Ruijie RG-S2600G-I Series Instruction Manual

1
CLI Reference Guide
RG-S2600G-I Series Switches
RGOS 10.4(3b16)

2
RGOS®S2600G-I Series CLI Reference Guide
Revision No.: Version 10.4(3b16)
Date:
Copyright Statement
Ruijie Networks ©2000-2017
All rights reserved.
Without our written permission, this document may not be excerpted, reproduced, transmitted,
or otherwise in all or in part by any party in any means.
Exemption statement
This document is provided “as is”. The contents of this document are subject to change without
any notice. Please obtain the latest information through the Ruijie Networks website. Ruijie
Networks endeavors to ensure content accuracy and will not shoulder any responsibility for
losses and damages caused due to content omissions, inaccuracies or errors.

3
Preface
Version Description
This manual matches the software version RGOS®10.4(3b16).
Target Readers
This manual is intended for the following readers:
Network engineers
Technical salespersons
Network administrators
Conventions in this Document
1. Universal Format Convention
Arial: Arial with the point size 10 is used for the body.
Note: Aline is added respectively above and below the prompts such as caution
and note to separate them from the body.
Format of information displayed on the terminal: Courier New, point size 8,
indicating the screen output. User's entries among the information shall be
indicated with bolded characters.
2. Command Line Format Convention
Arial is used as the font for the command line. The meanings of specific formats
are described below:
Bold: Key words in the command line, which shall be entered exactly as they
are displayed, shall be indicated with bolded characters.
Italic: Parameters in the command line, which must be replaced with actual
values, shall be indicated with italic characters.
[ ]: The part enclosed with [ ] means optional in the command.
{ x | y | ... }: It means one shall be selected among two or more options.
[ x | y | ... ]: It means one or none shall be selected among two or more options.
//:Lines starting with an exclamation mark "//" are annotated.
3. Signs
Various striking identifiers are adopted in this manual to indicate the matters
that special attention should be paid in the operation, as detailed below:

4
Caution
Warning, danger or alert in the operation.
Note
Descript, prompt, tip or any other necessary supplement or
explanation for the operation.
Note
The port types mentioned in the examples of this manual may not
be consistent with the actual ones. In real network environments,
you need configure port types according to the support on various
products.
The display information of some examples in this manual may
include the information on other series products, like model and
description. The details are subject to the used equipments.

5

System Configuration
1. CLI Authorization Configuration Commands
2. Basic Configuration Management
3. HTTP Service Configuration Commands
4. UPGRADE Configuration Commands
5. LINE Configuration Commands
6. File System Configuration Commands
7. Configuration Commands of Configuration File Management
8. CPU-LOG Configuration Commands
9. Memory Configuration Commands
10.Syslog Configuration Commands
11.Cluster Management Configuration Commands
12.Redundancy Configuration Commands
13.SRM Configuration Commands
14.Hardware Entry Capacity Commands

CLI Reference Guide CLI Authorization Configuration Commands
CLIAuthorization Configuration
Commands
alias
You can use the alias command to configure an alias of a command in the global configuration mode. Use the no
form of the command to remove the alias of a specified command or all the aliases under one mode.
alias mode command-alias original-command
no alias mode command-alias
Parameter
description
Parameter
Description
mode
Mode of the command represented by the alias
command-alias
Alias of the command
original-command
Syntax of the command represented by the alias
Default
Settings
Some commands in the privileged EXEC mode have default alias
names.
Command
mode
Global configuration mode.
Usage
guidelines
The following table lists the default alias of the commands
in the privileged EXEC mode.
Alias
Actual Command
h
help
p
ping
s
show
u
undebug
un
undebug
The default alias cannot be deleted by the no alias exec
command.
By setting the alias, you can use a word to replace a
command. For example, you can create an alias to
represent the first part of a command, and then type the
rest part of the command.
The mode of the command represented by the alias is the
command mode existing in the current system. In the

