Ruijie RG-S2910-24GT4SFP-UP-H Installation and operating manual

RG-S2910-H Series Switch
Hardware Installation and Reference Guide V1.22

Copyright Statement
Ruijie Networks©2017
Ruijie Networks reserves all copyrights of this document. Any reproduction, excerption, backup,
modification, transmission, translation or commercial use of this document or any portion of this document,
in any form or by any means, without the prior written consent of Ruijie Networks is prohibited.
Exemption Statement
This document is provided “as is”. The contents of this document are subject to change without any notice.
Please obtain the latest information through the Ruijie Networks website. Ruijie Networks endeavors to
ensure content accuracy and will not shoulder any responsibility for losses and damages caused due to
content omissions, inaccuracies or errors.

Preface
Thank you for using our products. This manual will guide you through the installation of the device.
This manual describes the functional and physical features and provides the device installation steps,
hardware troubleshooting, module technical specifications, and specifications and usage guidelines for
cables and connectors.
Audience
It is intended for the users who have some experience in installing and maintaining network hardware. At
the same time, it is assumed that the users are already familiar with the related terms and concepts.
Obtaining Technical Assistance
Ruijie Networks Website: http://www.ruijienetworks.com/
Service Email: [email protected]
Technical Support: http://www.ruijienetworks.com/service.aspx
Technical Support Hotline: [phone]
Related Documents
Documents
Description
Configuration Guide
Describes network protocols and related mechanisms that
supported by the product, with configuration examples.
Command Reference
Describes the related configuration commands, including
command modes, parameter descriptions, usage guides, and
related examples.
Symbol Conventions
The symbols used in this document are described as below:
This symbol brings your attention to some helpful suggestions and references.
This symbol means that you must be extremely careful not to do some things that may damage the
device or cause data loss

1 Product Overview
The RG-S2910-H series switch is a next-generation intelligent switch that features high performance, high security,
multiple services and ease of use to meet the needs of the current networks. The RG-S2910-H series switch can provide
the complete end-to-end Quality of Service (QoS), flexible and abundant security policies and policy-based network
management for various networks. It is greatly ideal for such applications as campus network, enterprise network,
government network, service network, residential broadband access and business building network, providing high-speed,
high-efficiency, secure and intelligent access solutions.
Table 1-1 RG-S2910-H
Model
10/100/1000 Base-T
Auto-sensing Ethernet Port
SFP+
Port
1000Base-X
SFP Port
Console
Port
USB
Port
Pluggable
Power
Slot
RG-S2910-24GT4SFP-UP-H
24 (All are PoE+ capable.
Ports 1-4 are HPoE capable)
\
4
1
\
\
RG-S2910-10GT2SFP-UP-H
10 (Ports 1-8 are HPoE
capable)
\
2
1
\
\
RG-S2910-24GT4XS-UP-H
24 (All are PoE+ capable.
Ports 1-4 are HPoE capable)
4
\
1
\
\
The SPF+ ports are downward compatible with 1000Base-X. The SFP ports only support 1000Base-X modules.
1000Base-T is compatible with 100Base-TX and 10Base-T in the downlink direction.
For RG-S2910-24GT4SFP-UP-H /RG-S2910-24GT4XS-UP-H, the HPoE ports support 60W power supply and
support IEEE 802.af/at PoE.
For RG-S2910-10GT2SFP-UP-H, the HPoE ports support 95W power supply and support IEEE 802.af/at PoE.
1.1 RG-S2910-24GT4SFP-UP-H
Technical Specifications
Model
RG-S2910-24GT4SFP-UP-H
CPU
Built-in CPU, single-core processor, 1GHz
Flash Memory
512M
SDRAM
DDRIII 512MB
Optical Module
For details, see Appendix B.
The supported module type may change at any time. Consult us for the latest information.
SFP Port
Supports 1000Base-X modules. Does not support 100Base-FX.
When the SFP ports are used as stack ports:
When used as stack ports, SFP ports of hardware versions V1.XX only support 10G DAC

