Ruijie RG-S2928G-E Installation and operating manual

RG-S2900G-E Series Switch
Hardware Installation and Reference Guide V1.25

Copyright Statement
Ruijie Networks©2017
Ruijie Networks reserves all copyrights of this document. Any reproduction, excerption, backup, modification,
transmission, translation or commercial use of this document or any portion of this document, in any form or by any means,
without the prior written consent of Ruijie Networks is prohibited.
Exemption Statement
This document is provided “as is”. The contents of this document are subject to change without any notice. Please obtain
the latest information through the Ruijie Networks website. Ruijie Networks endeavors to ensure content accuracy and will
not shoulder any responsibility for losses and damages caused due to content omissions, inaccuracies or errors.

Preface
Thank you for using our products. This manual will guide you through the installation of the device.
This manual describes the functional and physical features and provides the device installation steps, hardware
troubleshooting, module technical specifications, and specifications and usage guidelines for cables and connectors.
Audience
It is intended for the users who have some experience in installing and maintaining network hardware. At the same time, it
is assumed that the users are already familiar with the related terms and concepts.
Obtaining Technical Assistance
Ruijie Networks Website: http://www.ruijienetworks.com/
Service Email: [email protected]
Technical Support: http://www.ruijienetworks.com/service.aspx
Technical Support Hotline: [phone]
Related Documents
Documents
Description
Configuration Guide
Describes network protocols and related mechanisms that supported by the
product, with configuration examples.
Command Reference
Describes the related configuration commands, including command modes,
parameter descriptions, usage guides, and related examples.
Symbol Conventions
Means reader take note. Notes contain helpful suggestions or references.
Means reader be careful. In this situation, you might do something that could result in equipment damage or loss of
data.

1 Product Overview
RG-S2900G-E Series switch is a next-generation security and intelligent switch that features high performance, high
security, multiple services and ease of use to meet the needs of the current networks. The RG-S2900G-E switch can
provide the complete end-to-end Quality of Service (QoS), flexible and abundant security policies and policy-based
network management for various networks. They are the desired access devices for such applications as campus network,
enterprise network, government network, service network, residential broadband access and business building network,
providing high-speed, high-efficiency, secure and intelligent access solutions.
Table 1-1 RG-S2900G-E Series
Model
10/100/1000 Base-T Adaptive Ethernet Port
SFP Port
Console Port
Extension Module Slot
RG-S2928G-E
24
4
1
N/A
RG-S2952G-E
48
4
1
N/A
RG-S2928G-12P
24
4
1
N/A
RG-S2928G-24P
24
4
1
N/A
The four SFP ports support 100Base-FX/1000Base-X/1000Base-T, and the two SFP ports with larger port number
(27F and 28F for the S2928G Series, and 51F and 52F for the S2952 Series) also support 2.5 G stack modules.
Only the four SFP ports of the RG-S2928G-E V2.00 and RG-S2952G-E V2.00 and later, RG-S2928G-12P and
RG-S2928G-24P support 100Base-FX.
1.1 RG-S2928G-E
Technical Specifications
Model
RG-S2928G-E
CPU
Single-core CPU, clock speed of 600M
BOOTROM
8M
Flash Memory
128M
SDRAM
DDRII 128MB
Supported SFP
Type
Gigabit Ethernet:
MINI-GBIC-SX-MM850
MINI-GBIC-LX-SM1310
MINI-GBIC-LH40-SM1310
MINI-GBIC-ZX50-SM1550
MINI-GBIC-ZX80-SM1550
MINI-GBIC-ZX100-SM1550
Fast Ethernet:
FE-SFP-LX-MM1310
FE-SFP-LH15-SM1310

