Ruijie XS-S1960-10GT2SFP-P-H Installation and operating manual

Ruijie XS-S1960-10GT2SFP-P-H Switches
Hardware Installation and Reference Guide V1.04

Copyright Statement
Ruijie Networks©2019
Ruijie Networks reserves all copyrights of this document. Any reproduction, excerption, backup, modification,
transmission, translation or commercial use of this document or any portion of this document, in any form or by any
means, without the prior written consent of Ruijie Networks is prohibited.
Exemption Statement
This document is provided “as is”. The contents of this document are subject to change without any notice. Please obtain
the latest information through the Ruijie Networks website. Ruijie Networks endeavors to ensure content accuracy and will
not shoulder any responsibility for losses and damages caused due to content omissions, inaccuracies or errors.

Preface
Thank you for using our products. This manual will guide you through the installation of the device.
This manual describes the functional and physical features and provides the device installation steps, hardware
troubleshooting, module technical specifications, and specifications and usage guidelines for cables and connectors.
Audience
It is intended for the users who have some experience in installing and maintaining network hardware. At the same time, it
is assumed that the users are already familiar with the related terms and concepts.
Obtaining Technical Assistance
Ruijie Networks Website: https://www.ruijienetworks.com/
Technical Support Website: https://ruijienetworks.com/support
Case Portal: https://caseportal.ruijienetworks.com
Community: https://community.ruijienetworks.com
Technical Support Email: [email protected]
Skype: [email protected]
Related Documents
Documents
Description
Configuration Guide
Describes network protocols and related mechanisms that
supported by the product, with configuration examples.
Command Reference
Describes the related configuration commands, including
command modes, parameter descriptions, usage guides, and
related examples.
Symbol Conventions
The symbols used in this document are described as below:
This symbol brings your attention to some helpful suggestions and references.
This symbol means that you must be extremely careful not to do some things that may damage the device or cause
data loss.

Declaration of Conformity
CE
Note: Operation of this equipment in a residential environment could cause radio interference.
FCC Class A
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment
is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own expense.

Hardware Installation and Reference Guide Product Overview
1Product Overview
The XS-S1960-10GT2SFP-P-H switch is a next-generation intelligent switch that features high performance, high
security, multiple services and ease of use to meet the needs of the current networks. The XS-S1960-10GT2SFP-P-H
switch can provide the complete end-to-end Quality of Service (QoS), flexible and abundant security policies and
policy-based network management for various networks. It is greatly ideal for such applications as campus network,
enterprise network, government network, service network, residential broadband access and business building network,
providing high-speed, high-efficiency, secure and intelligent access solutions.
Table 1-1 XS-S1960-10GT2SFP-P-H
Model
10/100/1000 Base-T
Auto-sensing Ethernet Port
SFP+
Port
1000Base-X
SFP Port
Console
Port
USB
Port
Pluggable
Power
Slot
XS-S1960-10GT2SFP-P-H
10 (Ports 1-8 are PoE capable)
\
2
1
\
\
The SFP ports only support 1000base-X modules.
1000Base-T is compatible with 100Base-TX and 10Base-T in the downlink direction.
The PoE ports support IEEE 802.af/at PoE.
1.1 XS-S1960-10GT2SFP-P-H
Technical Specifications
Model
XS-S1960-10GT2SFP-P-H
CPU
Built-in CPU, single-core processor, 400MHz
Flash Memory
256M
SDRAM
DDRIII 512MB
Optical Module
Supports 1000base-X only. For details, see Appendix B.
The supported module type may change at any time. Consult us for the latest information.
SFP Port
Supports 1000Base-X SFP modules.
Power Supply
AC input
Rated voltage range: 100V to 240V
Maximum voltage range: 90V to 264V
Frequency: 50/60 Hz
Rated current: 2A
HVDC input
Voltage range: 192V to 290V
Current range: 1.0A to 0.4A
Earth Leakage
Current
≤1.5mA

