Ruijie RG-S1808 Installation and operating manual

Hardware Installation and Reference Guide
RG-S1800 Series Switch
RG-S1800G Series Switch
RG-S1800-P Series Switch
RG-S1800G-P Series Switch

Copyright Statement
Ruijie Networks©2017
Ruijie Networks reserves all copyrights of this document. Any reproduction, excerption, backup, modification,
transmission, translation or commercial use of this document or any portion of this document, in any form or by any
means, without the prior written consent of Ruijie Networks is prohibited.
Exemption Statement
This document is provided “as is”. The contents of this document are subject to change without any notice. Please
obtain the latest information through the Ruijie Networks website. Ruijie Networks endeavors to ensure content
accuracy and will not shoulder any responsibility for losses and damages caused due to content omissions,
inaccuracies or errors.

Preface
Thank you for using our products. This manual will guide you through the installation of the device.
This manual describes the functional and physical features and provides the device installation steps, hardware
troubleshooting, module technical specifications, and specifications and usage guidelines for cables and connectors.
Audience
It is intended for the users who have some experience in installing and maintaining network hardware. At the same time,
it is assumed that the users are already familiar with the related terms and concepts.
Obtaining Technical Assistance
Ruijie Networks Website: http://www.ruijienetworks.com/
Service Email: [email protected]
Technical Support: http://www.ruijienetworks.com/service.aspx
Technical Support Hotline: [phone]
Symbol Conventions
Means reader take note. Notes contain helpful suggestions or references.
Means reader be careful. In this situation, you might do something that could result in equipment damage or loss
of data.

Hardware Installation and Reference Guide Product Overview
Table of Contents
1 Product Overview...................................................................................................................................................- 6 -
1.1 RG-S1800 Series Switch.......................................................................................................................- 7 -
1.1.1 RG-S1808.....................................................................................................................................- 7 -
1.1.2 RG-S1826.....................................................................................................................................- 9 -
1.2 RG-S1800G Series Switch..................................................................................................................- 11 -
1.2.1 RG-S1808G................................................................................................................................- 11 -
1.2.2 RG-S1818G................................................................................................................................- 14 -
1.2.3 RG-S1826G................................................................................................................................- 16 -
1.2.4 Module........................................................................................................................................- 19 -
1.3 RG-S1800-P Series Switch.................................................................................................................- 19 -
1.3.1 RG-S1809-P ...............................................................................................................................- 19 -
1.4 RG-S1800G-P Series Switch..............................................................................................................- 21 -
1.4.1 RG-S1826G-P ............................................................................................................................- 21 -
1.4.2 Module........................................................................................................................................- 24 -
2 Preparation before Installation.............................................................................................................................- 25 -
2.1 Safety Suggestions .............................................................................................................................- 25 -
2.1.1 Safety Precautions for Installing the System...............................................................................- 25 -
2.1.2 Movement Safety........................................................................................................................- 25 -
2.1.3 Electric Safety.............................................................................................................................- 25 -
2.1.4 Static Discharge Damage Prevention.........................................................................................- 26 -
2.1.5 Laser Safety................................................................................................................................- 26 -
2.2 Installation Site Requirements.............................................................................................................- 26 -
2.2.1 Ventilation Requirements............................................................................................................- 26 -
2.2.2 Temperature and Humidity Requirements..................................................................................- 26 -
2.2.3 Cleanness Requirements............................................................................................................- 27 -
2.2.4 EMI .............................................................................................................................................- 27 -
2.2.5 System Grounding Requirements...............................................................................................- 28 -
2.2.6 Lightning Resistance Considerations..........................................................................................- 29 -
2.2.7 EMI Consideration ......................................................................................................................- 30 -
2.3 Requirements of Installation Tools......................................................................................................- 30 -
3 Product Installation ..............................................................................................................................................- 31 -
3.1 Installation Procedure..........................................................................................................................- 31 -
3.2 Confirmations before Installation.........................................................................................................- 31 -
3.3 Precautions.........................................................................................................................................- 31 -
3.4 Installing the RG-S1800 Series...........................................................................................................- 32 -
3.4.1 Mounting the Switch in the Rack.................................................................................................- 32 -
3.4.2 Mounting the Switch on the Wall.................................................................................................- 33 -
3.4.3 Mounting the Switch to a Workbench..........................................................................................- 34 -
3.5 Installing the RG-S1800G Series........................................................................................................- 34 -
3.5.1 Mounting the Switch in the Rack.................................................................................................- 34 -
3.5.2 Mounting the Switch on the Wall.................................................................................................- 35 -

