gi1-2
switch(config-if-range)# protected

Command Reference MACAddress Table Commands
2 MAC Address Table Commands
2.1 show mac address- table aging-time
View the aging time of the address table.
show mac address-table aging-time
Command
Mode
User EXEC mode
Configuration
Examples
switch# show mac address-table aging-time
2.2 show mac address-table A:B:C:D:E:F
Displays entries for a specific MAC address (for all or VLAN).
show mac address-table A:B:C:D:E:F [vlan <1-4094>]
Command
Mode
User EXEC mode
Configuration
Examples
switch# show mac address-table 0:1:2:3:4:5 vlan 1
2.3 show mac address- table
View MAC entry on specified interface or VLAN or all dynamic MAC entries in MAC address table.
show mac address-table [vlan <14094>] [interfaces IF_PORTS]
Command
Mode
User EXEC mode
Configuration
Examples
switch# show mac address-table vlan 1 interface gi5
2.4 show mac address- table static
View static MAC entry on specified interface or VLAN or all dynamic MAC entries in MAC address
table.
show mac address-table static [vlan <1-4094>] [interfaces IF_PORTS]
Command
Mode
User EXEC mode
Configuration
Examples
switch# show mac address-table static vlan 1 interface gi5

Command Reference MACAddress Table Commands
2.5 show mac address- table dynamic
View dynamic MAC entry on specified interface or VLAN or all dynamic MAC entries in MAC address
table.
show mac address-table dynamic [vlan <1-4094>] [interfaces IF_PORTS]
Command
Mode
User EXEC mode
Configuration
Examples
switch# show mac address-table dynamic vlan 1 interface gi5
2.6 show mac address- table counters
Display the number of addresses present in MAC address table.
show mac address-table counters
Command
Mode
User EXEC mode
Configuration
Examples
switch# show mac address-table counters
2.7 clear mac address- table dynamic
Delete dynamic MAC entry on specified interface or all dynamic MAC entries in MAC address table.
clear mac address-table dynamic [interfaces IF_PORTS]
Command
Mode
Privileged EXEC mode
Configuration
Examples
switch(config)# clear mac address-table dynamic interfaces gi5
2.8 clear mac address- table dynamic vlan
Delete dynamic MAC entry on specified VLAN dynamic MAC entry in MAC address table.
clear mac address-table dynamic vlan <1-4094>
Command
Mode
Privileged EXEC mode
Configuration
Examples
switch(config)# clear mac address-table dynamic vlan 1
2.9 mac address-table aging-time
Set the aging time of the address table.
mac address-table aging-time <10630>

Command Reference MACAddress Table Commands
Command
Mode
Privileged EXEC mode
Configuration
Examples
switch(config)# mac address-table aging-time 300
2.10 mac address-table static A:B:C:D:E:F vlan
Add static addresses to the MAC address table.
mac address-table static A:B:C:D:E:F vlan <1-4094> interfaces IF_PORTS
Command
Mode
Privileged EXEC mode
Configuration
Examples
switch(config)# mac address-table static 0:1:2:3:4:5 vlan 1 interfaces gi5
2.11 no mac address-table static A:B:C:D:E:F vlan
Delete static addresses from the MAC address table.
no mac address-table static A:B:C:D:E:F vlan <1-4094>
Command
Mode
Privileged EXEC mode
Configuration
Examples
switch(config)# no mac address-table static 0:1:2:3:4:5 vlan 1 interfaces gi5

Command Reference Jumbo Frame Commands
3 Jumbo Frame Commands
3.1 jumbo-frame
Use "jumbo-frame" com-mand to modify maximum frame size. The only way to show this
configuration is by using "show running-config" command.
jumbo-frame <1518- 9216>
Command
Mode
Privileged EXEC mode
Configuration
Examples
This example shows how to modify maximum frame size to 9216 bytes.
switch(config)# jumbo-frame 9216
3.2 no jumbo-frame
Use no form to disable jumbo-frame.table.
no jumbo-frame
Command
Mode
Privileged EXEC mode
Configuration
Examples
switch(config)# no jumbo-frame
4 Flow Control Commands
4.1 [no] back-pressure
Use " back-pressure " command to change port back pressure configuration. Use no form to restore
back-pressure to default (off) configuration.
[no] back-pressure
Command
Mode
Privileged EXEC mode
Configuration
Examples
This example shows how to modify port duplex configuration.
switch(config)# interface gi1
switch(config-if)# back-pressure
switch(config-if)# no back-pressure
4.2 flowcontrol
Use " flow-control " command to change port flow control configuration. Use off form to restore flow
control to default (off) configuration.