CLI Reference Guide CLI Authorization Configuration Commands
global configuration mode, you can use alias ? to list all
the modes under which you can configure alias for
commands.
Ruijie(config)# alias ?
aaa-gs AAA server group mode
acl acl configure mode
bgp Configure bgp Protocol
config globle configure mode
......
The alias also has its help information that is displayed
after * in the following format:
*command-alias=original-command
For example, in the privileged EXEC mode, the default
alias sstands for show. You can enter s? to query the key
words beginning with sand the help information of the
alias.
Ruijie#s?
*s=show show start-chat start-terminal-service
If an alias represents more than one word, the command
will be displayed in brackets. For example, if you set sv
stand for show version in the privileged EXEC mode,
then:
Ruijie#s?
*s=show *sv="show version" show start-chat
start-terminal-service
The alias must begin with the first letter of the command.
The first letter of the command cannot be a space. The
space before the command cannot be used as a valid
alias.
Ruijie# s?
show start-chat start-terminal-service
The command alias also has its help information. For
example, if the alias ia represents ip address in the
interface configuration mode, then:
Ruijie(config-if)#ia ?
A.B.C.D IP address
dhcp IP Address via DHCP
Ruijie(config-if)# ip address
The above help information lists the parameters of ip
address and shows the actual command name.
You must enter an entire alias; otherwise it cannot be
recognized.
Use the show aliases command to show the aliases
setting in the system.

CLI Reference Guide CLI Authorization Configuration Commands
Examples
In the global configuration mode, use def-route to represent the
default route setting of ip route 0.0.0.0 0.0.0.0 192.168.1.1:
Ruijie# configure terminal
Ruijie(config)# alias config def-route ip route 0.0.0.0 0.0.0.0
192.168.1.1
Ruijie(config)#def-route?
*def-route="ip route 0.0.0.0 0.0.0.0 192.168.1.1"
Ruijie(config)# end
Ruijie# show aliases config
globle configure mode alias:
def-route ip route 0.0.0.0 0.0.0.0
192.168.1.1
Related
commands
Command
Description
show aliases
Show the aliases settings.
privilege
To attribute the execution rights of a command to a command level, use privilege in the global configuration
mode. The no form of this command recovers the execution rights of a command to the default setting.
privilege mode [all] [level level | reset ]command-string
no privilege mode [all] [level level ]command-string
Parameter
description
Parameter
Description
mode
CLI mode of the command to which the
execution rights are attributed.
all
Alias of the command
level
Specify the execution right levels (0–15) of a
command or sub-commands
reset
Restore the command execution rights to its
default level
command-string:
Command string to be authorized
Default
Settings
N/A.
Command
mode
Global configuration mode.

CLI Reference Guide CLI Authorization Configuration Commands
Usage
guidelines
The following table lists some key words that can be
authorized by command privilege in the CLI mode. The
number of command modes that can be authorized may
vary with different devices. In the global configuration
mode, you can use privilege ? to list all CLI command
modes that can be authorized.
Mode
Descripton
config
Global configuration mode.
exec
Privileged EXEC mode
interface
Interface configuration mode
ip-dhcp-pool
DHCP address pool configuration
mode
keychain
KeyChain configuration mode
keychain-key
KeyChain-key configuration
mode
time-range
Time-Range configuration mode
Examples
Set the password of CLI level 1 as test and attribute the reload rights
to reset the device:
Ruijie(config)#enable secret level 10test
Ruijie(config)#privilege exec level 1reload
After the above setting, you can access the CLI window as level-1
user to use the reload command:
Ruijie>reload ?
LINE Reason for reload
<cr>
You can use the key word all to attribute all sub-commands of reload
to level-1 users:
Ruijie(config)# privilege exec all level 1 reload
After the above setting, you can access the CLI window as level-1
user to use all sub commands of the reload command:
Ruijie>reload ?
LINE Reason for reload
at reload at a specific time/date
cancel cancel pending reload scheme