Hardware Installation and Reference Guide Product Overview
3.5.3 Mounting the Switch to a Workbench..........................................................................................- 36 -
3.6 Installing the RG-S1800-P Series .......................................................................................................- 37 -
3.6.1 Mounting the Switch to a Workbench..........................................................................................- 37 -
3.6.2 Mounting the Switch on the Wall.................................................................................................- 38 -
3.7 Installing the RG-S1800G-P Series.....................................................................................................- 40 -
3.7.1 Mounting the Switch in the Rack.................................................................................................- 40 -
3.7.2 Mounting the Switch on the Wall.................................................................................................- 40 -
3.7.3 Mounting the Switch to a Workbench..........................................................................................- 41 -
3.8 Connecting the Power Cord ................................................................................................................- 42 -
3.9 Checking after Installation...................................................................................................................- 43 -
4 Maintenance and Troubleshooting.......................................................................................................................- 44 -
4.1 General Troubleshooting Procedure ...................................................................................................- 44 -
4.2 Common Faults...................................................................................................................................- 44 -
Appendix A: Connectors and Connection Media..............................................................................................................46
Appendix B Mini-GBIC Modules...................................................................................................................................- 48 -

Hardware Installation and Reference Guide Product Overview
1 Product Overview
Thank you for using Ruijie Networks RG-S18 series Ethernet switches.
The RG-S1800 series switches are unmanaged 100M switches released by Ruijie Networks. Some of the switches
provide GE uplink ports, powerful switching performance, and cost-effective GE port-based uplink capability.
The RG-S1800G series switches are full GE switches released by Ruijie Networks. With powerful switching capability
and cost-effective full GE copper cable ports, the switches fully meet users' requirements for high-bandwidth data
communication, dense high-speed access server clusters, and GE backbone service network construction.
The RG-S1800-P series switches are PoE-capable 100M Ethernet switches released by Ruijie Networks. Some of the
switches provide 100M uplink ports, powerful switching performance, and cost-effective 100M port-based uplink
capability. In addition, some other switches provide GE uplink ports, powerful switching performance, and cost-effective
GE port-based uplink capability. This series of switches are characterized by high performance, high security, support
for multiple services, and ease of use, and provide brand new technical solutions for users. Each port of the switches
can provide high bandwidth and supply power to wireless APs and IP cameras. The switches support full-/half-duplex
mode, and enable low-cost and high-performance network solutions.
The RG-S1800G-P series switches are full GE PoE switches released by Ruijie Networks. The switches are
characterized by high performance, high security, support for multiple services, and ease of use, and enable new
technical solutions for users. Each port of the switches can provide high bandwidth and supply power to wireless APs
and IP cameras. The switches support full-/half-duplex mode, and enable low-cost and high-performance network
solutions.
Some models of the S18 series switches are capable of independent flow control, which prevents data packet loss
during data transmission.
RG-S1800 Series Switch
Model
10/100BASE-T
Auto-sensing Ethernet
Port
Combo Ports
10/100/1000BASE-T
Auto-sensing Ethernet
Port
1000BASE-X SFP Port
RG-S1808
8
N/A
N/A
RG-S1826
24
2
2
Combo port consists of one 1000BASE-X SFP port and one 10/100/1000BASE-T auto-sensing Ethernet port. That
is, only one port of them is available at a particular time.
RG-S1800G Series Switch
Model
10/100/1000BASE-T Auto-sensing Ethernet
Port
1000BASE-X SFP Port
RG-S1808G
8
N/A
RG-S1818G
16
2