1000Base-T:
Mini-GBIC-GT
2.5G stack module:
GE-SFP-STACK1.6M
The supported module type may change at any time. Consult us for the detailed change
information.
Only the four SFP ports of the RG-S2928G-E V2.00 and later support fast Ethernet SFP
modules.
SFP Port
Support 1000Base-X, 1000Base-T and 2.5 G stacked SFP module
Only the four SFP ports of the RG-S2928G-E V2.00 and later support 100Base-FX.
USB Port
One Type-A USB2.0 interface
Power Supply
AC input:
Rated voltage range: 100 V to 240 V
Maximum voltage range: 90 V to 264 V
Frequency: 50/60 Hz
Rated current: 2A
HVDC input:
Maximum voltage range: 192 V to 290 V
Rated current: 0.2 A to 0.12 A
EEE
Not supported on the RG-S2928G-E V1.00 and later.
Supported on the RG-S2928G-E V2.00 and later.
PoE
Not supported.
Power
Consumption
Less than 33 W on the RG-S2928G-E V1.00 and later.
Less than 27 W on the RG-S2928G-E V2.00 and later.
Working
Temperature
0ºC to 50ºC
Storage
Temperature
-40ºC to 70ºC
Working Humidity
10% to 90% RH
Storage Humidity
5% to 90% RH
Fan
N/A
Temperature
Warning
Supported
EMC Standards
GB9254-1998
Safety Standards
GB4943-2001
Dimensions
(W x D x H)
RG-S2928G-E V1.00 and later: 440 mm x 200 mm x 43.6 mm
RG-S2928G-E V2.00 and later: 440 mm x 260 mm x 43.6 mm

Weight
Less than 3.5 kg
RG-S2928G-E switch is a class A product. In a domestic environment, this product may cause radio interference in
which case the user may be required to take adequate measures.
Product Appearance
The front panel of the RG-S2928G-E full gigabit Ethernet switch provides one Type-A USB2.0 interface, one RJ45
console port, 24 RJ45 10/100/1000Base-T Ethernet adaptive ports and four SFP ports. Figure 1-1 shows the appearance
of the RG-S2928G-E.
Figure 1-1 Appearance of the RG-S2928G-E
Front Panel
Figure 1-2 Front Panel of the RG-S2928G-E
Note:
1. USB2.0 port
2. RJ45 console port
3. RJ45 10/100/1000Base-T adaptive Ethernet
port
4. 100Base-FX/1000Base-X SFP port
5. 100Base-FX/1000Base-X SFP/2.5 G stack port
6. Switch system status indicator
7. 10/100/1000Base-T adaptive Ethernet port indicator
8. 100Base-FX/1000Base-X SFP/2.5 G stack port
indicator
Only the four SFP ports of the RG-S2928G-E V2.00 and later support 100Base-FX.

Back Panel
Figure 1-3 Back Panel of the RG-S2928G-E
Note:
1. Grounding pole
2. Three-hole AC power receptacle
3. Power cord retention clips
Power Supply
The RG-S2928G-E switch can be powered either with AC power or DC power.
AC input:
Rated voltage range: 100 V to 240 V
Maximum voltage range: 90 V to 264 V
Frequency: 50 Hz to 60 Hz
Rated current: 0.6 A
Power cord: 10A power cord
HVDC input:
Maximum voltage range: 192 V to 290 V
Rated current: 0.2 A to 0.12 A
Power cord: 10A power cord
Heat Dissipation
The RG-S2928G-E full gigabit switch is designed with no fans. To ensure good dissipation, sufficient space (10 cm
distance from both sides and the back panel of the chassis) should be reserved for ventilation. Dust the device every three
months to avoid blocking the ventilation openings.
When installing the device, sufficient ventilation space (1 U (44.45 mm) distance from the adjacent device) should be
reserved for the purpose of heat dissipation.
LED Indicators
Indicator
Faceplate
Marker
Status
Indication
Status indicator
Status
Blinking green
The system is being initialized.
Solid green
The system is in normal operation. .

