Ruijie S8600E Series Manual

Ruijie S8600E Series Switch Hardware
Installation

Contents
■Hardware Installation

Preface
Revision History
Audience
Ruijie business partners and customers who are responsible for configuring
and maintaining Ruijie wireless devices.
Note :
For more detail configuration , see configuration guide for each product . you can download
configuration guide at http://www.ruijienetworks.com
For more technical enquiry , you can visit Ruijie Service portal at http://case.ruijienetworks.com
. You need to sign up before submit a case.

Hardware Installation
Preparations Installing the Device to a Specified
Position Grounding Installing Power
Modules, Cards, and
Other Modules Check and
Confirmation
Note: Engineers who install such switches for the first time should read the RG-S8600E Series Switch
Hardware Installation and Reference Guide.
Safety notes:
Do not install the device in a moist place and keep the device away from liquid.
Do not wear loose clothes during installation, to avoid hooking components and causing damage. Therefore, fasten
clothes ribbons, scarves, and sleeves.
Place tools and components away from passageways to prevent collision.
Carefully check whether hidden risks exist in the work area, for example, the power supply is not grounded, the
power supply is not grounded securely, or the ground is wet.
Ambient requirements:
Temperature: 0°C to 50°C
Relative humidity: 10% to 90%
Cleanliness: ≤ 1.4 x 105(diameter of dust particles ≥ 5 μm)
Ventilation: 20 cm space is reserved on both sides and around the front and rear panels of the chassis, to ensure
smooth ventilation.
Anti-interference: far away from high-power (such as radars and radio transmitting stations), high-frequency, or
large-current devices

Hardware Installation
Pre-installation confirmation
The depth of the cabinet for accommodating an S8610E switch chassis must be greater than or equal to
100 cm. (80cm for S8607E and S8605E).
Whether the installation place meets device ventilation requirements: 20 cm space is reserved on both
sides and around the rear panel of the chassis.
Whether the installation place meets device temperature and relative humidity requirements: temperature
in the range of 0°C to 50°C and relative humidity in the range of 10% to 90%.
Whether the power supply is deployed at the installation place and current requirements are met:
Rated voltage range in the case of AC input: 100-240 V~, 50-60 Hz
Maximum voltage range in the case of AC input: 90-264 V~, 50-60 Hz
Rated voltage range in the case of DC input: -48 V DC
Maximum voltage range in the case of DC input: -36 V DC to -75 V DC
16 Anational standard-compliant power cable (applicable to 1600 W AC power supply) -- pay attention
to the power strip.
10 Anational standard-compliant power cable (applicable to 600 W AC power supply) -- pay attention
to the power strip.
50 ADC power cable (applicable to 1600 W DC power supply)
20 A DC power cable (applicable to 600 W DC power supply)
Whether network cables can be laid out at the installation place.
Preparations Installing the Device
to a Specified
Position Grounding Installing Power
Modules, Cards, and
Other Modules Check and
Confirmation

Hardware Installation
Unpacking
Required tools:
Flat-head screwdriver
Hammer
It is recommended to wear
gloves to prevent injuries.
Preparations Installing the Device to a Specified
Position Grounding Installing Power
Modules, Cards, and
Other Modules Check and
Confirmation
Unpacking instruction
Product information

Hardware Installation
Conveying: It is recommended that four persons convey the device simultaneously. The empty
chassis (including fans) weighs 104 kg for the S8610E , 30 kg for S807E and 20kg for S8605E.
Notes:
1. Do not hold panels, power module handles, or chassis handles during conveying. They cannot bear the
weight of the device. Holding these positions may cause damage and even personal injuries.
2. Before conveying the device, remove supervisor modules, service modules, and power modules from
the chassis to reduce the weight.
Preparations Installing the Device to a Specified
Position Grounding Installing Power
Modules, Cards, and
Other Modules Check and
Confirmation

Hardware Installation
Preparations Installing the Device to a Specified
Position Grounding Installing Power
Modules, Cards, and
Other Modules Check and
Confirmation
Installing cable management brackets
1. The RG-S8610E cable management bracket is mounted before delivery while the cable management bracket
is not mounted on the RG-S8605E and RG-S8607E before delivery.
S8605E S8607E

Hardware Installation
Installing cable management brackets
S8610E cabling figure:
4#:
Preparations Installing the Device to a Specified
Position Grounding Installing Power
Modules, Cards, and
Other Modules Check and
Confirmation
S8610E

Hardware Installation
The cabinet depth should be greater
than or equal to 1 m. The distance
between the column mounting bar of
the cabinet and the outer side of the
front cabinet door should be greater
than 180 mm and the thickness of the
front door should be smaller than 25
mm so as to ensure at least 155 mm
available space. In this way, after the
cable management bracket is installed
on the cabinet, the cabinet door can
be closed normally. For some
cabinets with the cabinet depth of 1
m, if the available distance between
the column mounting bar and the
cabinet door is smaller than 155 m,
the cabinet door cannot be closed and
the column mounting bar needs to be
moved backward.
Preparations Installing the Device to a Specified
Position Grounding Installing Power
Modules, Cards, and
Other Modules Check and
Confirmation