copper cables (XG-SFP-CU1M, XG-SFP-CU3M and XG-SFP-CU5M); SFP ports of
hardware versions V2.XX support 10G DAC copper cables (XG-SFP-CU1M,
XG-SFP-CU3M and XG-SFP-CU5M), 2.5G DAC copper cables (GE-SFP-STACK1.6M),
and SFP transceiver modules.
Power Supply
AC input
Rated voltage range: 100V to 240V
Maximum voltage range: 90V to 264V
Frequency: 50/60 Hz
Rated current: 6.8A
HVDC input
Voltage range: 192V to 290V
Current range: 2.5A to 3.5A
EEE
Supported
PoE
All the RJ45 ports are PoE-capable. Ports 1-4 are HPoE-capable with the maximum power
output of 60W. Ports 5-24 support the maximum power output of 30W.
The maximum output power of PoE/PoE+/HPoE is 370W.
The HPoE ports support the maximum power supply of 60W only when connected with
HPoE PDs. For example, RG-PBOX-DC12 and RG-PBOX-AC24.
HPoE ports support IEEE 802.af/at PoE.
The available number of PDs is determined by PSE output power and PD input power in
practice.
Power
Consumption
Less than 40W with no PoE load
Less than 460W with PoE full load
Operating
Temperature
0℃to 50℃
Storage
Temperature
-40℃to 70℃
Operating Humidity
10% to 90%
Storage Humidity
5% to 95%
Fan
Speed adjustment and fault alarm
Temperature
Warning
Supported
EMCStandards
GB9254-2008
EN 300 386
EN 61000-3-2
EN 61000-3-3
EN 61000-4-2
EN 61000-4-3
EN 61000-4-4
EN 61000-4-5

EN 61000-4-6
EN 61000-4-11
EN 55022
EN 55024
EN 61000-4-8
Security Standards
GB4943-2011
EN60950-1
IEC60950-1
Dimensions
(W x D x H)
440 mm x 260 mm x 44 mm
Weight
≤5.5 kg (with package)
The RG-S2910-24GT4SFP-UP-H switch is a class A product. In a domestic environment, this product may cause
radio interference in which case the user may be required to take adequate measures.
Product Appearance
On the front panel, the RG-S2910-24GT4SFP-UP-H Ethernet switch provides 24 10/100/1000Base-T Ethernet ports, 4
SFP ports, and 1 Console port. On the back panel, it provides AC power ports.
Figure 1-1 Appearance of RG-S2910-24GT4SFP-UP-H
Front Panel
Figure 1-2 Front Panel of RG-S2910-24GT4SFP-UP-H

Note:
1. System status LED
2. PoE status LED
3. Copper port status LED
4. Fiber port status LED
5. PoE Mode Switch-Over Button
6. Console port
7. 10/100/1000Base-T auto-sensing Ethernet port
8. 1000Base-X SFP port
9. 1000Base-X SFP port
Long press PoE Mode Switch-Over Button for above 2 seconds to switch the display mode between PoE mode and
port rate mode.
Back Panel
Figure 1-3 Back Panel of RG-S2910-24GT4SFP-UP-H
Note:
1. Grounding pole
Power Supply
The RG-S2910-24GT4SFP-UP-H switch adopts AC or HVDC power input.
AC input
Rated voltage range: 100V to 240V
Maximum voltage range: 90V to 264V
Frequency range: 50/60 Hz
Rated current: 6.8A
Power cord specification: 10A
HVDC input
Voltage range: 192V to 290V
Current range: 2.5A to 3.5A
Heat Dissipation
The RG-S2910-24GT4SFP-UP-H adopts turbine fans for heat dissipation, thereby ensuring normal function of the device
in the specified environment. 10 cm distance space should be reserved at both sides and the back plane of the cabinet to

allow air circulation. It is recommended to clean the device once every 3 months to avoid dust from blocking vents. Figure
1-4 shows the flow scheme of heat dissipation.
Figure 1-4 Flow Scheme of Heat Dissipation
LEDs
LED
Panel Identification
State
Meaning
System status LED
Status
Off
The switch is not receiving power.
Blinking green
The system is being initialized.
Continuous blinking indicates errors.
Solid green
The switch is operational.
Solid yellow
Temperature warning
Check the working environment of the switch
immediately.
Solid red
The switch is faulty.
PoE status LED
PoE
Solid green
Indicates the switching state.
Solid yellow
Indicates the PoE state.
1-24
Off
The port is not connected.