Hardware Installation and Reference Guide Product Overview
RG-S1826G
24
2
RG-S1800-P Series Switch
Model
10/100BASE-T Auto-sensing
Ethernet Port
10/100/1000BASE-T
Auto-sensing Ethernet Port
PoE Port
RG-S1809-P
8
1
8
RG-S1800G-P Series Switch
Model
10/100/1000BASE-T
Auto-sensing Ethernet Port
PoE Port
1000BASE -X SFP Port
RG-S1826G-P
24
24
2
1.1 RG-S1800 Series Switch
1.1.1 RG-S1808
Technical Specifications
Model
RG-S1808
Ports
8-port 10/100BASE-T
Power Supply
DC input:
DC 5V/550mA
Rated current: 550mA
Max voltage range: 90V to 290V~
PoE
Not supported
Power Consumption
1.5W(Max)
Operating
Temperature
0ºC to 50ºC (32ºF to 122ºF)
Storage Temperature
-40ºC to +70ºC (-40ºF to 158ºF)
Operating Humidity
10% to 90% RH non-condensing
Storage Humidity
5% to 90% RH non-condensing
Fan
N/A
EMC Standards
EN55032(Class B)
Dimensions (W×D×H)
140 mm x 76 mm x 27 mm
Switching
Capacity(Gbps)
1.6Gbps
Product Appearance
The front panel of RG-S1808 Ethernet switch provides a Power Status LED indicator and Link/ACT Status LED
indicators. The rear panel provides eight 10/100BASE-T Ethernet ports and one DC power input port. Figure 1-1 shows
the appearance of the RG-S1808.
Figure 1-1 Appearance of RG-S1808

Hardware Installation and Reference Guide Product Overview
Front Panel
Figure 1-2 Front Panel of RG-S1808
Note
1. Power status indicator
2. 10/100BASE-T Link/ACT indicator
Rear Panel
Figure1-3 Rear Panel of RG-S1808
Note
1. 10/100BASE-T ports
2. DC power input port
Power Supply
The RG-S1808 switch can be powered with DC power.
DC input: DC 5V/550mA
Heat Dissipation

Hardware Installation and Reference Guide Product Overview
The RG-S1808 switch is designed with no fans. To ensure good dissipation, sufficient space (10 cm distance from both
sides and the back panel of the chassis) should be reserved for ventilation. Dust the device every three months to avoid
blocking the ventilation openings.
LED Indicator
Indicator
Faceplate Marker
Status
Indication
Power indicator
PWR
Off
The switch is powered down.
On
The switch is powered on.
Ethernet port indicator
1-8
Off
The port is NOT connected.
Solid green
The port is connected.
Blinking green
The port is transmitting or receiving data.
1.1.2 RG-S1826
Technical Specifications
Model
RG-S1826
Ports
24-port 10/100BASE-T
2 combo ports
SFP Type
Ethernet Gigabit:
Mini-GBIC-SX
Mini-GBIC-LX
Mini-GBIC-LH40
Mini-GBIC-ZX50
Mini-GBIC-ZX80
Mini-GBIC-ZX100
1000Base-T:
Mini-GBIC-GT
The supported module type may change at any time. Consult us for the detailed change
information.
SFP Ports
Support 1000BASE-X
Power Supply
AC input:
Rated voltage range: 100V to 240V
Max voltage range: 90V to 290V
Frequency: 50/60Hz
Rated current: 0.5A
PoE
Not supported

Hardware Installation and Reference Guide Product Overview
Power Consumption
12W(Max)
Operating
Temperature
0ºC to 50ºC (32ºF to 122ºF)
Storage Temperature
-40ºC to +70ºC (-40ºF to 158ºF)
Operating Humidity
10% to 90% RH non-condensing
Storage Humidity
5% to 90% RH non-condensing
Fan
N/A
EMC Standards
EN55032(Class A)
Dimensions (W×D×H)
440 mm x 205 mm x 44 mm
Switching Capacity
8.8Gbps
Product Appearance
The front panel of RG-S1826 Ethernet switch provides 24 10/100BASE-T Ethernet ports, two Gigabit combo ports. The
rear panel provides an AC power input port and a grounding connector.
Figure 1-4 Appearance of RG-S1826
Front Panel
Figure 1-5 Front Panel of RG-S1826
Note
1. Power status indicator
2. 10/100BASE-T Link/ACT indicator
3.10/100/1000BASE-T Link/ACT
indicator
4. 10/100BASE-T Ethernet port
5. 10/100/1000BASE-T Ethernet port
6. 1000BASE-X SFP port
Rear Panel
Figure1-6 Rear Panel of RG-S1826