Hardware Installation and Reference Guide Product Overview
EEE
Supported
PoE
Ports 1-8 are PoE-capable with the maximum power output of 30W.
The maximum output power of PoE/PoE+ is 125W.
PoE ports support IEEE 802.af/at PoE.
The available number of PDs is determined by PSE output power and PD input power in
practice.
Power
Consumption
Less than 20W with no PoE load
Less than 165W with PoE full load
Operating
Temperature
0℃to 45℃
Storage
Temperature
-40℃to 70℃
Operating Humidity
10% to 90%
Storage Humidity
5% to 95%
Fan
Fanless design
Temperature
Warning
Supported
EMCStandards
GB9254-2008
EN 300 386
EN 61000-3-2
EN 61000-3-3
EN 61000-4-2
EN 61000-4-3
EN 61000-4-4
EN 61000-4-5
EN 61000-4-6
EN 61000-4-11
EN 55022
EN 55024
EN 61000-4-8
Security Standards
GB4943-2011
EN60950-1
IEC60950-1
Dimensions
(W x D x H)
340 mm x 260 mm x 44 mm
Weight
≤2.5 kg (with package)
The XS-S1960-10GT2SFP-P-H switch is a class A product. In a domestic environment, this product may cause radio
interference in which case the user may be required to take adequate measures.
Product Appearance
On the front panel, the XS-S1960-10GT2SFP-P-H Ethernet switch provides 10 10/100/1000Base-T Ethernet ports, 2 SFP
ports, and 1 Console port. On the back panel, it provides AC power ports.

Hardware Installation and Reference Guide Product Overview
Figure 1-1 Appearance of XS-S1960-10GT2SFP-P-H
Front Panel
Figure 1-2 Front Panel of XS-S1960-10GT2SFP-P-H
Note:
1. System status LED
2. PoE status LED
3. 10/100/1000Base-T auto-sensing Ethernet
port
4. Copper port status LED
5. Copper port status LED
6. Fiber port status LED
7. PoE Mode Switch-Over Button
8. Console port
9. 10/100/1000Base-T auto-sensing Ethernet port
10. 1000Base-X SFP port
11. Reset Button
Long press PoE Mode Switch-Over Button for above 2 seconds to switch the display mode between PoE mode and
port rate mode.

Hardware Installation and Reference Guide Product Overview
Back Panel
Figure 1-3 Back Panel of XS-S1960-10GT2SFP-P-H
Note:
1. Grounding pole
2. Ventilation openings
Power Supply
The XS-S1960-10GT2SFP-P-H switch adopts AC or HVDC power input.
AC input
Rated voltage range: 100V to 240V
Maximum voltage range: 90V to 264V
Frequency range: 50/60 Hz
Rated current: 2A
Power cord specification: 10A
HVDC input
Voltage range: 192V to 290V
Current range: 0.4A to 1.0A
Heat Dissipation
The XS-S1960-10GT2SFP-P-H adopts fanless design, thereby ensuring normal function of the device in the specified
environment. 10 cm distance space should be reserved at both sides and the back plane of the cabinet to allow air
circulation. It is recommended to clean the device once every 3 months to avoid dust from blocking vents. Figure 1-4
shows the flow scheme of heat dissipation.
Figure 1-4 Flow Scheme of Heat Dissipation

Hardware Installation and Reference Guide Product Overview
LEDs
LED
Panel Identification
State
Meaning
Off
The switch is not receiving power.
Blinking green
The system is being initialized.
Continuous blinking indicates errors.
Solid green
The switch is operational.
Solid yellow
Temperature warning
Check the working environment of the switch
immediately.
System status LED
Status
Solid red
The switch is faulty.
Solid green
Indicates the switching state.
PoE status LED
PoE
Solid yellow
Indicates the PoE state.
Off
The port is not connected.
Solid green
The port is connected at 1000 Mbps.
1000Mbps RJ-45 port
status LED
1-10
Blinking green
The port is receiving or transmitting traffic at 1000
Mbps.

Hardware Installation and Reference Guide Product Overview
Solid yellow
The port is connected at 10/100 Mbps.
Blinking yellow
The port is receiving or transmitting traffic at
10/100 Mbps.
Off
PoE is not enabled.
Solid green
PoE is enabled. The port is operational.
RJ45 port PoE status
LED
1-8
Solid yellow
The PoE port is abnormally operational.
Off
The port is not connected.
Solid green
The port is connected at 1000 Mbps.
1000Mbps SFP port
status LED
11F-12F
Blinking green
The port is receiving or transmitting traffic at 1000
Mbps.