1000Mbps RJ-45 port
status LED
Solid green
The port is connected at 1000 Mbps.
Blinking green
The port is receiving or transmitting traffic at 1000
Mbps.
Solid yellow
The port is connected at 10/100 Mbps.
Blinking yellow
The port is receiving or transmitting traffic at
10/100 Mbps.
RJ45 port PoE status
LED
1-24
Off
PoE is not enabled.
Solid green
PoE is enabled. The port is operational.
Solid yellow
The PoE port is abnormally operational.
1000Mbps SFP port
status LED
25F-28F
Off
The port is not connected.
Solid green
The port is connected at 1000 Mbps.
Blinking green
The port is receiving or transmitting traffic at 1000
Mbps.
1.2 RG-S2910-24GT4XS-UP-H
Technical Specifications
Model
RG-S2910-24GT4XS-UP-H
CPU
Built-in CPU, single-core processor, 1GHz
Flash Memory
512M
SDRAM
DDRIII 512MB
Optical Module
For details, see Appendix B.
The supported module type may change at any time. Consult us for the latest information.
SFP Port
Supports 10GBase-R and 1000Base-X modules.
When used as stack ports, SFP+ ports support 10G DAC copper cables (XG-SFP-CU1M,
XG-SFP-CU3M, and XG-SFP-CU5M) and SFP+ transceiver modules.
Power Supply
AC input
Rated voltage range: 100V to 240V
Maximum voltage range: 90V to 264V
Frequency: 50/60 Hz
Rated current: 6.8A

HVDC input
Voltage range: 192V to 290V
Current range: 2.5A to 3.5A
EEE
Supported
PoE
All the RJ45 ports are PoE-capable. Ports 1-4 are HPoE-capable with the maximum power
output of 60W. Ports 5-24 support the maximum power output of 30W.
The maximum output power of PoE/PoE+/HPoE is 370W.
The HPoE ports support the maximum power supply of 60W only when connected with
HPoE PDs. For example, RG-PBOX-DC12 and RG-PBOX-AC24.
HPoE ports support IEEE 802.af/at PoE.
The available number of PDs is determined by PSE output power and PD input power in
practice.
Power
Consumption
Less than 40W with no PoE load
Less than 460W with PoE full load
Operating
Temperature
0℃to 50℃
Storage
Temperature
-40℃to 70℃
Operating Humidity
10% to 90%
Storage Humidity
5% to 95%
Fan
Speed adjustment and fault alarm
Temperature
Warning
Supported
EMCStandards
GB9254-2008
Security Standards
GB4943-2011
Dimensions
(W x D x H)
440 mm x 260 mm x 44 mm
Weight
≤5.5 kg (with package)
The RG-S2910-24GT4XS-UP-H switch is a class A product. In a domestic environment, this product may cause
radio interference in which case the user may be required to take adequate measures.
Product Appearance
On the front panel, the RG-S2910-24GT4XS-UP-H Ethernet switch provides 24 10/100/1000Base-T Ethernet ports, 4
SFP+ ports, and 1 Console port. On the back panel, it provides AC power ports.
Figure 1-5 Appearance of RG-S2910-24GT4XS-UP-H

Front Panel
Figure 1-6 Front Panel of RG-S2910-24GT4XS-UP-H
Note:
1. System status LED
2. PoE status LED
3. Copper port status LED
4. Fiber port status LED
5. PoE Mode Switch-Over Button
6. Console port
7. 10/100/1000Base-T auto-sensing Ethernet port
8. SFP+ port
Long press PoE Mode Switch-Over Button for above 2 seconds to switch the display mode between PoE mode and
port rate mode.
Back Panel
Figure 1-7 Back Panel of RG-S2910-24GT4XS-UP-H
Note:
1. Grounding pole
Power Supply
The RG-S2910-24GT4XS-UP-H switch adopts AC or HVDC power input.
AC input

Rated voltage range: 100V to 240V
Maximum voltage range: 90V to 264V
Frequency range: 50/60 Hz
Rated current: 6.8A
Power cord specification: 10A
HVDC input
Voltage range: 192V to 290V
Current range: 2.5A to 3.5A
Heat Dissipation
The RG-S2910-24GT4XS-UP-H adopts turbine fans for heat dissipation, thereby ensuring normal function of the device in
the specified environment. 10 cm distance space should be reserved at both sides and the back plane of the cabinet to
allow air circulation. It is recommended to clean the device once every 3 months to avoid dust from blocking vents. Figure
1-8 shows the flow scheme of heat dissipation.
Figure 1-8 Flow Scheme of Heat Dissipation
LEDs
LED
Panel Identification
State
Meaning
System status LED
Status
Off
The switch is not receiving power.