Hardware Installation and Reference Guide Product Overview
Note
1. Grounding connector
2. AC power input port
Power Supply
The RG-S1826 switch can be powered with AC power.
Rated voltage range: 100V to 240V
Max voltage range: 90V to 290V
Frequency: 50/60Hz
Rated current: 0.5A
Power Cord Requirements: 10A
Heat Dissipation
The RG-S1826 switch is designed with no fans. To ensure good dissipation, sufficient space (10 cm distance from both
sides and the back panel of the chassis) should be reserved for ventilation. Dust the device every three months to avoid
blocking the ventilation openings.
LED Indicator
Indicator
Faceplate Marker
Status
Indication
Power indicator
PWR
Off
The switch is powered down.
On
The switch is powered on.
Ethernet port indicator
1-24
Off
The port is NOT connected.
Solid green
The port is connected.
Blinking green
The port is transmitting or receiving data.
Combo port indicator
25 T/S
26 T/S
Off
The port is NOT connected.
Solid green
The port is connected.
Blinking green
The port is transmitting or receiving data.
1.2 RG-S1800G Series Switch
1.2.1 RG-S1808G
Technical Specifications
Model
RG-S1808G

Hardware Installation and Reference Guide Product Overview
Ports
8-port 10/100/1000 BASE-T
Power Supply
AC input:
Rated voltage range: 100V to 240V
Max voltage range: 90V to 290V
Frequency: 50/60Hz
Rated current: 0.3A
PoE
Not supported
Power Consumption
2.5W(Max)
Operating Temperature
0ºC to 50ºC (32ºF to 122ºF)
Storage Temperature
-40ºC to +70ºC (-40ºF to 158ºF)
Operating Humidity
10% to 90% RH non-condensing
Storage Humidity
5% to 90% RH non-condensing
Fan
N/A
EMC Standards
EN55032(Class B)
Dimensions (W×D×H)
220 mm x 160 mm x 44 mm
Switching
Capacity(Gbps)
16Gbps
Product Appearance
The front panel of RG-S1808G Ethernet switch provides eight 10/100/1000Mbps Ethernet ports. The rear panel
provides an AC power input port and a grounding connector.
Figure 1-7 Appearance of RG-S1808G
Front Panel
Figure 1-8 Front Panel of RG-S1808G

Hardware Installation and Reference Guide Product Overview
Note
1. Power status indicator
2. 10/100/1000BASE-T Link/ACT/Speed
indicator
3. Power cord retention clip
Rear Panel
Figure1-9 Rear Panel of RG-S1808G
Note
1. Grounding connector
2. AC power input port
Power Supply
The RG-S1808G switch can be powered with AC power.
Rated voltage range: 100V to 240V
Max voltage range: 90V to 290V
Frequency: 50/60Hz
Rated current: 0.3A
Power cord requirement: 10A
Heat Dissipation
The RG-S1808G switch is designed with no fans. To ensure good dissipation, sufficient space (10 cm distance from
both sides and the back panel of the chassis) should be reserved for ventilation. Dust the device every three months to
avoid blocking the ventilation openings.
LED Indicator
Indicator
Faceplate
Marker
Status
Indication
Power indicator
PWR
Off
The switch is powered down.
On
The switch is powered on.
Ethernet port indicator
1-8
Off
The port is NOT connected.
Solid orange
The port is connected at 10/100 Mbps.