Indicator
Faceplate
Marker
Status
Indication
Solid yellow
System over-temperature warning.
Solid red
Serious over-temperature, the system will stop
working forcibly by itself.
10/100/1000 Mbps RJ-45 port
indicator
1~24
Off
The port is NOT connected.
Solid green
The port is connected at 1000Mbps.
Solid yellow
The port is connected at 100/10Mbps.
Blinking
The port is transmitting or receiving data.
100Base-FX/1000Base-X/Stack
port indicator
(Note: Only the four SFP ports
of the RG-S2928G-E V2.00 and
later support 100Base-FX.)
25F~28F
Off
The port is NOT connected.
Solid green
The port is connected.
Blinking
The port is transmitting or receiving data.
1.2 RG-S2952G-E
Technical Specifications
Model
RG-S2952G-E
CPU
Single-core CPU, clock speed of 600M
BOOTROM
8M
Flash Memory
128M
SDRAM
DDRII 128MB
Supported
SFP Type
Gigabit Ethernet:
MINI-GBIC-SX-MM850
MINI-GBIC-LX-SM1310
MINI-GBIC-LH40-SM1310
MINI-GBIC-ZX50-SM1550
MINI-GBIC-ZX80-SM1550
MINI-GBIC-ZX100-SM1550
Fast Ethernet:
FE-SFP-LX-MM1310
FE-SFP-LH15-SM1310
1000Base-T:
Mini-GBIC-GT
2.5 G stack module:
GE-SFP-STACK1.6M
The supported module type may change at any time. Contact us for the detailed change

information.
Only the four SFP ports of the RG-S2952G-E V2.00 and later support fast Ethernet SFP
modules.
SFP Port
Support 1000 Base-X, 1000 Base-T, 100 Base-FX and 2.5 G stacked SFP module
Only the four SFP ports of the RG-S2952G-E V2.00 and later support 100Base-FX.
USB Port
One Type-A USB2.0 interface
Power Supply
AC input:
Rated voltage range: 100 V to 240 V
Maximum voltage range: 90 V to 264 V
Frequency: 50/60 Hz
Rated current: 2 A
HVDC input:
Maximum voltage range: 192 V to 290 V
Rated current: 0.3 A to 0.17 A
EEE
Not supported on the RG-S2952G-E V1.00 and later
Supported on the RG-S2952G-E V2.00 and later
PoE
Not supported.
Power
Consumption
Less than 59 W on the RG-S2952G-E V1.00 and later
Less than 49 W on the RG-S2952G-E V2.00 and later
Working
Temperature
0ºC to 50ºC
Storage
Temperature
-40ºC to 70ºC
Working
Humidity
10% RH to 90% RH
Storage
Humidity
5% RH to 90% RH
Fan
Support adjustment of fan speed and warning of fan troubles.
Temperature
Warning
Supported
EMC
Standards
GB9254-1998
Safety
Standards
GB4943-2001
Dimensions
(W x D x H)
440 mm x 260 mm x 43.6 mm
Weight
Less than 4 kg

RG-S2952G-E switch is a class A product. In a domestic environment, this product may cause radio interference in
which case the user may be required to take adequate measures.
Product Appearance
The front panel of the RG-S2952G-E full gigabit Ethernet switch provides one Type-A USB2.0 port, one RJ45 console port,
48 RJ45 10/100/1000Base-T adaptive Ethernet ports and four SFP ports. Figure 1-4 shows the appearance of the
RG-S2952G-E.
Figure 1-4 Appearance of the RG-S2952G-E
Front Panel
Figure 1-5 Front Panel of the RG-S2952G-E
Note:
1. USB2.0 port
2. RJ45 console port
3. RJ45 10/100/1000Base-T adaptive
Ethernet port
4. 100 Base-FX/1000 Base-X SFP port
5. 100 Base-FX/1000 Base-X SFP/2.5 G stack port
6. System status indicator
7. 10/100/1000 Base-T adaptive Ethernet port indicator
8. 100Base-FX/1000Base-X SFP/2.5 G stack port
indicator
Only the four SFP ports of the RG-S2952G-E V2.00 and later support 100 Base-FX.
Back Panel
Figure 1-6 Back Panel of the RG-S2952G-E V1.00 and Later