Blinking green
The system is being initialized.
Continuous blinking indicates errors.
Solid green
The switch is operational.
Solid yellow
Temperature warning
Check the working environment of the switch
immediately.
Solid red
The switch is faulty.
PoE status LED
PoE
Solid green
Indicates the switching state.
Solid yellow
Indicates the PoE state.
1000Mbps RJ-45 port
status LED
1-24
Off
The port is not connected.
Solid green
The port is connected at 1000 Mbps.
Blinking green
The port is receiving or transmitting traffic at 1000
Mbps.
Solid yellow
The port is connected at 10/100 Mbps.
Blinking yellow
The port is receiving or transmitting traffic at
10/100 Mbps.
RJ45 port PoE status
LED
1-24
Off
PoE is not enabled.
Solid green
PoE is enabled. The port is operational.
Solid yellow
The PoE port is abnormally operational.
SFP+ port status LED
25F-28F
Off
The port is not connected.
Solid green
The port is connected.
Blinking green
The port is receiving or transmitting traffic.

1.3 RG-S2910-10GT2SFP-UP-H
Technical Specifications
Model
RG-S2910-10GT2SFP-UP-H
CPU
Built-in CPU, single-core processor, 400MHz
Flash Memory
256M
SDRAM
DDRIII 512MB
Optical Module
Supports 1000base-X only. For details, see Appendix B.
The supported module type may change at any time. Consult us for the latest information.
SFP Port
Supports 1000Base-X modules.
Power Supply
AC input
Rated voltage range: 100V to 240V
Maximum voltage range: 90V to 264V
Frequency: 50/60 Hz
Rated current: 8A
HVDC input
Voltage range: 192V to 290V
Current range: 0A to 6A
EEE
Supported
PoE
Ports 1-8 are HPoE-capable with the maximum power output of 95W.
The maximum output power is as follows.
AC input
90 to175VAC: 380W
175 to 264VAC: 760W
HVDC input
192 to 220VDC: 380W
220 to 290VDC: 760W
The HPoE ports support the maximum power supply of 95W only when connected with
HPoE PDs. For example, RG-PBOX-DC12 and RG-PBOX-AC24.
HPoE ports support IEEE 802.af/at PoE.
The available number of PDs is determined by PSE output power and PD input power in
practice.
Power
Consumption
Less than 30W with no PoE load
Less than 870W with full PoE load
Operating
Temperature
0℃to 50℃
Storage
Temperature
-40℃to 70℃

Operating Humidity
10% to 90%
Storage Humidity
5% to 95%
Fan
Speed adjustment and fault alarm
Temperature
Warning
Supported
EMCStandards
GB9254-2008
Security Standards
GB4943-2011
Dimensions
(W x D x H)
340 mm x 260 mm x 44 mm
Weight
≤4.0 kg (with package)
The RG-S2910-10GT2SFP-UP-H switch is a class A product. In a domestic environment, this product may cause
radio interference in which case the user may be required to take adequate measures.
Product Appearance
On the front panel, the RG-S2910-10GT2SFP-UP-H Ethernet switch provides 10 10/100/1000Base-T Ethernet ports, 2
SFP ports, and 1 Console port. On the back panel, it provides AC power ports.
Figure 1-9 Appearance of RG-S2910-10GT2SFP-UP-H
Front Panel
Figure 1-10 Front Panel of RG-S2910-10GT2SFP-UP-H

Note:
1. System status LED
2. PoE status LED
3. 10/100/1000Base-T auto-sensing Ethernet
port
4. Copper port status LED
5. Copper port status LED
6. Fiber port status LED
7. PoE Mode Switch-Over Button
8. Console port
9. 10/100/1000Base-T auto-sensing Ethernet port
10. 1000Base-X SFP port
11. Reset Button
Long press PoE Mode Switch-Over Button for above 2 seconds to switch the display mode between PoE mode and
port rate mode.
Back Panel
Figure 1-11 Back Panel of RG-S2910-10GT2SFP-UP-H
Note:
Grounding pole
Air exhaust
Air exhaust
Power Supply
The RG-S2910-10GT2SFP-UP-H switch adopts AC or HVDC power input.
AC input
Rated voltage range: 100V to 240V
Maximum voltage range: 90V to 264V
Frequency range: 50/60 Hz
Rated current: 8A
Power cord specification: 10A

HVDC input
Voltage range: 192V to 290V
Current range: 0A to 6A
Heat Dissipation
The RG-S2910-10GT2SFP-UP-H adopts turbine fans for heat dissipation, thereby ensuring normal function of the device
in the specified environment. 10 cm distance space should be reserved at both sides and both planes of the cabinet to
allow air circulation. It is recommended to clean the device once every 3 months to avoid dust from blocking vents. Figure
1-12 shows the flow scheme of heat dissipation.
Figure 1-12 Flow Scheme of Heat Dissipation
LEDs
LED
Panel Identification
State
Meaning
System status LED
Status
Off
The switch is not receiving power.
Blinking green
The system is being initialized.
Continuous blinking indicates errors.
Solid green
The switch is operational.