Hardware Installation and Reference Guide Product Overview
Blinking orange
The port is receiving or transmitting
traffic at 10/100 Mbps.
Solid green
The port is connected at 1000 Mbps.
Blinking green
The port is receiving or transmitting
traffic at 1000 Mbps.
1.2.2 RG-S1818G
Technical Specifications
Model
RG-S1818G
Ports
16-port 10/100/1000BASE-T
2-port 1000BASE-X SFP
SFP Type
Ethernet Gigabit:
Mini-GBIC-SX
Mini-GBIC-LX
Mini-GBIC-LH40
Mini-GBIC-ZX50
Mini-GBIC-ZX80
Mini-GBIC-ZX100
1000Base-T:
Mini-GBIC-GT
The supported module type may change at any time. Consult us for the detailed
change information.
SFP Ports
Support 1000Base-X
Power Supply
AC input:
Rated voltage range: 100V to 240V
Max voltage range: 90V to 290V
Frequency: 50/60Hz
Rated current: 0.5A
PoE
Not supported
Power Consumption
9W(max)
Operating
Temperature
0ºC to 50ºC (32ºF to 122ºF)
Storage Temperature
-40ºC to +70ºC (-40ºF to 158ºF)
Operating Humidity
10% to 90% RH non-condensing
Storage Humidity
5% to 90% RH non-condensing
Fan
N/A
EMC Standards
EN55032(Class A)
Dimensions (W×D×H)
440 mm x 205 mm x 44 mm

Hardware Installation and Reference Guide Product Overview
Switching
Capacity(Gbps)
36Gbps
Product Appearance
The front panel of RG-S1818G Ethernet switch provides 16 10/100/1000BASE-T Ethernet ports, two 1000BASE-X SFP
ports. The rear panel provides an AC power input port and a grounding connector.
Figure 1-10 Appearance of RG-S1818G
Front Panel
Figure 1-11 Front Panel of RG-S1818G
Note
1. Power status indicator
2. 10/100/1000BASE-T Link/ACT/Speed
indicator
3.1000BASE-X SFP port indicator
4. 10/100/1000BASE-T Ethernet port
5. 1000BASE-X SFP port
Rear Panel
Figure1-12 Rear Panel of RG-S1818G
Note
1. Grounding connector
2. AC power input port
Power Supply

Hardware Installation and Reference Guide Product Overview
RG-S1818G switch can be powered with AC power.
Rated voltage range: 100V to 240V
Max voltage range: 90V to 290V
Frequency: 50/60Hz
Rated current: 0.5A
Power cord requirement: 10A
Heat Dissipation
The RG-S1818G switch is designed with no fans. To ensure good dissipation, sufficient space (10 cm distance from
both sides and the back panel of the chassis) should be reserved for ventilation. Dust the device every three months to
avoid blocking the ventilation openings.
LED Indicator
Indicator
Faceplate
Marker
Status
Indication
Power indicator
PWR
Off
The switch is powered down.
On
The switch is powered on.
Ethernet port indicator
1-16
Off
The port is NOT connected.
Solid orange
The port is connected.
Blinking orange
The port is connected at 10/100 Mbps.
Solid green
The port is connected at 1000 Mbps.
Blinking green
The port is receiving or transmitting
traffic at 1000 Mbps.
SFP port indicator
SFP1, SFP2
Off
The port is NOT connected.
Solid orange
The port is connected at 100 Mbps.
Blinking orange
The port is receiving or transmitting
traffic at 100 Mbps.
Solid green
The port is connected at 1000 Mbps.
Blinking green
The port is receiving or transmitting
traffic at 1000 Mbps.
1.2.3 RG-S1826G
Technical Specifications
Model
RG-S1826G
Ports
24-port 10/100/1000BASE-T
2-port 1000BASE-X SFP
SFP Type
Ethernet Gigabit:
Mini-GBIC-SX
Mini-GBIC-LX
Mini-GBIC-LH40
Mini-GBIC-ZX50

Hardware Installation and Reference Guide Product Overview
Mini-GBIC-ZX80
Mini-GBIC-ZX100
1000Base-T:
Mini-GBIC-GT
The supported module type may change at any time. Consult us for the detailed change
information.
SFP Ports
Support 1000Base-X
Power Supply
AC input:
Rated voltage range: 100V to 240V
Max voltage range: 90V to 290V
Frequency: 50/60Hz
Rated current: 0.5A
PoE
Not supported
Power Consumption
13W(max)
Operating
Temperature
0ºC to 50ºC (32ºF to 122ºF)
Storage Temperature
-40ºC to +70ºC (-40ºF to 158ºF)
Operating Humidity
10% to 90% RH non-condensing
Storage Humidity
5% to 90% RH non-condensing
Fan
N/A
EMC Standards
EN55032(Class A)
Dimensions (W×D×H)
440 mm x 205 mm x 44 mm
Switching
Capacity(Gbps)
52Gbps
Product Appearance
The front panel of RG-S1826G Ethernet switch provides 24 10/100/1000BASE-T Ethernet ports and two 1000BASE-X
SFP ports. The rear panel provides an AC power input port and a grounding connector
Figure 1-13 Appearance of RG-S1826G
Front Panel
Figure 1-14 Front Panel of RG-S1826G