Solid yellow
Temperature warning
Check the working environment of the switch
immediately.
Solid red
The switch is faulty.
PoE status LED
PoE
Solid green
Indicates the switching state.
Solid yellow
Indicates the PoE state.
1000Mbps RJ-45 port
status LED
1-10
Off
The port is not connected.
Solid green
The port is connected at 1000 Mbps.
Blinking green
The port is receiving or transmitting traffic at 1000
Mbps.
Solid yellow
The port is connected at 10/100 Mbps.
Blinking yellow
The port is receiving or transmitting traffic at
10/100 Mbps.
RJ45 port PoE status
LED
1-8
Off
PoE is not enabled.
Solid green
PoE is enabled. The port is operational.
Solid yellow
The PoE port is abnormally operational.
1000Mbps SFP port
status LED
11F-12F
Off
The port is not connected.
Solid green
The port is connected at 1000 Mbps.
Blinking green
The port is receiving or transmitting traffic at 1000
Mbps.

2 Preparation before Installation
2.1 Safety Suggestions
To avoid personal injury and equipment damage, please carefully read the safety suggestions before you install the
RG-S2910-H series switch.
The following safety suggestions do not cover all possible dangers.
2.1.1 Installation
Keep the chassis clean and free from any dust.
Do not place the equipment in a walking area.
Do not wear loose clothes or accessories that may be hooked or caught by the device during installation and
maintenance.
Turn off all power supplies and remove the power sockets and cables before installing or uninstalling the device.
2.1.2 Movement
Do not frequently move the device.
When moving the device, note the balance and avoid hurting legs and feet or straining the back.
Before moving the device, turn off all power supplies and dismantle all power modules.
2.1.3 Electricity
Observe local regulations and specifications when performing electric operations. Relevant operators must be
qualified.
Before installing the device, carefully check any potential danger in the surroundings, such as ungrounded power
supply, and damp/wet ground or floor.
Before installing the device, find out the location of the emergency power supply switch in the room. First cut off the
power supply in the case of an accident.
Try to avoid maintaining the switch that is powered-on alone.
Be sure to make a careful check before you shut down the power supply.
Do not place the equipment in a damp location. Do not let any liquid enter the chassis.
Any nonstandard and inaccurate electric operation may cause an accident such as fire or electrical shock, thus
causing severe even fatal damages to human bodies and equipment.
Direct or indirect touch through a wet object on high-voltage and mains supply may bring a fatal danger.

2.1.4 Static Discharge Damage Prevention
To prevent damage from static electricity, pay attention to the following:
Proper grounding of grounding screws on the back panel of the device. Use of a three-wire single-phase socket with
protective earth wire (PE) as the AC power socket.
Indoor dust prevention
Proper humidity conditions
2.1.5 Laser
The RG-S2910-H series switch supports varying models of optical modules sold on the market which are Class I laser
products. Improper use of optical modules may cause damage. Therefore, pay attention to the following when you use
them:
When a fiber transceiver works, ensure that the port has been connected with an optical fiber or is covered with a
dust cap, to keep out dust and avoid burning your eyes.
When the optical module is working, do not pull out the fiber cable and stare into the transceiver interface or you may
hurt your eyes.
Do not stare into any optical port under any circumstances, as this may cause permanent damage to your eyes.
2.2 Installation Site Requirements
To ensure the normal working and a prolonged durable life of the equipment, the installation site must meet the following
requirements.
2.2.1 Ventilation
For the RG-S2910-H, a sufficient space (at least 10 cm distances from both sides and the back plane of the cabinet)
should be reserved at the ventilation openings to ensure the normal ventilation. After various cables have been connected,
they should be arranged into bundles or placed on the cabling rack to avoid blocking the air inlets. It is recommended to
clean the switch at regular intervals (like once every 3 months). Especially, avoid dust from blocking the screen mesh on
the back of the cabinet.
2.2.2 Temperature and Humidity
To ensure the normal operation and prolong the service life of RG-S2910-H series switch, you should keep proper
temperature and humidity in the equipment room.
If the equipment room has temperature and humidity that do not meet the requirements for a long time, the equipment
may be damaged.
In an environment with high relative humidity, the insulating material may have bad insulation or even leak electricity.
Sometimes the materials may suffer from mechanical performance change and metallic parts may get rusted.
In an environment with low relative humidity, however, the insulating strip may dry and shrink. Static electricity may
occur easily and endanger the circuit on the equipment.