Hardware Installation and Reference Guide Product Overview
Note
1. Power status indicator
2. 10/100/1000BASE-T Link/ACT/Speed
indicator
3. 1000BASE-T SFP port indicator
4. 10/100/1000BASE-T Ethernet port
5.1000BASE-X SFP port
Rear Panel
Figure1-15 Rear Panel of RG-S1826G
Note
1. Grounding connector
2. AC power input port
Power Supply
RG-S1826G switch can be powered with AC power:
Rated voltage range: 100V to 240V
Max voltage range: 90V to 290V
Frequency: 50/60Hz
Rated current: 0.5A
Power Cord Requirements: 10A
Heat Dissipation
RG-S1826G switch is designed with no fans. To ensure good dissipation, sufficient space (10 cm distance from both
sides and the back panel of the chassis) should be reserved for ventilation. Dust the device every three months to avoid
blocking the ventilation openings.
LED indicator
Indicator
Faceplate
Marker
Status
Indication
Power indicator
PWR
Off
The switch is powered down.
On
The switch is powered on.
Ethernet port indicators
1-24
Off
The port is NOT connected.

Hardware Installation and Reference Guide Product Overview
Solid orange
The port is connected at 10/100 Mbps.
Blinking orange
The port is receiving or transmitting traffic
at 10/100 Mbps.
Solid green
The port is connected at 1000 Mbps.
Blinking green
The port is receiving or transmitting traffic
at 1000 Mbps.
SFP port indicators
SFP1, SFP2
Off
The port is NOT connected.
Solid orange
The port is connected at 100 Mbps.
Blinking orange
The port is receiving or transmitting traffic
at 100 Mbps.
Solid green
The port is connected at 1000 Mbps.
Blinking green
The port is receiving or transmitting traffic
at 1000 Mbps.
1.2.4 Module
The RG-S1800G series switches support the following modules: M3000E-02SFP/GT and M3000E-STACK.
M3000E-02SFP/GT can be used to extend two SFP ports.
1.3 RG-S1800-P Series Switch
1.3.1 RG-S1809-P
Technical Specifications
Model
RG-S1809-P
Ports
8-port 10/100BASE-T
1-port 10/100/1000BASE-T Uplink
Power Supply
DC input:
DC 53.5V/2.3A
Rated current: 2.3A
Max voltage range: 90V to 290V
PoE
Support
Power Consumption
120W(Max)
Operating
Temperature
0ºC to 50ºC (32ºF to 122ºF)
Storage Temperature
-40ºC to +70ºC (-40ºF to 158ºF)
Operating Humidity
10% to 90% RH non-condensing
Storage Humidity
5% to 90% RH non-condensing
Fan
N/A
EMC Standards
EN55032(Class B)
Dimensions (W×D×H)
190 mm x 100 mm x 28 mm
Switching Capacity
3.6Gbps

Hardware Installation and Reference Guide Product Overview
Product Appearance
The front panel of RG-S1809-P Ethernet switch provides a power LED indicator, PoE LED indicators and Link/ACT LED
indicators, 8-port 10/100BASE-T Ethernet ports and one Gigabit uplink port.
Figure 1-16 Appearance of RG-S1809-P
Front Panel
Figure 1-17 Front Panel of RG-S1809-P
Note
1. Power status indicator
2. 10/100BASE-T Link/ACT
indicator(1-8),10/100/1000BASE-T
Link/ACT indicator(Uplink)
3. PoE Status LED indicator
4. 10/100 BASE-T Ethernet port
5.10/100/1000 BASE-T Ethernet port
Rear Panel
Figure1-18 Rear Panel of RG-S1809-P
Note
1. Grounding connector
2. DC power input port
Power Supply
RG-S1809-P switch can be powered with DC power.